V I V O DESK-VE36K Electric Motor Desk Converter Instruction Manual
- June 15, 2024
- V I V O
Table of Contents
V I V O DESK-VE36K Electric Motor Desk Converter
Product Information
Specifications
- Product Name: Black Electric Desk Riser
- SKU: DESK-VE36K
- Weight Capacity: 44lbs (20kg) for the desktop, 4.4lbs (2kg) for the keyboard tray
Package Contents
- (x1) Desk (A)
- (x1) Keyboard Tray (B)
- (x4) Sleeve Nut with Screw (C)
- (x2) Cable Clip (D)
- (x3) Pad Rubber Feet (E)
- (x4) Scissors (F)
- Phillips Screwdriver
Assembly Steps
-
Step 1
Separate the sleeve nut with screw (C) into (C1) and (C2). -
Step 2
Apply Pads (E) to the underside of Keyboard Tray (B). Press Sleeve Nut (C1) into the holes on top of Keyboard Tray (B). -
Step 3
Install Feet (F) to the bottom of Desk (A). Then cut the large plastic safety tie. Plug Desk (A) into a wall outlet, and press the up arrow on the control panel to fully raise the desktop. -
Step 4
Place Keyboard Tray (B) on metal brackets on Desk (A). While holding Sleeve Nuts (C1), secure Keyboard Tray (B) to brackets using Screws (C2) and tighten with a Phillips screwdriver. -
Step 5
Apply cable clips (D) to the underside of the desk. -
Step 6
If installing a monitor mount, remove the plug from the desktop, then secure the mount using grommet mounting hardware included with your monitor mount.|
CAUTION!
- Keep the monitor and laptop base fully on the desktop.
- Follow the cable routing instructions to avoid the potential to pinch cables.
- Leave enough slack in the cable to allow for full range of vertical motion (15 / 38 cm).
- Raise the desktop slowly to keep items stable.
FAQ
What is the weight capacity of the desk?
The weight capacity of the desk is 44lbs (20kg).
Can children use this product?
No, this product contains small parts and is not suitable for children under 3 years. Adult supervision is required.
How do I install the keyboard tray?
To install the keyboard tray, follow Step 2 in the assembly steps provided. Apply pads to the underside of the keyboard tray and press sleeve nut (C1) into the holes on top of the tray. Then, place the tray on the metal brackets on the desk and secure it using screws (C2) and a Phillips screwdriver while holding the sleeve nuts.
Can I install a monitor mount on this desk?
Yes, you can install a monitor mount on this desk. Please refer to Step 6 in the assembly steps for instructions on how to secure the mount using grommet mounting hardware.
What should I do if I receive damaged or defective parts?
If you receive damaged or defective parts, please contact our support team at help@vivo-us.com or call 309-278-5303. We are happy to replace parts to ensure you have a fully functioning product.
SKU: DESK-VE36K
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/desk-ve36k
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
- help@vivo-us.com
- www.vivo-us.com Chat live with an agent!
- 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual and do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly, or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
WARNING
PINCH POINT
DO NOT place hands on or near support bars. Moving parts can crush and cut.
Pinch points are created during lifting and lowering the worksurface. Failure
to follow these instructions may result in serious personal injury.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
-
STEP 1
Separate the sleeve nut with screw (C) into (C1) and (C2). -
STEP 2
Apply Pads (E) to underside of Keyboard Tray (B). Press Sleeve Nut (C1) into holes on top of Keyboard Tray (B).
- STEP 3
Install Feet (F) to the bottom of Desk (A). Then cut the large plastic safety tie. Plug Desk (A) into a wall outlet, and press the up arrow on the control panel to fully raise the desktop.
- STEP 4
Place Keyboard Tray (B) on metal brackets on Desk (A). While holding Sleeve Nuts (C1), secure Keyboard Tray (B) to brackets using Screws (C2) and tighten with a Phillips screwdriver.
- STEP 5
Apply cable clips (D) to underside of desk.
- STEP 6
If installing a monitor mount, remove the plug from the desktop, then secure the mount using grommet mounting hardware included with your monitor mount
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 08/25/2022 REV2
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
-
309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
-
www.vivo-us.com Chat live with an agent AVG. RESOLUTION TIME (within office hrs): < 15 M
-
help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M
-
23% within < 15m
38% within < 30m -
61% within < 1hr
-
83% within < 2hr
-
92% within < 3hr
-
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.co
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- 36" Electric Standing Desk Converter – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>