Westinghouse ETL-ES-Albert-WH22 52 Inch Five Blade Indoor Ceiling Fan Owner’s Manual
- June 14, 2024
- Westinghouse
Table of Contents
ETL-ES-Albert-WH22 52 Inch
Five Blade Indoor Ceiling Fan
**Owner’s Manual
Net Weight: 16.83 LBS
Peso Neto: 7.65 KGS
**
Albert
Please write model number here for future reference:
SAFETY TIPS
OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY,
MOUNT TO OUTLET BOX MARKED ‘ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR
LESS’ AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX AND/OR SUPPORT
DIRECTLY FROM BUILDING STRUCTURE. MOST OUTLET BOXES COMMONLY USED FOR THE
SUPPORT OF LUMINARIES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE
REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT.
-
Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards (ANSI/NFPA 70), including fire-rated construction.
-
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
-
After making the wire connections, gently push connections into outlet box with wire nuts pointing up. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on
one side of the outlet box and ungrounded conductor on the other side of the outlet box. -
Before you begin installing the fan, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel. -
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
-
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
-
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blade.
-
To reduce the risk of fire, electric shock, or personal injury, this fan must be mounted to an outlet box marked suitable for fan support, and use the mounting screws provided with the outlet box. (Mounting must support at least 35 lbs.)
-
WARNING! Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.
-
Attach the mounting bracket using only the hardware supplied with the outlet box. Fan is only to be mounted to an outlet box marked “Acceptable for Fan Support”.
-
WARNING! To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
-
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
-
NEVER place a switch where it can be reached from a tub or shower.
-
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
-
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
-
All set screws must be checked and re-tightened where necessary before installation.
-
Keep electrical appliances out of reach of children or infirmed persons. Do not let them use the appliances without supervision.
TOOLS REQUIRED
Phillips Screwdriver Wire Cutters Pliers Step Ladder
FEATURES
Note : For pitched ceiling installation, please refer to westinghouselighting.com for specially designed canopy kit options.
COMBO-BLADE
Combo-Blades feature two high quality finishes on one blade. Select the one
that best complements your decor, or change the style with just a flip of the
blade.
NOTE : Combo-Blade finishes vary, depending upon model.
PREPARING FOR INSTALLATION
Unpack and
inspect fan carefully to be certain all contents are included.
Turn off power at fuse box to avoid possible electrical shock.
Use metal
outlet box suitable for fan support (must support 35 lbs).
Before attaching fan to outlet box, ensure the outlet box is securely fastened
by at least two points to a structural ceiling member (a loose box will cause
the fan to wobble).
MOUNTING BRACKET INSTALLATION
Loosen but don’t
remove the screws at the bottom of canopy; remove the mounting bracket from
the canopy.
Install mounting bracket to outlet box in ceiling using
the screws and washers provided with the outlet box.
NORMAL DOWNROD OPTION
Remove clamp pin (1) and cross pin (2) from downrod (3).
DOWNROD INSTALLATION
Loosen (but do not remove) the set screws from the down rod coupling. Place
downrod assembly into canopy and canopy hole cover (4). Insert motor wires
through the downrod and insert the downrod into the downrod coupling. Make
sure to align the hole in the downrod with the hole in the downrod coupling.
Install cross pin (1) removed in step 5 through coupling and downrod. Insert
clamp pin (2) into cross pin until it snaps into place. Tighten set screws (3)
in coupling. SEE APPENDIX FOR ALTERNATE INSTALLATION OPTIONS IN PAGE 19.
MOUNTING
Carefully lift
fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1)
engages the ridge on the mounting bracket (2). This will allow for hands free
wiring.With bracket holding fan assembly, make electrical connections using the following step for wiring instructions.
WIRING OPTIONS
SECURE TO CEILING
Loosen the 2 screws on the bottom of mounting bracket but do not remove them. Raise the canopy up and align the keyholes on the bottom of the canopy with the 2 screws on the bottom of mounting bracket. Rotate the canopy until both screws from the mounting bracket drop into the slot recesses. Tighten screws securely.
The
inside canopy cover ring (1) has two keyhole slots that allow it to be mounted
onto the screw heads on the two protruding screws from the mounting bracket.
Slide the canopy cover ring up the downrod, and allow the two protruding screw
heads from the mounting bracket to go into the keyhole slots on the canopy
cover ring. Once engaged, twist the canopy cover ring to lock it onto the
screw heads. Note: Some adjustment of the screws from the mounting bracket may
be necessary to allow the canopy cover ring to attach to the screw heads in
the appropriate manner:
- Loosening of the screw heads may be necessary to allow the canopy cover ring to fit onto the screws from the mounting bracket.
- If the canopy is still loose after installing the canopy cover ring, the canopy cover ring may need to be removed and the mounting bracket screws tightened slightly to allow a more snug fit of the canopy, when the canopy cover ring is installed.
BLADE INSTALLATION
Attach blade brackets to blades using the blade bracket screws (1) and fabric
washers (2).
LIGHT FIXTURE INSTALLATION
Remove the three pre-installed screws from the ceiling fan’s light kit and
save for later use. Find the wire plugs from the light kit and from the motor
and slide together.
Connect the blue wire from the switch housing, to the black wire from the
light kit, and the white wire from the switch housing to the white wire from
the light kit. Attach light kit to the switch housing using three small screws
you previously removed, aligning the notch in the light kit with the reverse
switch found inside the switch housing.
LIGHT FIXTURE INSTALLATION
Unscrew and remove the finial (1), decorative cap
(2), nut (3), and rubber/metal washer (4) from the bottom of the light kit.
Install the bulbs (included).
Install the
glass (5) onto the light kit and tighten the washer (4) and nut (3) onto the
bottom of glass. Make sure the ceiling fan pull chain is threaded through the
side hole in the bottom of the glass. Place decorative cap (2) over the bottom
of glass and secure by tightening decorative finial (1).
Note : (6) Make sure the side hole on the decorative cap lines up with
the side hole on the bottom of the glass so that the fan pull chain operates
smoothly.
Assemble
decorative fob and extension chains from hardware bag to fan pull chains by
inserting end of chain into chain coupling. Confirm chains are held by lightly
pulling both chains in coupling.
Appendix for alternate installation options
EXTENDED DOWNROD OPTION (from page# 20)
EXTENDED DOWNROD OPTION
Loosen the downrod ball (1)
from downrod (2) by removing the screw (3). Slide downrod ball (1) off of
downrod and remove pin (4).
Re-
install pin into extended down rod, and slide down rod ball up to the top of
the down rod. Re-install set screw to secure ball to downrod. Note: Some
extended down rods have a pre-drilled set-screw hole. If a pre-drilled hole is
present in the extended down rod, tighten the set screw into the pre-drilled
hole in the extended down rod. If no pre-drilled hole exists in the extended
down rod, tighten the set screw against the down rod to secure the down rod
ball. PROCEED TO PAGE 9, STEP 6.
OPERATION AND MAINTENANCE
Operation
Turn on the power and check operation of fan. The pull chain controls the fan
speeds as follows: 1 pull – high; 2 pulls – medium; 3 pulls – low; 4 pulls –
off.
Speed settings for warm or cool weather depend on factors such as room size,
ceiling height, number of fans and so on.
The slide switch controls direction, forward or reverse.
Warm weather/down position – (Forward) Fan turns counterclockwise direction. A
downward air flow creates a cooling effect as shown in illustration A.
This allows you to set your air conditioner on a higher temperature setting
without affecting your comfort.
Cool weather/up position – (Reverse) Fan turns clockwise direction. An upward
airflow moves warm air off the ceiling area as shown in illustration B.
This allows you to set your heating unit on a lower setting without affecting
your comfort.
NOTE: Turn off and wait for fan to stop before changing the setting of the
forward/reverse slide switch.
Maintenance
-
Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year.
Make sure they are secure. -
Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning.
This could damage the motor, or the wood, or possibly cause electrical shock. -
Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer coating to minimize discoloration or tarnishing.
-
There is no need to oil your fan. The motor has permanently lubricated bearings.
TROUBLESHOOTING GUIDE
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, please consult with your qualified electrician and do not attempt any electrical repairs yourself.
| TROUBLE | SUGGESTED REMEDY |
|---|---|
| 1. If fan does not start | 1. check main and branch circuit fuses or circuit breakers. |
2. check wire connections as performed in step #9 or #10 of installation.
CAUTION: Make sure main power is turned off.
3. Make sure forward/reverse switch is firmly in up or down position.
Fan will not operate when switch is in the middle.
4. If the fan still will not start, contact a qualified electrician.
Do not attempt to troubleshoot internal electrical connections yourself.
2. If fan sounds noisy:| 1. check to make sure all screws in motor housing are snug (not over tightened).
2. check to make sure the screws which attach the fan blade holder to the
motor are tight.
3. Some fan motors are sensitive to signals from Solid State variable speed
controls.
DO NOT USe a Solid State variable speed control.
4. Allow “break-in” period of 24 hours. Most noises associated with a new fan
will disappear after this period.
3. If fan wobbles:| All blades are weighed and grouped by weight. Natural woods vary in density which could cause the fan to wobble even though all blades are weight-matched. The following procedures should eliminate most of the wobble. check for wobble after each step.
1. check that all blades are screwed firmly into blade holders.
2. check that all blade holders are tightened securely to motor.
3. Make sure that canopy and mounting bracket are tightened securely to
ceiling joist.
4. If blade wobble is still noticeable, interchanging two adjacent (side by
side) blades can redistribute the weight and possibly result in smoother
operation.
4. If light does not work:| 1. check to see that the wire connections in the
switch housing are connected.
2. check for faulty light bulbs.
3. If light kit will still not operate, contact a qualified electrician for
assistance.
WARRANTY
This Westinghouse Lighting Fan offers a Limited Lifetime Warranty to the
original owner against defects in material and workmanship.
This warranty is in lieu of all other warranties expressed or implied.
Westinghouse Lighting will repair or replace the parts needed, and/or, replace
the ceiling fan, if the defective is due to faulty materials or workmanship.
Years 1 & 2 – Westinghouse Lighting will repair or replace this ceiling fan.
After Year 2 – Warranty is limited to the motor.
This warranty does not cover acts of nature such as lightning damage, or
corrosion and discoloration of components, nor does it cover damages caused
through abuse, improper installation, surges in electric current, or acts of
third parties. This warranty does not cover broken glass after installation.
If this ceiling fan fails during the warranty period, return defective product
to seller. Warranty terms and conditions of sellerr apply.
If replacement product is not available through seller, please contact
www.westinghouselighting.com/contact-us.
PARTS LIST
| Description
---|---
1| Mounting Bracket
2| Blade Bracket
3| Blade
4| Glass
5| Fan Speed Switch
6| Light Control Switch
7| Capacitor
8| Hardware Pack
ETL-ES-Albert-WH22
Westinghouse Lighting,
Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
and Westinghouse are trademarks of
Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All Rights Reserved.
Made in China
Documents / Resources
|
Westinghouse ETL-ES-Albert-WH22 52 Inch Five Blade Indoor Ceiling
Fan
[pdf] Owner's Manual
ETL-ES-Albert-WH22, ETL-ES-Albert-WH22 52 Inch Five Blade Indoor Ceiling Fan,
52 Inch Five Blade Indoor Ceiling Fan, Five Blade Indoor Ceiling Fan, Blade
Indoor Ceiling Fan, Indoor Ceiling Fan, Ceiling Fan, Fan
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>