DENALI ARH1702B-00 20V Cordless Rotary Hammer Kit Instruction Manual

DENALI ARH1702B-00 20V Cordless Rotary Hammer Kit

WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
• Your risk from these exposures varies, depending upon how often this type of work is done. To reduce the exposure to mentioned chemicals:
  • Work in a well-ventilated area.
  • Work with approved safety protective equipment (PPE), such as dust masks that are specially designed to filter out microscopic particles.
  • Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water.
  • Do not allow dust to get into your mouth or eyes or to rest on the skin as this may promote absorption of harmful chemicals.

Safety Warnings

General power tool safety warnings

WARNING
Read all safety warnings and all instructions.

Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
2. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Battery tool use and care

1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
3. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Service
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Hammer safety warnings

Safety instructions for all operations

1. Wear ear protectors. Exposure to noise can cause hearing loss.
2. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Safety instructions when using long drill bits with rotary hammers

1. Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
2. Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

Additional safety warnings

1. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body is unstable and may lead to loss of control.
2. Keep handles dry, clean and free from oil and grease. Slippery hands cannot safely control the power tool.
3. Develop a periodic maintenance schedule for your power tool. When cleaning a power tool be pinchel nor so ely guard learn sortio maybe improperly mo inter l wires aying misplased ars gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.
4. To reduce the risk of explosion, electric shock and property damage, always check the work area for hidden gas pipes, electrical wires or water pipes.
5. Hold the power tool securely. When tightening and loosening the screws/bolts be prepared for temporary high torque reactions.

Vibration and noise reduction
To reduce the impact of noise and vibration emission, limit the time of operation, use low-vibration and low-noise operating modes as well as wear personal protective equipment (PPE).

Take the following points into account to minimise the vibration and noise exposure risks:

• Only use the power tool as intended by its design and these instructions.
• Ensure that the power tool is in good condition and well maintained.
• Use correct attachments for the power tool and ensure they are in good condition.
• Keep a tight grip on the handles/gripping surfaces.
• Maintain the power tool in accordance with these instructions and keep it well lubricated (where appropriate).
• Plan the work schedule to spread any high vibration tool use across a longer period of time.

Residual risks
Even if you are operating this power tool in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this power tool:

• Health defects resulting from vibration emission if the power tool is used over long periods of time or not adequately managed and properly maintained.
• Injuries and damage to property due to broken attachments or the sudden impact of hidden objects during use.
• Hearing loss due to prolonged exposure to noise.

Description of Symbols

The symbols and abbreviations below are used in these instructions and on the labels on the power tool. Get familiarized with the meaning of these symbols and abbreviations before using the power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Signal words

• DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
• WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
• CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE is used to address practices not related to personal injury.

Symbol explanation

FCC-Supplier’s Declaration of Conformity

• Unique Identifier
  ARH1702B-00 – Amazon Brand – Denali by SKIL 20V Rotary Hammer

• Responsible Party
  Amazon.com Services LLC.

• U.S. Contact Information
  410 Terry Ave N. Seattle, WA 98109 USA

• Telephone Number
  206-266-1000

FCC Compliance Statement

1. This device complies with Part 1 S of the FCC Rules. Operation is subject to the following two conditions:
2. this device may not cause harmful interference, and
3. this device must accept any interference received, including interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Danger:
People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker.

Canada IC Notice

This Class B digital apparatus complies with Canadian CAN ICES-003(8) / NMB-003(8) standard.

Specifications

• Model number ARH1702B-OO
• Rated voltage 20 V ==
• Rated no-load speed n 0-900 rpm
• Impact rate 0-5000 ipm
• Impact force 1 Joule
• Chuck type SDS-plus chuck
• Drilling capacity
  • In metal: 03/8″ (010 mm)
  • In masonry: 01/2″ (012 mm)
  • In wood: 01/2″ (012 mm)
• Recommended working temperature +14 °F to +104 °F (-10 °c to +40 °C)
• Recommended storage temperature + 32 °F to +104 °F (0 °C to +40 °C)
• Recommended charging temperature +41 °F to +104 °F (+5 °C to +40 °C)
• Net weight approx. 3 lbs (1.37 kg) (without battery)
• Dimensions (W x H x D) approx. 10.4 x 7 .5 x 2. 7″ (26.3 x 19 x 6.9 cm) (without battery)

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.

Scan QR Code below with your phone camera or QR reader:

If you need help with your Denali product, please use the website or number below.

• amazon.com/gp/help/customer/contact-us
• +1 877-485-0385

amazon.com/denali

MADE IN CHINA.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>