VEVOR LCWB90 Portable Workbench User Manual

: June 14, 2024
: VEVOR

Table of Contents

VEVOR LCWB90 Portable Workbench
GENERAL SAFETY RULES
WORKPLACE
MAINTENANCE
PRODUCT PARAMETER
STRUCTURE AND PART NAME
ASSEMBLE STEPS
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VEVOR LCWB90 Portable Workbench

VEVOR-LCWB90-Portable-Workbench-PRODUCT

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

GENERAL SAFETY RULES

IMPORTANT: carefully read the instructions in this manual as well as the general safety instructions before using this tool.

Before using the tool, read the instruction book carefully.

WARNING! Read the instructions and use or operate without following the instructions listed below will result in deformation, inflexible movement, loss of bearing weight or serious injury.

WORKPLACE

Keep the workplace clean and bright. A messy and dark place can cause accidents.
Do not expose the workbench to rain or a wet environment.
Pay attention to whether the ground is smooth when working outdoors to prevent tilt and collapse.

PORTABLE WORKBENCH USE AND PRECAUTIONS

Check whether the screws and nuts are tightened to prevent collapse during use.
When preparing for work, check whether the universal wheel is locked to prevent sliding during use.
Use safety devices. Always wear gloves.
Maintain the portable workbench, check the installation deviation of the moving parts, whether it is stuck, screw damage and other conditions affecting the operation of the portable workbench, such as damage, portable workbench must be repaired before use, many accidents caused by poor maintenance.

MAINTENANCE

Send your portable workbench to professional maintenance personnel, must use the same spare parts for replacement, this will ensure the safety of use after maintenance.

PRODUCT PARAMETER

Model	LCWB90

Length

|

700

|

mm

Width

|

600

|

mm

Maximum Adjustable Height

|

900

|

mm

Medium Adjustable Height

|

850

|

mm

Minimum Adjustable Height

|

800

|

mm

Load Limit

|

100

|

lbs

G.W|

25.4

|

kg

N.W|

21.9

|

kg

STRUCTURE AND PART NAME

VEVOR-LCWB90-Portable-Workbench-FIG-1 VEVOR-
LCWB90-Portable-Workbench-FIG-2

Name of Parts

Platform
Panel
WB90 Column
WB90 Column
Bulkhead
Bower Bulkhead
Universal Wheel
Directional Wheel
M6 Flange Nut
M6 Carriage Screws
M8 Hex Socket Screws
M8 Flange Nuts
M8 Hexagon Socket
Countersunk Head Screws

ASSEMBLE STEPS

STEP. 1
Fix 7 (universal wheel) and 8 (universal wheel) to 6 (lower divider) with 11 (M8 hex socket screws) and 12 (M8 flange nut).2. The tool is intended for household and professional use.
STEP. 2
Use 10 (M6 carriage screws) and 9 (M6 flange nuts) to make 4 (WB90 column 2) fixed in 6 (lower partition) around.
STEP. 3
Fix 5 (partition) into 4 (WB90 column 2) with 10 (M6 carriage screws) and 9 (M6 flange nuts).
STEP. 4
Fix 3 (WB90 Post 1) on the remaining two holes of 4 (WB90 Post 2) with 10 (M6 carriage screws) and 9 (M6 flange nuts).
STEP. 5
Fix 2 (panel) into 3 (WB90 column 1). Put 10 (M6 carriage screw) and 9 (M6 flange nut) into the top two holes of 3 (WB90 column 1) and tighten.
STEP. 6
Put 1 (bench) on 2 (panel), put 13 (M8 hexagonal countersunk head screw) into 1 (bench) four holes to tighten, and make it fixed.

ADJUST THE HEIGHT

The maximum height is 900mm. As shown in the figure: First, align the hole positions in 1.2.3 of Figure 3 (WB90 column 1) and 4 (WB90 column 2), then insert 10 (M6 carriage screws) and 9 (M6 flange nuts) into the hole 1.2.3 and tighten them.
Medium height 850mm as shown in Figure 1: First align hole 3 (WB90 column 1) and hole 4 (WB90 column 2) 2.3.4 one by one, then insert 10 (M6 carriage screws) and 9 (M6 flange nuts) into hole 2.3.4 and tighten it.
Minimum height of 800 as shown in Figure 3. First, align holes 3 (WB90 column 1) and 4 (WB90 column 2) 3.4.5 one by one, then insert 10 (M6 carriage screws) and 9 (M6 flange nuts) into hole 3.4.5 and tighten them.