V I V O DESK-V100EW White Electric Single Motor Desk Frame Instruction Manual
- June 15, 2024
- V I V O
Table of Contents
V I V O DESK-V100EW White Electric Single Motor Desk Frame
Product Information
Specifications:
- Model: White Electric Single Motor Desk Frame
- SKU: DESK-V100EW
- Weight Capacity: 176lbs (80kg)
Package Contents:
- (x1) Left Crossbar (A)
- (x1) Right Crossbar (B)
- (x1) Center Crossbar (C)
- (x1) Leg (D)
- (x1) Motorized Leg (E)
- (x2) Side Bracket (F)
- (x2) Foot (G)
- (x1) Sync Rod (H)
- (x1) Controller (I)
- (x1) AC Adapter (J)
- (x12) Anti-Vibration Pad (K)
- (x2) Cable Clip (L)
- (x22) M6x11mm Screw (S-A)
- (x14) M5x16mm Screw (S-B)
- Tools Needed: 2mm Allen Wrench (T-A), 5mm Allen Wrench (T-B),
Phillips Screwdriver
Usage Instructions
- Step 1: Assemble the Left Crossbar (A) to the Leg (D) and the Right Crossbar (B) to the Motorized Leg (E) using the provided M6x11mm Screws (S-A) and the 5mm Allen Wrench (T-B).
Diagram:
Step 2:
Secure the Side Brackets (F) to the Leg (D) and the Motorized Leg (E) using
the provided M6x11mm Screws (S-A) and the 5mm Allen Wrench (T-B).
Diagram:
Step 3:
Assemble the Feet (G) to the Leg (D) and the Motorized Leg (E) using the
provided M6x11mm Screws (S-A) and the 5mm Allen Wrench (T-B).
Diagram:
Step 4: Insert the Center Crossbar (C) into the Left Crossbar (A) and the Right Crossbar (B). Secure the Center Crossbar (C) using the provided M6x11mm Screws (S-A) and the 5mm Allen Wrench (T-B).
Diagram:
Step 5: Loosen the knob on the Sync Rod (H) and extend the hex shaft. Insert the hex shaft into the Leg (D), making sure the metal retaining ring makes contact with the Leg (D). While holding the hex shaft with one hand, extend the Sync Rod (H) onto the spline shaft of the Motorized Leg (E). Tighten the Sync Rod (H) using the provided 2mm Allen Wrench (T-A) and retighten the knob.
Diagram:
Step 6: Apply the Anti-Vibration Pads (K) to the Side Brackets (F), Left Crossbar (A), and Right Crossbar (B).
Diagram:
Step 7:
Secure the frame assembly and the Control Panel (I) to the desktop using
the provided M5x16mm Screws (S-B) and a Phillips screwdriver.
Diagram:
Step 8:
Plug the cable from the Motorized Leg (E) and the AC Adapter (J) into the
Controller (I). Organize cables using the Cable Clips (L). Plug the AC Adapter
(J) into an AC wall outlet.
Diagram:
FAQ:
-
Q: What is the weight capacity of the desk?
A: The weight capacity of the desk is 176lbs (80kg). -
Q: What should I do if the desk is unable to move?
A: Disconnect the power for 30 seconds, then plug the desk back in. Once the power has been reconnected, follow the reset procedure. -
Q: How do I adjust the height of the desk?
A: Press and hold the up arrow until the desk reaches the desired height. -
Q: How do I reset the desk?
A: Press and hold the down arrow until the desk reaches its lowest height and rebounds slightly, then release the down arrow. -
Q: What precautions should I take when using the desk?
A: Do not exceed the weight limit of the desk. Keep the area of vertical motion free of obstacles. Keep the weight on the desk balanced for correct operation and longer life of components. Leave enough slack in cables to allow for full range of vertical motion.
White Electric Single Motor Desk Frame
Instruction Manual
SKU: DESK-V100EW
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/desk-v100eb
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual and do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly, or inappropriate use.
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
- DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
- DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
- NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
- NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
- ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
- OUTDOOR USE IS PROHIBITED
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS
REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE MAY NOT BE USED
TOOLS NEEDED DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
- STEP 1 Assemble Left Crossbar (A) to Leg (D) and Right Crossbar (B) to Motorized Leg (E) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-B).
- STEP 2 Secure Side Brackets (F) to Leg (D) and Motorized Leg (E) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-B).
- STEP 3 Assemble Feet (G) to Leg (D) and Motorized Leg (E) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-B).
- STEP 4 Insert Center Crossbar (C) into Left Crossbar (A) and Right Crossbar (B). Secure Center Crossbar (C) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-B).
- STEP 5 Loosen the knob on Sync Rod (H) and extend the hex shaft. Insert the hex shaft into Leg (D), making sure the metal retaining ring makes contact with Leg (D). While holding the hex shaft with one hand, extend Sync Rod (H) onto the spline shaft of Motorized Leg (E). Tighten Sync Rod (H) using 2mm Allen Wrench (T-A). and retighten the knob.
- STEP 6 Apply Anti-Vibration Pads (K) to Side Brackets (F), Left Crossbar (A) and right Crossbar (B).
- STEP 7 Secure the frame assembly and Control Panel (I) to the desktop using M5x16mm Screws (S-B) and a Phillips screwdriver.
- STEP 8 Plug the cable from Motorized Leg (E) and AC Adapter (J) into Controller (I). Organize cables using Cable Clips (L). Plug AC Adapter (J) into an AC wall outlet.
- Reset Press and hold the down arrow untill the desk reaches its lowest height and rebounds slightly, then release the down arrow.
- Height Adjustment Press and hold the up arrow until the desk reaches the desired height.
- Troubleshooting If the desk unable to move, disconnect the power for 30 seconds, and plug then plug the desk back in. Once the power has been reconnected, follow the reset procedure.
CAUTION!
- Do not exceed desk weight limit.
- Keep area of vertical motion free of obstacles.
- Keep weight on desk balanced for correct operation and longer life of components.
- Leave enough slack in cables to allow for full range of vertical motion.
Failure to follow these instructions may result in property damage and/or personal injury.
Love your new VIVO setup and want to share? Tag us in your photo!
@vivo_us
LAST UPDATED: 08/30/2022 REV1V
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer
immediate assistance with rapid response times. If any parts are received
damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
- 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
- www.vivo-us.com Chat live with an agent! AVG. RESOLUTION TIME (within office hrs): < 15 M
- help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Electric Single Motor Desk Frame with 2 Button Controller – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>