NOKTA 10000103 Ultra Scanner Security Metal Detector User Manual
- June 4, 2024
- Nokta
Table of Contents
Ultra Scanner
USER MANUAL
10000103 Ultra Scanner Security Metal Detector
Thank you for choosing and purchasing our Nokta Ultra Scanner.
Nokta Ultra Scanner s a hand-held metal detector designed to find all kinds of ferrous and non-ferrous metals carried on a person or ns de a non-metal object.
WARNINGS and REMINDERS
- Do not expose the device to very hot or cold conditions for extended periods of time.
- Do not immerse the device in water; do not expose it to extreme hum d conditions.
- Always keep the device off when not in use. This will help increase battery life and device performance.
- Do not leave the battery inside the device if the device will be stored for a long time.
- Audio alert consumes less battery power than vibrant on alert. Using the audio alert when possible will extend battery life.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operate on s subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
For Consumers within the European Union: Do not dispose of this equipment n general household waste. The crossed-wheeled-in symbol on this equipment and cates this unit should not be d sposed of n general household waste but recycled in compliance with local government regulations on and environmental requirements.
COMPONENTS
OPERATING INSTRUCTIONS
Battery
To open the battery compartment, place your thumb on the recess, press down
and slide forward.
Insert the supplied 9V battery paying attention to the plus (+) and minus (-)
poles.
If the battery is inserted in the wrong direction, the battery cover will not
close.
Low Battery Life Alert
When the battery is low, the yellow LED will blink continuously and the
device will provide a warning audio every 5 minutes. The device will continue
working until the battery dies.
Earphone/Charger Jack
For a silent operation or to use the device more conveniently in noisy
environments, insert the optional earphone jack here.
Important: The optional earphone is “MONO”. Using “STEREO” earphones may
harm the device.
You can charge the rechargeable 9V battery on the device by inserting the charger plug into the Earphone/Charger jack. When charging starts, the green LED will light up. As the battery starts filling up, the Signal/Battery Level LEDs will start lighting in order and when the charging is complete they will all start blinking indicating full charge.
Important: Trying to charge regular, non-rechargeable batteries may harm your device.
Turning On the Device
Before turning on the device, hold the device away from metallic objects
including your watch and jewelry. Turn on the device by sliding the switch to
either audio or vibration alert.
When the device is turned on a long beep will be heard and the green LED will
illuminate. On initial start up, the red LEDs will light up indicating battery
life status and then go off. During use, the red LEDs will indicate the signal
and sensitivity level.
Volume Control
The device has 2 levels of volume. For higher ae volume, press and hold
button 1 and press button 3) 7 3 at the same time. For lower volume, press and
hold button 1 and press button 2 at the same time. The volume control does
affect the earphone audio.
Audio or Vibration Alert
The device operates on the principle of motion. The device will not produce
a signal when held still over a metal. You must move the device over the metal
in order for the device to detect it. When the device detects metal, it will
produce an audio or vibration alert according to your mode selection. The rate
of the pulsing audio or vibrations will increase as the device gets closer to
the metallic object and it will decrease as the device is moved away. When the
device is in audio mode the red LEDs will also illuminate according to the
signal strength providing visual warning as well.
Sensitivity and Signal Level Indicator
The red LEDs indicate the device’s sensitivity level (except for the Basic
model) as well as the signal level when metal is detected in audio mode. You
can adjust the sensitivity based on surrounding conditions and your preference
using the up and down arrow keys. At maximum sensitivity, all red LEDs will
light up and at minimum, only a single LED will illuminate.
As mentioned above, when metal is detected in audio mode the red LEDs will provide visual warning by lighting up according to the strength of the signal received from the metal.
Interference Elimination Button
The device is set for maximum sensitivity for the smallest objects. This
may cause the device to produce signals when held close to a floor with metal
construction. You may enable the device not to respond to metals under the
floor by pressing and holding this button. When released, the device will go
back to its previous sensitivity level.
Internal Sensitivity Setting
Some applications may require different sensitivity setting from the
factory setting. An internal sensitivity setting has been placed under the
rubber handle cover. You can access this setting by pulling back the rubber
and adjust the sensitivity by a screwdriver using a test object of your
choice. The sensitivity will increase as you turn the setting clockwise and it
will decrease when turned counterclockwise.
Please keep in mind that when the sensitivity is increased the device may get affected by the surrounding metals and receive noise. Be sure to check that the sensitivity is at the desired level by testing it with appropriate targets each time the internal sensitivity setting is changed. It is recommended that only technicians should change this setting.
Turning Off the Device
Turn off the device by sliding the switch to the off position in the middle.
Always keep the device off when not in use.
Belt Holster
When you are not using the Ultra Scanner, you can put it in the holster and
attach it to your belt.
Safety Notice
Research evidence indicates that use of hand-held metal detectors have no
adverse affect on pregnancies or pacemakers. However, it is strongly
recommended that for use on other personal medical electronic devices, the
advice from the manufacturer or physicians should be followed.
Technical Specifications
- Audio Frequency………………..: 2KHZ
- Operating Frequency………….: 50KHz
- Voltage ………………………………: 6.8V- 10.5V
- Current……………………………….: 4.5 mA (Standby)
- Dimensions (LxWxD)…………: 40×8.5x3cm. (15.7″x3.3″x1.2″)
- Weight…………………………………: 400gr. (14.1 02.)
- Operating Temperature……….: -20°C (-4°F) to 60°C (140°F) (95% Humidity)
- Battery…………………………………: 9V Alkaline
- Battery Life………………………….: Up to 100 hours
Nokta Detectors reserves the right to change the design, specifications, or accessories without notice and without any obligation or liability whatsoever.
WARRANTY
Nokta Detectors warrants to the end-user customer that this product will be free from defects in material and workmanship for a period of 2 years from the date of purchase (excluding the accessories). Nokta Detectors’ limited warranty covers only those defects that arise as a result of normal use of the product in accordance with Nokta Detectors’ printed instructions and does not cover any other problems, including those that arise as a result of accident, misuse, negligent act or improper maintenance. The customer must return any defective device to Nokta Detectors or to one of its authorized dealers with freight prepaid. If Nokta Detectors receives, during the applicable warranty period, notice of a defect which is covered by Nokta Detectors’ warranty, Nokta Detectors shall either repair or replace the product, at its sole discretion.
MANUFACTURER
Name : NOKTA DETECTORS
Address : EMEK MAH. SIVAT CAD. SAKIZ SOK. NO:4/1
City / Country : SANCAKTEPE – ISTANBUL / TURKEY
Phone / Fax : +90 (216) 415 56 86 / +90 (216) 415 63 43
PRODUCT
Brand : NOKTA
Model : Ultra Scanner
Product ID / Serial :
Number :
DISTRIBUTER / DEALER
Name :
Address :
City / Country :
Phone / Fax :
Invoice Date :
Invoice Number :
Signature / Seal :
Emek Mh. Sivat Cd. Sakiz Sk. No: 4/1
34785 Sancaktepe – Istanbul / Turkey
Phone : +90 216 415 56 86
Fax : +90 216 415 63 43
E-mail: [email protected]
55000311