AQUABATOS FSP204 Corner Shower with Swing Doors Instruction Manual
- June 9, 2024
- AQUABATOS
Table of Contents
AQUABATOS FSP204 Corner Shower with Swing Doors
OVERVIEW
Prior to installation
- Prior to installation please carefully examine the shower enclosure for transport or other damage. A thorough examination of all glass parts is essential for your own safety.
- Seemingly minor damage may cause breakage of glass and for this reason, extra care must be taken not to damage the glass edges of the shower enclosure during installation or use of the shower enclosure. Claims for transport damage after installation and claims for damage or cost caused by incorrect installation, cleaning, and maintenance will not be paid. Personal protective equipment is recommended!
- Shower enclosures are intended for installation on shower trays. If installed without a shower tray, the floor on which the shower enclosure will rest must be flat and level.
- If installing on a joint or uneven surface, you must ensure this is properly siliconed to form a waterproof and maintenance-free seal. When assembled off-floor or with a step, you must take appropriate measures to prevent slip hazards on entry and exit. Before drilling the raw plug holes, the wall has to be tested for concealed service pipes (electricity-, gas- or water pipes).
- Drilling into these pipes is a life-threatening hazard as well as damage to property. Shower enclosures should be installed on solid walls and bases. If installing on non-solid walls and bases, you must ensure appropriate stability on site (e.g. by using special raw plugs). Please use adequate and correct silicone appropriate for the installation (e.g. for marble)
TOOL LIST
DESCRIPTION | BILD |
---|---|
I’m hanging up | |
level |
Rigid
|
06mm drill|
03mm drill|
DESCRIPTION|
---|---
drilling machine
|
Flat Head Screwdriver|
cross screwdriver|
Hammer
|
silicone syringe
| ****
CANNES corner shower with revolving doors on fixed parts
ASSEMBLY INSTRUCTIONS – DRAWING
- 2x wall profile cover cap
- 12x dowels
- 6x round head screw ST 4×30
- 12x screw cap terminals
- 12x round head screw ST 4×12
- 12x screw cover cap
- 4x Glass Clamp A
- 4x shower tray
- 4x Glass Clamp B
- 2x Fixed Plate
- 2x Movable Plate
- 2x bottom seal
- 2x Endabdeckung L&R
- 2x Abtropfleiste
- 1x Endabdeckung A
- 1x EndabdeckungB
- 4x Flachkopfschraube ST 3.5×30
- 2x Griff
- 2x Magnetdichtung (Bewegliche Platte)
- 2x Vertikalesprofil Abdeckkappe B L&R
- 2x Stabilisationsstange
- 2x Flachkopfschraube ST 4×30
- 1x Holz Abstandshalter
INSTALLATION GUIDE
If you need assistance, we recommend that you contact a competent Contact plumber.
Step 1
Step 2
A Shower tray installation dimensions | B Shower cabin installation dimension |
---|---|
88 – 90 cm | 87 – 89 cm |
93 – 95 cm | 92 – 94 cm |
98 – 100 cm | 97 – 99 cm |
108 – 110 cm | 107 – 109 cm |
118 – 120 cm | 117 – 119 cm |
- Shower tray installation dimensions the clear external dimensions of the
- Shower tray, measured from the wall to the outer edge of the tub.
- Shower stall installation dimensions = the maximum possible
- Outer dimensions, measured from the wall to the outer edge of the profile.
Step 3
Step 4
Step 5
Notice:
Please make sure that the bottom of the magnet seal flush with the bottom
first the glass pane closes.
Step 6
Step 7
Step 8
Step 9
Step 10
Step 11
Step 12
Silicone must dry for 24 hours before use. Silicone only on the outer edge.
Aqua Batos Bäder GmbH Südwestkorso 14 12161 Berlin
info@aquabatos.com
www.aquabatos.de
V01.09.2021
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>