ZOSI 4in1 Security Camera Instruction Manual
- June 14, 2024
- ZOSI
Table of Contents
ZOSI 4in1 Security Camera
Introduction
Thank you for purchasing this CCTV camera from ZOSI. This camera can work in
almost all light conditions, from daylight (as long as it is not directly
irradiated by the sun) to total darkness.
The camera is very sensitive to light and therefore can also use a minimum
beam of light to create an image of what you captured. When it’s in low light,
it is displayed as a black-and-white image.
In total darkness or near-total darkness, the camera uses built-in infrared
LEDs to illuminate the area in front of it. This light is invisible to the
human eye, even though you might notice a faint red glow coming from the side
front of the camera, which is a phenomenon normal.
During the day or in a well-lit environment, the function camera’s IR Cut
Filter can filter the lengths of waveform of light which is useless for
cameras at the end to provide a clear colour image.
Important Note: All jurisdictions have laws and specific regulations
relating to the use of cameras. Before using any camera for any purpose, it is
the buyer’s responsibility to be knowledgeable of all applicable laws and
regulations that prohibit or limit the use of cameras. And the buyer must also
comply with the laws and applicable regulations.
Warning: Changes not approved by the party compliance officer could
invalidate the user’s authority to operate the equipment.
Important safety instructions
- Make sure the product is installed correctly and fixed firmly.
- Do not operate it if the wires and terminals are exposed.
Choosing a location for this camera
To get an optimal effect from the camera, the place where you install the
cameras is fundamental. You need to consider the distance between the camera
and the subject to make sure get a good view of the areas in focus. Also think
about appropriate mounting locations (e.g., under the eaves of a roof is a
good choice) where it will not be an easy target for vandals or will be
affected by continuous light reflections from moving vehicles (which may cause
detection of the movement erroneously activated). There are numerous factors
to consider when choosing one location to mount the camera, not just where you
want to monitor it.
To mount the camera
- Place the camera where you want to mount it and mark the screw holes on its surface to fix them. Then, using the appropriate screws for the surface you are on prepare to stare at the camera. Screw the camera firmly into place.
- If you intend to mount the camera on a wooden surface, screw the camera directly onto it surface.
- If you intend to mount the camera on a masonry surface (brick, concrete or similar), it will have to use the included anchors.
Mounting the camera
The camera can be mounted on a flat, vertical surface using screws. The surface must have sufficient strength to support the camera. Materials such as hardwood, brick or brickwork are good options. You can mount the camera on a metal surface, but you will have to provide its mounting hardware.
Position the cables
- When setting the cable, please search to avoid wrapping it on objects with acute corners.
- Do not put the cable near electrical wires under tension. AC electricity will generate Radio “noise”, which can interfere with the camera signal.
- All cables and connectors must be adequately isolated. In the meantime, they should also be protected from moisture and from sunlight because they are not resistant to atmospheric agents.
Please note the model shown it is for illustrative purposes only.
Mounting the camera
- Use a screwdriver to loosen the screw, then rotate the camera.
- Loosen the screw, then adjust the elbow joint.
- Secure the neck of the stand with the mounting base, then rotate the stand by loosening the lock ring radial joint. Once in place, tighten the ring again.
Connection guide
Please note the model shown it is for illustrative purposes only.
OSD button
Change the camera mode via the OSD button when the camera is on. Press the button in the OSD menu
- Switch to AHD: Press the left button for 5 seconds
- Switch to TVI: Press the right button for 5 seconds
- Switch to CVBS: Press the up button for 5 seconds
- Switch to CVI: Press the button down for 5 seconds
MAIN MENU
Automatic exposure
- BRIGHTNESS
DAY-NIGHT
- MODE
White balance
- MODE
- INFRARED
- SMART IR
- RETURN RET#
VIDEO SETUP
Troubleshooting
- Q: Displaying video loss on my monitor where it should display the image?
- A: Check that the extension cable (power and video) is securely connected to the camera.
- Verify that the camera’s video output is securely connected to the input channel videos on the DVR.
- Verify that the power from the camera is securely connected to the power supply.
- If the camera mode does not match your DVR, there are two methods to adjust it.
- Press the “Down” button on the OSD joystick for five seconds if it still does not appear the image, continue to press the “Left”, “Right”, and “Up” buttons in sequence, each for five seconds. Until the signal matches his DVR.
- Make sure the camera has the same signal as the DVR. Use the OSD joystick to change the camera mode to match the video mode of the DVR.
Limited Warranty Terms and Conditions
ZOSI Communications warrants this product against defects in workmanship and all materials will be warranted for a period of one year from the date of original purchase. It is necessary to present the received as proof of purchase date for warranty validation. Any unit that results in defective during the indicated period will be repaired without charge for parts or labour. Replaced at ZOSI’s sole discretion. The end user is responsible for all shipping charges when you need to send the product to the ZOSI repair centre. The end user is responsible of all shipping costs when shipping the product from a country other than the country of origin. The warranty does not cover any incidental, incidental or consequential damages arising from the inability to use this product. The end user must take responsibility for any costs associated with the assembly or removal of this product caused by dealers or other people. This warranty applies only to the original purchaser of the product and is prohibited from transferring the product to third parties. It will void all warranties if unauthorized end users or third parties modify any component or abuse the tests or abuse the device. By law, some countries do not allow limitations on certain exclusions in this warranty. Where applicable by local laws, regulations and legal rights shall take precedence.
CONTACT
All rights reserved. No part of this publication may be reproduced by any
means without written permission from ZOSI. The information in this
publication is believed to be accurate in all respects.
ZOSI cannot assume responsibility for any consequences resulting from the use
thereof. The information contained herein is subject to change without notice.
Revisions or new editions to this publication may be issued to incorporate
such changes.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>