ione A02PRO Wireless Active Noise Cancelling Headphone User Guide
- June 6, 2024
- ione
Table of Contents
ione A02PRO Wireless Active Noise Cancelling Headphone
WIRELESS ACTIVE NOISE CANCELLING HEADPHONES
- 40mm Hi-Resolution drivers built with special tuning titanium diaphragm
- Advanced hybrid active noise cancellation Digital processor
- Support Sony LDAC Hi-Resolution Bluetooth Audio Codec
- Build-in Spatial Audio Technology
- Ambient and music balance control
- 5 Audio enhanced equalizer presets for Jazz/ Classic/ Dance / Rock / Pop music
PACKAGE CONTENT
- Headphone (Model Name: A02PRO)
- USS Type-C Charging Cable
- Headphone Jack Adapter
- 3.5mm Audio Cable
- Quick Start Guide
HARDWARE REQUIREMENTS
- Compatible with BT 5.0 device
APP REQUIREMENTS
- Android 6 / IOS 12
PRODUCT OVERVIEW
A. Headset (40mm Hi-Resolution Dynamic Drivers)
B. Self-adjusting Headband
C. Protein Ear Cushion
D. 1.2 Meter USS Charging Cable
E. 1.8 Meter 3.5mm Audio Cable
F. Airplane 3.5mm Headphone Jack Adapter
G. Power/Pairing Button
H. Play/Pause Button
I. Normal/ANG/Ambient Mode Button
J. Volume Up Button
K. Volume Down Button
L. Microphone
M. Audio Jack (AUX cannot be used at the same time while charging)
N. USS Type C Jack
START USING
WIRELESS MODE
RECHARGE
Plug the [D. USB Charging Cable] (TYPE C) into the earphone and the other end (TYPE A) into the computer USB port to start charging. Let the battery is fully charged before its first use.
- Low battery: Red light flashes every 5 minutes, and the voice prompt battery low
- Charging: Light will turn solid red
- Charging completed: Light will turn solid green
- Battery is too low: The red light flashes for 1 second and then shuts down
BLUETOOTH
- Turn on Bluetooth pairing mode (mobile phone): Press [G. Power Button] for 5 seconds, the red light and green light alternately flash for 60 seconds
- Pairing is complete: Blue light flashes for 2 seconds, voice prompt Connected
POWER ON/OFF
- Power on: Press [G. Power Button] for 2 seconds, the green light will be on for 2 seconds, and the voice prompt Power On
- Power off: Press [G. Power Button] for 2 seconds, the red light will be on for 1 second, and the voice prompt Power Off
PLAY
- Play/Pause: Press the [H. Play/Pause Button] once
- Volume+/-: Press [J. Volume Up Button] once I Press [K. Volume Down Button] once
- Previous song: Press and hold the [J. Volume Up Button] for 1 second
- Next song: Press and hold the [K. Volume Down Button] for 1 second
MODE
- Normal-+ANC: In normal mode, press (I. Mode Button) once, the blue light will turn on for 2 seconds to enter the ANC mode
- ANC-+Ambient: In ANC mode, press [I. Mode Button] once, the white light will turn on for 2 seconds to enter the Ambient mode
- Ambient-+Normal: In the ambient mode, press the [I. Mode Button] once to enter the normal mode.
PHONE CALL
- Receiving a call: Press the [H. Play Button] once
- Ending the call: Short press the [H. Play] button, the blue light flashes for 2 seconds
- Reject the call: Press and hold the [H. Play Button] for 2 second
- (Incoming call during a call) Hold the call and answer the interrupted call: Press the [H. Play Button] once
- (Incoming call during a call) Ending the call and return to the original call: Press and hold the [H. Play Button] for 1 second
- (Incoming call during a call) Rejection of Interruption: Short press the [H. Play] button once
WIRED MODE
After powering on, plug [E. 3.5mm Audio Cable] into the headphone and the other end into the device to start using the earphone
-
In use: steady green light
-
Power off: Red light lasts for 1 second
-
In wired mode, but you need to use equipment to control the play such as a computer
FCC
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol lowing measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
FCC RF Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further
RF exposure reduction can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output power if such
function is available..
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
WARNING
- To avoid hearing damage and damage to the earphones, use the earphone at a comfortable, moderate volume level. Turn the volume up gradually until you reach a comfortable level.
- Earphones should keep away from fire, or in the situation with high temperature or high pressure.
- Do not immerse the earphones into the water or place the earphones in high humidity situation for long time.
- Stop using the earphones if you find liquid leakage, overheating or other unusual conditions.
- Do not try to disassemble or short circuit the earphones.
Use the LISTEN App for setup, product customization and music enhancing features.
| 
---|---
IONE ELECTRONIC TECHNOLOGY CO., LTD. TAIWAN BRANCH
www.ione.com.tw/ione@ione.com.tw
www.ione-europe.com/info@ione-europe.com
www.ione-usa.com/support@ione-usa.com
www.ione-cn.com/ione@ione-cn.com
www.ione-th.com/ione@ione-th.com
© 2021 ione® .All rights reserved. ione®, the ione logo, and product names referred to herein are the registered trademarks of lone Technology Inc. All other trademarks are the property of their respective owners.
