TELTONIKA FMB225 Tracker Sim Dual Waterproof Owner’s Manual

FMB225
WATERPROOF DUAL-SIM TRACKER
WITH RS232, RS485 INTERFACES
Quick Manual v1.4

KNOW YOUR DEVICE

PINOUT

V DC).
2| AIN 1| Analog input, channel 1.
Input range: 0-30 V DC.
3| RS232 – RX| Input for data receive through RS232
4| RS232 – TX| Output for data transmit through RS232
5| DIN 1| Digital input, channel 1.
6| INPUT 6| TX EXT (LVCAN – TX).
7| GND (-)| Ground pin. (10-30) V DC
8| DOUT 1| Digital output, channel 1. Open collector output.
Max. 0,5 A DC
9| RS485 – A| Signal A wire for RS485
10| RS485 – B| Signal B wire for RS485
11| 1WIRE DATA| Data for 1–Wire devices.
12| INPUT 5| RX EXT (LVCAN – RX).

WIRING SCHEME

SET UP YOUR DEVICE

HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY

1. PARTLY CLOSED DEVICE You will receive your device partly closed.

2. COVER REMOVAL Gently remove top and bottom covers.

3. SIM CARD INSERT Insert SIM card as shown with PIN request disabled or read our Wiki¹ how to enter it later in Teltonika Configurator² . Make sure that Micro-SIM card cut-off corner is pointing outward from slot. SIM slot 1 is closer to PCB, SIM slot 2 is the top one.
   1  wiki.teltonika-gps.com/view/FMB225_Security_info
   2  wiki.teltonika-gps.com/view/Teltonika_Configurator

4. BATTERY CONNECTION
   Connect battery as shown to device. Position the battery in place where it does not obstruct other components.

5. ATTACHING COVER BACK
   After configuration, see “PC Connection (Windows)1”, attach device top and bottom cover back and press them twice to the full closure. 1 Page 7, “PC Connection (Windows)

6. COMPLETELY CLOSED DEVICE
   Make sure that product casing is closed correctly.

IMPORTANT!
This device has an IP67 casing with a two-phase closing, that ensures reliable protection and ease of use. Please make sure that product casing corner clips are fixed tightly and cable is connected to the device in order to maintain the degree of IP67 protection.

PC CONNECTION (WINDOWS)

1. Power-up FMB225 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED indications 1”.

2. Connect device to computer using Micro-USB cable or Bluetooth connection:
   • Using Micro-USB cable
   • You will need to install USB drivers, see “How to install USB drivers (Windows)2”
   • Using Bluetooth
   • FMB225 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named – “FMB225_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.

3. You are now ready to use the device on your computer.

1 wiki.teltonika-gps.com/view/FMB225_LED_status 
2 Page 6, “How to install USB drivers”

HOW TO INSTALL USB DRIVERS (WINDOWS)

1. Please download COM port drivers from here 1.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

1 teltonika.lt/downloads/en/FMB225/TeltonikaCOMDriver.zip

CONFIGURATION

At first FMB225 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator¹ software. Get the latest Configurator version from here². Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

1  wiki.teltonika-gps.com/view/Teltonika_Configurator
2  wiki.teltonika-gps.com/view/Teltonika_Configurator_versions

MS .NET REQUIREMENTS

Operating system| MS .NET Framework version| Version| Links
---|---|---|---
Windows Vista
Windows 7
Windows 8.1
Windows 10| MS .NET Framework 4.6.2| 32 and 64 bit| www.microsoft.com¹

1 dotnet.microsoft.com/en-us/download/dotnet- framework/net462

Downloaded Configurator will be in compressed archive.
Extract it and launch Configurator.exe. After launch software language can be changed by clicking ? in the right bottom corner.

Configuration process begins by pressing on connected device.

After connection to Configurator Status window will be displayed.
Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5 and etc. FMB225 has one user editable profile, which can be loaded and saved to the device.
After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

| Load from device – loads configuration from device.
---|---
| Save to device – saves configuration to device.
| Load from file – loads configuration from file.
| Save to file – saves configuration to file.
| Update firmware – updates firmware on device.
| Read records – reads records from the device.
| Reboot device – restarts device.
| Reset configuration – sets device configuration to default.

Most important configurator section is GPRS – where all your server and GPRS settings6 can be configured and Data Acquisition7   – where data acquiring parameters can be configured. More details about FMB225 configuration using Configurator can be found in our Wiki8.

1.  wiki.teltonika-gps.com/view/FMB225_Status_info
2.  wiki.teltonika-gps.com/view/FMB225_Status_info#GNSS_Info
3. wiki.teltonika-gps.com/view/FMB225_Status_info#GSM_Info
4. wiki.teltonika-gps.com/view/FMB225_Status_info#I.2FO_Info
5.  wiki.teltonika-gps.com/view/FMB225_Status_info#Maintenance
6.  wiki.teltonika-gps.com/index.php?title=FMB225_GPRS_settings
7.  wiki.teltonika-gps.com/index.php?title=FMB225_Data_acquisition_settings
8.  wiki.teltonika-gps.com/index.php?title=FMB225_Configuration

QUICK SMS CONFIGURATION

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:

Note: Before SMS text, two space symbols should be inserted.
GPRS SETTINGS:

1. 2001 – APN

2. 2002 – APN username (if there are no APN username, empty field should be left)

3. 2003 – APN password (if there are no APN password, empty field should be left)
   SERVER SETTINGS:

4. 2004 – Domain

5. 2005 – Port

6. 2006 – Data sending protocol (0 – TCP, 1 – UDP)

DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION:

VEHICLE MOVEMENT
will be detected by accelerometer IGNITION
will be detected by vehicle power voltage between 13,2 – 30 V

DEVICE MAKES A RECORD ON STOP IF:

1 HOUR PASSES
while vehicle is stationary and ignition is off

RECORDS SENDING TO SERVER:

EVERY 120 SECOND
it is sent to the server If device has made a record

DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:

|
---|---
PASSES
300 seconds| VEHICLE DRIVES
100 meters
|
VEHICLE TURNS
10 degrees| SPEED DIFFERENCE
between last coordinate and current position is greater than 10 km/h

After successful SMS configuration, FMB225 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.
1  wiki.teltonika-gps.com/view/Teltonika_Configurator
2  wiki.teltonika- gps.com/view/Template:FMB_Device_Family_Parameter_list

MOUNTING RECOMMENDATIONS

CONNECTING WIRES

• Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
• The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
• If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
• Wires cannot be connected to the board computers or control units.

CONNECTING POWER SOURCE

• Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in 5 to 30 minutes period.
• When module is connected, measure voltage again to make sure it did not decrease.
• It is recommended to connect to the main power cable in the fuse box.
• Use 3A, 125V external fuse.

CONNECTING IGNITION WIRE

• Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
• Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
• Check if power is still available when you turn off any of vehicles devices.
• Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.

CONNECTING GROUND WIRE

• Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
• If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
• For better contact scrub paint from the spot where loop is going to be connected.

MOUNTING RECOMMENDATIONS WITH U-TYPE CABLE

DEVICE FASTENING

• Locate the battery in your vehicle. If present remove the battery cover to access the battery.
• You can use a double-sided tape to attach the device on the battery as well as a fastening straps to mount it anywhere next to the battery. Please make sure, that the GNSS antenna and LEDs indicators are facing up Figure 13.

CONNECTING POWER WIRE
Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.
CONNECTING GROUND WIRE
Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.

LED INDICATIONS

NAVIGATION LED INDICATIONS

Device is not working or Device is in sleep mode
Blinking fast constantly| Device firmware is being flashed

STATUS LED INDICATIONS

BASIC CHARACTERISTICS

MODULE

GNSS

GNSS| GPS, GLONASS, GALILEO, BEIDOU,
QZSS, AGPS
---|---
Receiver| Tracking: 33
Tracking sensitivity| -165 dBM
Position Accuracy| < 2.5 CEP
Velocity Accuracy| < 0.1 m/s (within +/- 15% error)
Hot start| < 1 s
Warm start| < 25 s
Cold start| < 35 s

CELLUAR

MHz
Data transfer| GPRS Multi-Slot Class 12 (up to 240
kbps), GPRS Mobile Station Class B
Data support| SMS (text/data)

POWER

gps.com/view/FMB225_Sleep_modes#Ultra_Deep_Sleep_mode)1)
At 12V < 6,5 mA (Deep Sleep1)
At 12V < 7 mA (Online Deep Sleep1)
At 12V < 12 mA (GPS Sleep1)
At 12V < 38 mA (nominal with noload)
At 12V < 1.0 A Max. (with full Load/Peak)

BLUETOOTH

Supported
peripherals| Temperature and Humidity sensor, Headset2, OBDII dongle3, Inateck
Barcode Scanner, Universal BLE sensors support

1  wiki.teltonika-gps.com/view/FMB225_Sleep_modes
2  wiki.teltonika- gps.com/view/How_to_connect_Bluetooth_Hands_Free_adapter_to_FMB_device
3  wiki.teltonika- gps.com/view/How_to_connect_OBD_II_Bluetooth_Dongle_to_FMB_device

INTERFACE

PHYSICAL SPECIFICATION

Dimensions| 70,5 x 67,0 x 25,6 mm (L x W x H)
85,0 x 67,0 x 25,6 mm (L x W x H)
(length with connector socket)
---|---

OPERATING ENVIRONMENT

-20 °C to +35 °C for 6 months

FEATURES

gps.com/view/FMB225_Features_settings#Eco.2FGreen_Driving), Over Speeding detection, Jamming detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Immobilizer, iButton Read Notification, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip4
Sleep modes| GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep
Configuration and
firmware update| FOTA Web, FOTA, Teltonika Configurator (USB, Bluetooth), FMBT mobile application (Configuration)
SMS| Configuration, Events, DOUT control, Debug
GPRS commands| Configuration, DOUT control, Debug
Time Synchronization| GPS, NITZ, NTP
Fuel monitoring| LLS (Analog), LV-CAN200, ALLCAN300, OBDII dongle, CANCONTROL, OBDII dongle
Ignition detection| Digital Input 1, Accelerometer, External Power Voltage, Engine RPM (CAN Adapters, OBDII dongle)

ELECTRICAL CHARACTERISTICS

CHARACTERISTIC
DESCRIPTION| VALUE
---|---
MIN.| TYP.| MAX.| UNIT
Supply Voltage (Recommended Operating Conditions)| +10| | +30| V
DIGITAL OUTPUT (OPEN DRAIN GRADE)| | | |
Drain current (Digital Output OFF)| | | 120| µA
Drain current (Digital Output ON, Recommended Operating Conditions)| | 0.1| 0.5| A
Static Drain-Source resistance (Digital Output ON)| | 400| 600| mΩ
DIGITAL INPUT| | | |
Input resistance (DIN1)| 47| | | kΩ
Input voltage (Recommended Operating Conditions)| 0| | Supply
voltage| V
Input Voltage threshold (DIN1)| | 7.5| | V
ANALOG INPUT| | | |
Input voltage (Recommended Operating Conditions), Range 1| 0| | +10| V
Input resistance, Range 1| | 38.45| | kΩ
Measurement error on 12V, Range 1| | 0.9| |  %
Additional error on 12 V, Range 1| | 108| | mV
Measurement error on 30 V, Range 1| | 0.33| |  %
Additional error on 30 V, Range 1| | 88| | mV
Input Voltage (Recommended Operating Conditions), Range 2| 0| | +30| V
Input resistance, Range 2| | 150| | kΩ
Measurement error on 12 V, Range 2| | 0.9| |  %
Additional error on 12 V, Range 2| | 108| | mV
Measurement error on 30 V, Range 2| | 0.33| |  %
Additional error on 30 V, Range 2| | 88| | mV
OUTPUT SUPPLY VOLTAGE 1-WIRE| | | |
Supply voltage| +4.5| | +4.7| V
Output inner resistance| | 7| | Ω
Output current (Uout > 3.0 V)| | 30| | mA
Short circuit current (Uout = 0)| | 75| | mA

SAFETY INFORMATION

This message contains information on how to operate FMB225 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

• The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10…+30 V DC.
• To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
• When connecting the 2×6 connector wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.
• Before unmounting the device from the vehicle, the 2×6 connector must be disconnected. The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 62368-1 standard.
• The device FMB225 is not designed as a navigational device for boats.

| Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
---|---
| All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
| The device must be connected only by qualified personnel.
| The device must be firmly fastened in a predefined location.
| The programming must be performed using a PC with autonomic power supply.
| Installation and/or handling during a lightning storm is prohibited.
| The device is susceptible to water and humidity.
| Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
****| Battery should not be disposed of with general household waste. Bring damaged or worn-out batteries to your local recycling center or dispose them to battery recycle bin found in stores.

CERTIFICATION AND APPROVALS

| This sign on the package means that it is necessary to read the User‘s Manual before your start using the device. Full User‘s Manual version can be found in our Wiki1.
1 wiki.teltonika-gps.com/index.php?title=FMB225
---|---
| Hereby, Teltonika declare under our sole responsibility that the above described product is in conformity with the relevant Community harmonization: European Directive 2014/53/EU (RED).
| The RoHS1 is a directive regulating the manufacture, import and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use 10 different hazardous materials (to date).
| UK Conformity Assessed (UKCA) marking is a conformity mark that indicates conformity with the applicable requirements for above described products sold within Great Britain.
| The standard aims to provide users more detailed information than vague marketing terms such as waterproof.
| For more information, see the ANATEL website www.anatel.gov.br
This equipment is not entitled to protection against harmful interference and must not cause interference in duly authorized systems.
****| This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
| E-Mark and e-Mark are the European conformity marks issued by the transport sector, indicating that the products comply with relevant laws and regulations or directives. Vehicles and related products need to go through the E-Mark certification process to be legally sold in Europe.
| REACH addresses the production and use of chemical substances, and their potential impacts on both human health and the environment. Its 849 pages took seven years to pass, and it has been described as the most complex legislation in the Union’s history and the most important in 20 years.
It is the strictest law to date regulating chemical substances and will affect industries throughout the world.

DECLARATION OF IMEI ASSIGNMENT
The IMEI number is used by a GSM network to identify valid devices and therefore can be used for stopping a stolen phone from accessing that network. For example, if a mobile phone is stolen, the owner can call their network provider and instruct them to blacklist the phone using its IMEI number. This renders the phone useless on that network and sometimes other networks too, whether or not the phone’s subscriber identity module (SIM) is changed.
CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki2.
2 wiki.teltonika-gps.com/view/FMB225Certification%26_Approvals

WARRANTY

We guarantee our products 24-month warranty 1 period.
All batteries carry a 6-month warranty period.
Post-warranty repair service for products is not provided.
If a product stops operating within this specific warranty time, the product can be:

• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfilling the same functionality
• Replaced with a different product fulfilling the same functionality in case of EOL for the original product

1  Additional agreement for an extended warranty period can be agreed upon separately.

WARRANTY DISCLAIMER

• Customers are only allowed to return products as a result of the product being defective, due to order assembly or manufacturing fault.
• Products are intended to be used by personnel with training and experience.
• Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance or inadequate installation – not following operating instructions (including failure to heed warnings) or use with equipment with  which it is not intended to be used.
• Warranty does not apply to any consequential damages.
• Warranty is not applicable for supplementary product equipment (i. e. PSU, power cables, antennas) unless the accessory is defective on arrival.
• More information on what is RMA1

1  wiki.teltonika-gps.com/view/RMA_guidelines

Quick Manual v1.4 // FMB225

Documents / Resources

| TELTONIKA FMB225 Tracker Sim Dual Waterproof [pdf] Owner's Manual
FMB225 Tracker Sim Dual Waterproof, FMB225, Tracker Sim Dual Waterproof, Dual Waterproof, Waterproof
---|---

References

• Download .NET Framework 4.6.2 | Free official downloads
• FMB225 - Wiki Knowledge Base | Teltonika GPS
• FMB225 Configuration - Wiki Knowledge Base | Teltonika GPS
• FMB225 GPRS settings - Wiki Knowledge Base | Teltonika GPS
• FMB225 Certification & Approvals - Wiki Knowledge Base | Teltonika GPS
• FMB225 Features settings - Wiki Knowledge Base | Teltonika GPS
• FMB225 LED status - Wiki Knowledge Base | Teltonika GPS
• FMB225 Security info - Wiki Knowledge Base | Teltonika GPS
• FMB225 Sleep modes - Wiki Knowledge Base | Teltonika GPS
• FMB225 Status info - Wiki Knowledge Base | Teltonika GPS
• FMB225 Status info - Wiki Knowledge Base | Teltonika GPS
• FMB225 Status info - Wiki Knowledge Base | Teltonika GPS
• FMB225 Status info - Wiki Knowledge Base | Teltonika GPS
• FMB225 Status info - Wiki Knowledge Base | Teltonika GPS
• Anatel — Agência Nacional de Telecomunicações

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>