Fanttik Storm 10 Pro Cordless Vacuum Cleaner User Manual

Storm 10 Pro
User Manual
Stick Vacuum Cleaner

Please read this instruction manual carefully before use and keep it for future reference.
Thank you for choosing fanttik
Thank you for purchasing fanttik vacuum cleaner, This is stick vacuum cleaner with strong suction and electric mite brush

Caution

Safety Precautions

• Do not vacuum any liquids (such as water, cola).
• Do not vacuum any burning or smoking substances (such as unextinguished cigarette butts).
• When the vacuum is operating , do not touch any rotating parts (especially for children) to prevent injuries .
• Do not charge or store the vacuum near heat sources or in humid areas (such as by a heating radiator or in the bathroom).

Tips

• When the battery is low, it may take about 3～5 hours to get fully charged.
• When the vacuum is used for the first time, it is recommended to fully charge it before use.
• Brush nozzles can be used independently to clean dust from the vacuum, dust compartment, etc.

Cleaning Tips

• Rinse the filter at least once a month with tap water. For details please refer to Maintenance.
• To avoid any potential damage to the cleaner, make sure to dry it before operation after cleaning the washable parts (such as filter and roller).

Non-washable Parts（Vacuum cleaner, brushes with motors and brush roller with bearings）

| |
---|---|---
Vacuum Cleaner| Electric Auto-speed Floor Brush| Electric Mite Brush (excluding roller)

Washable Parts

| | ``|
---|---|---|---
Dust Compartment| Cyclone Assembly| Front Fan Filter| Mite Brush Roller

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE), Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
WARNING–To reduce the risk of fire, electric shock, or injury:

• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle charger, including charger plug, and charger terminals with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without filter in place.
• Turn off all controls before unplugging.
•  Always turn off this appliance before connecting or disconnecting motorized nozzle.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents.
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
• Have servicing performed by a qualified repair person using only identical replacement parts.This will ensure that the safety of the product is maintained.
• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care.
• In order to prevent burnout of the machine due to short circuit, please do not pour or spill water or other liquids into the machine.
• When using a new battery or using a battery for the first time after long-term storage, please fully charge the battery. When the machine is not used for a long time during storage, please make sure that it is charged and discharged at least once every three months. When your vacuum cleaner is fully charged and needs cleaning or maintenance, please unplug the power adapter in time, and do not pull the power line.
• When cleaning the vacuum cleaner, just wipe it with a dry cloth and do not use gasoline/lacquer thinner or other detergents that are easy to crack or discolor the housing.
• Please do not use or store the vacuum cleaner in unfavorable conditions such as high temperature and low temperature. It is recommended to use it indoor at the ambient temperature of 32°F-104°F (0°C-40°C). Please store it in a cool and dry place and keep it away from long-time sunlight exposure.
• If the fully charged vacuum cleaner cannot work, it shall be sent to the designated repair point for testing and repair. Please do not disassemble the machine without authorization.

Battery Pack and Charging

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
• Battery charging can only be performed at the ambient temperature between 32°F (0°C) and 104°F (40°C). Excessively high or low temperature may extend the battery charging time, and even damage the battery. The normal charging of this product takes about 3-5 hours, and it is best to perform 1-3 complete charging and discharging processes for the first use, so as to fully activate the battery.
• For use only with E-TEK ZD024M310100US Charger.
• For use only with Fanttik A015ZBP Battery pack.
• Waste battery packs shall be recycled safely and disposed rather than being thrown away.
• If the power cord of the power adapter is damaged, it must be replaced by a professional from the manufacturer’s local after-service department or similar departments to avoid dangers. Do not turn on the power supply of the vacuum cleaner during charging! Do not remove the battery pack when the vacuum cleaner is connected for charging!
• If the product is not used for a long time, it is recommended that the machine shall be completely charged and discharged once every 3 months or so to avoid the passivation of the battery electrodes due to prolonged non-use.
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
• Do not disassemble, strike, crush or expose the battery to fire.
• Do not leave in a high-temperature environment.
• Do not use the product if the battery shows signs of serious swelling.
• Do not use the product if the battery is exposed to water.

Transportation
It is recommended to transport the vacuum cleaner in its original packaging.
SAVE THESE INSTRUCTIONS
Household use only.

Overview

Vacuum Cleaner

Display

1. Charging Indicator
2. Battery Level Indicator
3. Dust Status Indicator
4. Suction Power Indicator
   • When charging, the charging indicator will flash, and power percent will appear on the display; When fully charged, the charging indicator will be solid on, then the display will be off after 5 minutes.
   • When operating, the suction power indicator will show the current suction level.
   • When the dust status indicator  is flashing, please clean the dust compartment so as not to affect the work efficiency.

Accessories List

Install

Installing the Accessories onto the Vacuum Cleaner Install the battery pack
Install along the battery slide rail, once you heard a “click”, then the installation is done. Remove Battery Pack
Hold the vacuum cleaner with one hand, hold the battery pack with the other hand and press the release button to remove the battery pack. At the same time, pull the vacuum cleaner forcefully in the direction shown in the picture to separate it from the battery. Install Docking Station

• The wall-mounted docking station needs to be installed in a cool and dry place that is near a power outlet but not exposed to direct sunlight.
• Use the appropriate mounting hardware for the type of wall to securely install the docking station.
• Make sure the installation area is clear of any pipes such as gas or water lines, and air ducts, electric wires and cables, or drainage lines.
• It is recommended to hire a professional to install the docking station and to use protective clothing, goggles, and other protective materials where necessary.
• Use a 6 mm drill to drill a hole in the wall and insert the wall plug into it. Align the hole on the charging dock with the one in the wall, and insert and tighten the screw.

Recommended Height At least 115 cm from the ground

Use

Battery Level Indicator
1 st power grid flashing: Battery level＜30%;
2 nd power grid flashing: 30%≤ Battery level ＜60%;
3 rd power grid flashing: Battery level≥ 60%;
All three power grids on: Fully charged.
Display
When charging, the power percent will appear; When fully charged, the display will be off after 5 minutes.
Precautions

1. When the vacuum is used for the first time, it is recommended to fully charge it before use.
2. When charging, the vacuum will stop operating and automati cally enter charging mode.
3. Vacuuming at turbo mode for a prolonged period will cause the battery to heat up, which increases charging time. Allow the vacuum to cool down for 30 minutes before charging it.

Charging Method
Charging the vacuum cleaner with the power supply directlyCharging the battery pack with the power supply directly Charge the docking station

Vacuum Usage

• Before vacuuming highly polished floors (wooden or polished tiles), check the floor attachment (especially the brush) for foreign objects to avoid scratching the floor.
• Before using the hand-held vacuum cleaner, make sure the dust compartment and battery pack are well installed.
• Do not block the exhaust port when vacuuming.
• For fine dust such as flour, vacuum cleaners can only be used for small amounts.
• Do not use the vacuum to vacuum sharp objects, small toys, pins, paper clips, etc., to avoid damage to the vacuum cleaner and the floor.
• When using this vacuum to clean dangerous areas such as stairs and windows, make sure to pay attention to personal safety.
• Do not place the vacuum on places (including tables, chairs) nor lean it against items to avoid damage caused by dropping or slipping.
• The movement of the vacuum’s brush may cause an uneven gloss on waxed floors. Wipe the floor with a damp cloth and polish it with wax.

Automatic Turn-off Feature

• If any rotating part becomes stuck, the vacuum may turn off automatically. Remove any trapped foreign objects and press the power button again, then it will resume use.
• The vacuum will automatically shut off if its motor enters overheat protection mode. Wait until the brush’s temperature returns to normal before resuming use.
• Because the battery pack is affected by the ambient temperature, the characteristics of the cell are quite different, when using in turbo mode, there is a chance of shut down when 5% (20%, 15%, 10%) battery is left, but it will not affect the normal use and  protection feature.

Electric Auto-speed Floor Brush
The floor brush uses low speed to efficiently suck up dirt when cleaning hard floors such as marble, tile and wood floors.The floor brush automatically increases the speed when cleaning on floor coverage such as short-pile carpets, sucking up dust deep in the carpet.
Electric Mite Brush
Suitable for cleaning ash mites on general fabrics, such as bed, mattress, knitting sofa and blankets. Crevice Nozzle
Suitable for cleaning narrow areas, such as corners of doors and windows, slideway, corners of wall, cars.![Fanttik Storm 10 Pro Cordless Vacuum Cleaner

• Crevice Nozzle](https://manuals.plus/wp-content/uploads/2023/11/Fanttik- Storm-10-Pro-Cordless-Vacuum-Cleaner-Crevice-Nozzle.jpg) Brush Nozzle
  Suitable for dust cleaning on the curtain, keyboard, ceiling, car, coffee table and other surfaces.

Daily Care & Maintenance

Product Maintenance
Cleaning the vacuum cleaner
Wipe the vacuum with a soft dry cloth.
Cleaning the dust compartment, front fan filter, and cyclone assembly.
Recommended to rinse at least once a month.

1. Before cleaning the dust compartment, disconnect the adapter and keep the vacuum turned off. Once the dust reaches the “MAX” mark, the vacuuming effect will be affected if continued to be used, so please empty it as soon as possible before use.

2. To empty the dust compartment, push the switch on the back of the vacuum cleaner to eject dust compartment and open the bottom cover to empty the dust.

3. Rotate to remove the dust compartment and front fan filter, pull out the cyclone assembly to rinse the parts.
   Note: do not use detergents, polishes, or air fresheners to clean the dustcompartment. Do not put the dust  compartment, front fan filter and cyclone assembly into the dishwasher to wash them.

4. To thoroughly dry the dust compartment, front fan filter and cyclone assembly, keep them in a ventilated or cool place for at least 24 hours after cleaning.

Note: do not dry the dust compartment, front fan filter and cyclone assembly in a tumble dryer, oven, microwave, or near an open fire.

Install the cyclone assembly, front fan filter and dust compartment

1. Align the safety clip on the cyclone assembly with the notch on the dust compartment, and push it all the way.
2. Handle facing out, press to the bottom.
3. Align the protruding clip on the vacuum to the appropriate notch on the dust compartment, and then lock the dust compartment by rotating it. (When rotating the dust compartment, make sure the back fan is ejected.)
4. Press the dust compartment, when you heard a click, then the installation is done. (Please be careful and do not be clamped when pressing.)

Cleaning Electric Auto-speed Floor Brush Bar
Please make sure the brush head has been separated from vacuum cleaner before cleaning the floor brush, to avoid personal injury caused by accidental start of the vacuum cleaner.

1. Place the floor brush facing you in the direction shown in the figure, and use a coin to turn the lock 90° counterclockwise to the unlocked position.
2. Rotate the end cap 40° to the position of opening and gently slide the brush bar away from the head.
3. Place the roller end cap at 40° to the side of the floor brush after cleaning, gently slide the roller through the brush head and rotate the end cap to the closed position. (Note: there are bearings in the drum, do not wash.)
4. Turn the lock 90° clockwise to the locked position to secure the drum.

Clean the mite brush
Before cleaning the motorized acarid-killing brush, make sure that the attachment has been detached from the vacuum to avoid personal injuries caused by accidentally turning on the vacuum.

1. With the side latch of the brush head facing your direction, use a coin to turn the latch counterclockwise until it comes off, then remove the roller from the motorized acarid-killingbrush.
2. Rinse and clean the roller, place the roller vertically and keep it in a ventilated or cool place for at least 24 hours to dry thoroughly.
3. When the roller is completely dry, install the motorized acarid-killing brush. With the side latch of the brush head facing your direction, use a coin to turn the latch clockwise into the locked position, while making sure the roller is in place.

Specifications

• Due to the continuous development of technology, the company reserves the right to make improvements to the products described in this manual (specification).
  The user manual is for reference only, and product specifications, accuracy and appearance are subject to change without notice.

Troubleshooting

If the vacuum is not working properly, please refer to the troubleshooting table below.
motorized brush head does not rotate.

1. If the brush head gets stuck, remove any foreign objects and continue to use it normally.
2. Please wait until the attachment temperature returns to normal before using it, if its motor entered overheating protection mode.
3. Please wipe the contact points of the attachment with a soft dry cloth if they are dirty and try again.

Fan does not rotate.

1. Low battery pack, please charge before use.
2. It entered overheating protection mode due to being used continuously for too long. Allow the vacuum to cool down, and restart it to continue using it.
3. The filter or the nozzle is clogged, please clean them regularly. After cleaning you can use the vacuum normally again.

The vacuum cleaner has reduced suction.

1. Dust compartment is full, and the filter is clogged. Empty the compartment and rinse them before using the vacuum again.
2. Attachment is stuck, please remove any foreign objects from the attachment.

Roller brush not working.

1. Built-in PTC rotation-blocking protection, need to restart after removing the foreign objects.

LED light indicating battery status does not light up while charging.

1. Check if the power supply is properly plugged in.
2. The battery is fully charged and battery pack went into sleep mode.

The battery charges slowly.

1. The battery temperature is too high or too low, please wait for the battery temperature to return to normal and then recharge the vacuum.

WARRANTY CARD

Your Warranty Includes

• 12-Month Coverage
  Within 12 months of purchase, we will provide timely and effective online after-sales service. We will repair or replace any defective product (due to manufacturing fault) within the warranty period.

How to Return Your fanttik Product

• Contact support@fanttik.com with your order number.
• We will issue you a return label for your return.
• Tear off the ‘Return Details’ page and fill in the details. Include this inside your return package.
• We will issue your replacement/refund on receiving the return package.

**support@fanttik.com
Return Details**
In order to process your return as quickly as possible, we require the following information. Please fill out this form and include it in your return package.

Purchase Name:|
---|---
Order Number:|
Date of Purchase:|
Your Email Address:|
Place of Purchase:|

If your purchase was fulfilled by Amazon, please use Amazon’s 30-day return service.
The warranty will not apply in cases of:
Failures caused by:

1. Use of a fanttik product which is not in accordance with the“Usage Restrictions”in the User Manual.
2. Use of a fanttik product for cleaning white ashes, sand and other non-household garbage.
3. Use of a fanttik product for decoration, ornament or cleaning in a commercial environment.
4. Use of a fanttik product for cleaning in an environment with special adsorption chemicals, metal or other microparticles.
5. Use of a fanttik product in an environment with corrosive objects.
6. Use of a fanttik product in an improper voltage supply environment.

www.fanttik.com
support@fanttik.com
METASEE LLC
5205 Broadway #634 Pearland Texas 77581
Made in China

Documents / Resources

| Fanttik Storm 10 Pro Cordless Vacuum Cleaner [pdf] User Manual
Storm 10 Pro Cordless Vacuum Cleaner, Storm 10 Pro, Cordless Vacuum Cleaner, Vacuum Cleaner, Cleaner
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>