DENALI 20V Cordless Drill Impact Driver User Manual
- June 14, 2024
- DENALI
Table of Contents
DENALI 20V Cordless Drill Impact Driver
PRODUCT INFORMATION
WARNING
-
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are:
- Lead from lead-based paints.
- Crystalline silica from bricks, cement, and other masonry products.
- Arsenic and chromium from chemically treated lumber.
-
Your risk from these exposures varies, depending on how often this type of work is done.
To reduce the exposure to mentioned chemicals:- Work in a well-ventilated area.
- Work with approved safety protective equipment (PPE), such as dust masks that are specially designed to filter out microscopic particles.
- Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Do not allow dust to get into your mouth or eyes or to rest on the skin as this may promote absorption of harmful chemicals.
Safety Warnings
General power tool safety warnings
WARNING
Read all safety warnings, instructions, illustrations, and specifications
provided with this power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
- Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
- When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
- If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. The use of a GFCI reduces the risk of electric shock.
Personal safety
- Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
- Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
- If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
- Do not let familiarity gained from the frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care
- Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
- Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts the eyes, seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
- Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 266 °F (130 °C) may cause an explosion.
- Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
Service
- Has wider sure ento ole sarice the goalf ed is maintain using only identical replacement parts.
- Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
Impact driver safety warnings
Hold the power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory or fastener may contact hidden wiring.
Fasteners contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
Additional safety warnings
- Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body is unstable and may lead to loss of control.
- Keep handles dry, clean and free from oil and grease. Slippery hands cannot safely control the power tool.
- Develop a periodic maintenance schedule for your power tool. When cleaning a power tool be careful not to disassemble any portion of the power tool since internal wires may be misplaced or pinched or safety guard return springs may be improperly mounted. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.
- To reduce the risk of explosion, electric shock and property damage, always check the work area for hidden gas pipes, electrical wires or water pipes.
- Hold the power tool securely. When tightening and loosening the screws/bolts be prepared for temporary high torque reactions.
Vibration and noise reduction
To reduce the impact of noise and vibration emission, limit the time of
operation, use low-vibration and low-noise operating modes as well as wear
personal protective equipment (PPE).
Take the following points into account to minimize the vibration and noise exposure risks:
- Only use the power tool as intended by its design and these instructions.
- Ensure that the power tool is in good condition and well-maintained.
- Use the correct attachments for the power tool and ensure they are in good condition.
- Keep a tight grip on the handles/gripping surfaces.
- Maintain the power tool in accordance with these instructions and keep it well-lubricated (where appropriate).
- Plan the work schedule to spread any high-vibration tool use across a longer period of time.
Residual risks
Even if you are operating this power tool in accordance with all the safety
requirements, potential risks of injury and damage remain. The following
dangers can arise in connection with the structure and design of this power
tool:
- Health defects result from vibration emission if the power tool is used over long periods of time or not adequately managed and properly maintained.
- Injuries and damage to property due to broken attachments or the sudden impact of hidden objects during use.
- Hearing loss due to prolonged exposure to noise.
Description of Symbols
The symbols and abbreviations below are used in these instructions and on
the labels on the power tool. Get familiarized with the meaning of these
symbols and abbreviations before using the power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury.
Signal words
- DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
- WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
- CAUTION , used with the safety alert symbol, indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
- NOTICE is used to address practices not related to personal injury.
Symbol explanation
FCC – Supplier’s Declaration of Conformity
- Unique Identifier : AID5727B-00 – Amazon Brand – Denali by SKIL 20V Impact Driver
- Responsible Party: Amazon.com Services LLC.
- U.S. Contact Information : 410 Terry Ave N. Seattle, WA 98709 USA
- Telephone Number: 206-266-1000
FCC Compliance Statement
- This device complies with Part 1 S of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 1 S of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
DANGER : People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker.
Canada IC Notice
This Class B digital apparatus complies with Canadian CAN ICES-003(B) /
NMB-003(B) standard.
Specifications
- Model number: AID5727B-00
- Rated voltage: 20 V
- Rated no-load speed n0: 0-2500 rpm
- Impact rate: 0-3200 pm
- Maximum torque : 1100 in· lb
- Collet capacity: 01/4″ (6.35 mm) hex (power groove impact bits only)
- Recommended working temperature: + 14 °F to +104 °F (-10 •c to +40 °C)
- Recommended storage temperature : + 32 °F to +104 °F (0 •c to +40 °C)
- Recommended charging temperature: + 41 °F to +104 °F (+S •c to +40 °()
- Net weight: approx. 1.96 lbs (0.89 kg) (without battery)
- Dimensions (W x H x D): approx. 6.1 x 7.48 x 2.83″ (15.5 x 19 x 7 .2 cm) (without battery)
Feedback and Help
We would love to hear your feedback. To ensure we are providing the best
customer experience possible, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:
If you need help with your Denali product, please use the website or number below.
MADE IN CHINA