Kruger Matz KM0511 2.0 Journey Active Floorstanding Speaker Owner’s Manual

June 14, 2024
Kruger Matz

Kruger Matz KM0511 2.0 Journey Active Floorstanding Speaker

Kruger-Matz-KM0511-2-PRODUCT

SAFETY INFORMATION

Read this instruction manual carefully before first use, and keep it for future reference.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user the presence of uninsulated, dangerous voltage, within the product enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user the presence of important operation and maintenance {servicing) instructions in the literature accompanying the appliance.

SAFETY INSTRUCTIONS

  1. DO NOT expose this appliance to humidity, water or any other liquid.
  2. The appliance should be connected to a power supply as per specification in the operating instructions or as marked on the appliance.
  3. Place the device in a properly ventilated place.
  4. Protect the device from extreme temperatures, sources of heat and direct sunlight.
  5. Clean the unit’s exterior periodically with a soft, slightly damp cloth. Never use chemical agents to clean this device.
  6. Disconnect this device from power supply if it is not going to be used for a long period of time.
  7. Do not disassemble the device. In case of damage, contact with an authorized service point for check-up/repair.
  8. Power cord protection: power-supply cords should be routed so that they are not likely to be pinched by items placed upon or against them. Pay particular attention to cords, plugs, and power sockets and the point where they exit from the appliance.

FRONT PANEL

  1. Display
  2. Play/pause key / Frequency scanning key
  3. Input selection
  4. USB port
  5. Bluetooth indicator
  6. Volume
  7. Volume+
  8. Previous/ Program select down
  9. Next I Program select up
  10. Tone button
  11. Standby button
  12. IR receiver
  13. Preset button
  14. INFO/MENU button
  15. Select buttonKruger-Matz-KM0511-2 \(1\)

Please note: not every button will work in each mode!

REMOTE CONTROL

  1. Standby button
  2. INFO/MENU button
  3. Play/pause key / Disconnect with currently connected device (BT mode)
  4. Previous
  5. Preset button
  6. DSP button UAZZ / PO P / HALL/ DISCO / 6 CLASSIC/ STADIUM/ CINEMA/ DSP OFF)
  7. Treble+
  8. Volume-
  9. Volume+
  10. Input selection
  11. Treble –
  12. Select button
  13. Next
  14. Mute button
  15. Bass –
  16. Bass+Kruger-Matz-KM0511-2 \(2\)

REAR PANEL DESCRIPTION

  1. DAB/FM Antenna socket
  2. Left audio input
  3. Right audio input
  4. Power on/off switch
  5. AC Power cord
  6. Speaker output
  7. Optical input
  8. Coaxial inputKruger-Matz-KM0511-2 \(3\)

SPEAKER CONNECTION

IMPORTANT : Make sure the equipment is turned OFF before making any connections.
Note: Be sure to match the speaker cord to the appropriate jacks on components: ,,+”to,,+”, and ,,-“to,,-“.

INFO/MENU OPERATION

In any mode, press and hold INFO/MENU button to enter MENU options. Note: in DAB and FM modes, there are numerous tabs in MENU options. In all the other modes, there is only System tab in MENU options. When not in DAB nor FM modes, after pressing and holding INFO/MENU button, the screen will display . Press SELECT button to enter System tab and display available categories.
Use:

  • ◄I► buttons to navigate through options
  • SELECT button to enter submenu/confirm
  • INFO/MENU button to go back to higher level menu

Note : currently chosen option will be marked with”*” symbol.

  1. TIME
    Press and hold INFO/MENU > “System” settings> ”Time” settings for:

    • Set date and time: press ◄/► button to change value; press SELECT button to confirm
    • Auto update: select from automatic update from any source, from DAB or FM radio or no automatic update.
    • Set 12/24 format enter to change time format (12 or 24 hour format)
    • Set date format: enter to change date format (day-month-year or month-day-year)
  2. SLEEP
    Press and hold INFO/MENU> “System” settings> “Sleep” settings. User can set sleep time: OFF/ 15 / 30 / 45 / 60 / 90 minutes (looped)

  3. BACKLIGHT
    Press and hold INFO/MENU> “System” settings> “Backlight” settings. User can set:

    • Timeout : set the time after which the display backlight will be dimmed – On (backlight constantly on) I 10 / 20 I 30 I 45 / 60 / 90 / 120 / 180 seconds
    • On level : set backlight level – high/ medium/ low
    • DIM level : set backlight level when on standby- high/ medium/ low
  4. LANGUAGE
    Press and hold INFO/MENU > “System” settings > “Language” settings. User can select appropriate system language.

  5. FACTO RY RESET
    Press and hold INFO/MENU> “System” settings> “Factory Reset” settings. Enter this option to restore factory settings; select appropriate No or Yes and press SELECT button to confirm.

  6. SW VERSION
    Press and hold INFO/MENU > “System” settings > “SW version” settings. Displays information on software version.

DAB MODE

  1. In DAB mode, press [SCAN/PLAY] button on the front panel, and the screen will show “Scanning … ” (automatic full-band search). After scanning, a found station will be played.
  2. Press and hold ◄/► button to select next/previous station.
  3. When in DAB mode, press INFO/MENU button to display information of DAB, e. g.: receiving signal strength, program type, frequency, transmission rate, etc.

Note: if the DAB signal is received, the device will automatically update the time and date (if the function is enabled in settings).
DAB settings:
In DAB mode, press and hold the INFO/MENU button to enter MENU options.
Press ◄ / ► button to navigate through options and/or press SELECT button to enter selected tab:

  • Full scan : enter to perform automatic DAB stations scan
  • Manual tune : enter to manually set DAB station frequency
  • DRC : set Dynamic Range Compression to off/ high / low
  • Prune : select Yes or No
  • System : as described in INFO/MENU OPERATION section

FM MODE

Automatic search
When in FM mode, press SCAN/PLAY button on the front panel to perform automatic station search. The screen shows “Scanning … “. When a station is found, the search is stopped and the station is played.
Manual search
When in FM mode, press and hold or press continuously ◄ / ► button to reach desired frequency.
When in FM mode, press INFO/MENU button to display information of FM radio station, e.g.: signal strength, program type, date, time, RDS.
FM stereo/single channel selection
Click the INFO/MENU button, to check the radio information. When the screen displays “Stereo” or “Mono”, press SELECT button to change. Press INFO/MENU button again to save and exit.
Note: Stereo mode is default. If the radio signal is weak it will be automatically switched to Mono. To eliminate noise change the audio settings to “Forced mono”.
FM settings:
In FM mode, press and hold the INFO/MENU button to enter MENU options.
Press ◄ / ► button to navigate through options and/or press SELECT button to enter selected tab:

  • Scan settings: choose between searching for only strong stations or all stations while performing frequency scanning
  • Audio settings: choose between Stereo allowed / Forced mono
  • System: as described in INFO/MENU OPERATION section

PRESET LIST

  1. In DAB/FM mode, select the radio frequency that you want to save to preset. Please note: in DAB, if there is no station transmitting on a manually chosen frequency, user will not be able to save the frequency to preset.

  2. Press and hold PRESET button. Press ◄/► button to select number on preset list you wish to save the station (1-10).

  3. Press SELECT button to save on chosen number.
    Note: the device can store up to 1 O DAB and 1 O FM radio stations presets

  4. To play a preset radio station, press the PRESET button, and use ◄/► button to select desired preset number you want to listen.

  5. Press SELECT button to confirm.

POWER MANAGEMENT

When there is no audio playing for 10 minutes, while in DAB/BT/USB/Optical/ Coaxial/AUX IN modes, the device will automatically enter into standby mode to save energy.
Note: the function is not available in FM mode!
BLUETOOTH
Prior to use Bluetooth connection, pair it with an external Bluetooth device, to play music through the speakers. Once the devices are paired, the speaker will automatically connect with the external device whenever it will be placed within operational range and both appliances will have Bluetooth function ON.
To pair the speaker with an external device:

  1. Turn the speaker ON. In Bluetooth mode, flashing BT indicator indicates that the Bluetooth device is not connected. The blue LED will start blinking, and the screen will display caption BLUETOOTH, signifying BT is on.
  2. Turn ON the Bluetooth on the external device.
  3. Search for other BT devices on your external device and pair it with the speakers. Input default password “0000” or “1234” if necessary.
  4. Once the devices are connected, the blue LED will be flashing constant light.

In Bluetooth mode, press and hold SCAN/PLAY or ►II button to disconnect with currently connected Bluetooth device.

SPECIFICATIONS

| KM0511| KM0512| KM0532
---|---|---|---
Power output (RMS)| 2x 60W| 2x80W| 2x 100 W
Frequency response| 50 Hz – 20 kHz| 36 Hz – 20 kHz| 38 Hz – 20 kHz
Power consumption| 150W| 250W| 300W
Impedance| 40
Sensitivity                                       89 dB| 91 dB
Input sensitivity| 500 mV
S/N| 70 dB
THO (1 kHz, 1 W)| 0,5%
Bass (100 Hz)| ±10 dB
Treble (10 kHz)| ±10 dB
Bluetooth| Yes
FM radio| Yes
Digital radio| DAB+ (band 111174,0-240,0 MHz)
Inputs| USB port, 2x RCA, optical, coaxial
Speaker| 1x 8″, 2x 4″, 1x 1″| 1x 8″, 2x 5″, 1x 1″| 2x 8″, 1x 6,5″, 1x 1″
Power supply                                                   220-240 V AC; 50/60 Hz

LEARN MORE
For more information on this device visit: www.krugermatz.com.
Read owner’s manual carefully before using your smartphone.
Visit www.krugermatz.com website for more products and accessories.
In case of any doubts or questions reach out to our Frequently Asked Questions section.
Lech pol Electronics Sp. z o.o. Sp.k. hereby declares that active floorstanding speaker set KM0511 / KM0512 / KM0532 is consistent with directive 2014/53/UE. Full text of the EU Declaration of Conformity is available at following Internet address: www.lechpol.eu.

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems} This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolir’lska 1, 08-400 Mietne.
www.krugermatz.com
Kriiger&Matz is a registered trademark

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals