Hcalory 5KW 12V Smart Heater User Manual

SMART HEATER

User manual

5KW 12V Smart Heater

Function:

Get rid of damage to the car caused by the sudden drop in temperature, improve the temperature Inside the car, and preheat the engine coolant to avoid engine wear at low temperatures. Conducive to car interior thawing, car start, and car glass defrost fog.

Internal Structure

Installation Position

Product Structure Diagram

Remote Control Operation Instructions

The remote control does not include the battery, please configure 1 *12V 23A battery
Working mode

1. In the gear mode, the gears can be set within the range of 1-10 gears.
2. In the temperature control mode, the setting temperature can be adjusted within the range of 8-36°C, and the gear of the control switch will change with the temperature in the cab. When the temperature rises or falls, the control switch will automatically adjust the operating gear to quickly reach the set temperature, so that the heater The operation of the heater is more intelligent and economic.
3. When there is a fault in the operation, the fault code will be displayed through the control switch display window ashing for a more accurate and intuitive find the fault.

Operating instructions.
On/off and mode switching:
Press [ ] to turn on the power in the off state; press button [ ] to turn off the power in the on state; press [ middle knob ] to switch the current gear/temperature control mode.
Gear adjustment:
Turn [knob] clockwise to run gear/temperature +1, maximum to 10 gears/36°C, turn [knob] counterclock-wise to run gear/temperature -1, minimum to 1 gear/8°C.
Basic setting:
After powering on, press and hold the [ ] key for 3s to enter the basic setting interface, the upper left corner shows the setting items, and the interface shows the specific data under the setting items.
FO: Current time
Fl:auto-start time
F2:Running time [atter auto-start] F3:Auto-start switch setting
F4:Language switch [Chinese (C), English (E), Russian (13)] F5:Temperature compensation
F6: tank oil volume (5-50L (switch unit 5L)] [display — on behalf of not monitoring the tank situation] F7: oil pump power [16/22/28/32UL (default is 22UL)] F8: Bluetooth switch
F9: automatic start/stop heater; (in automatic mode, when the cab temperature reaches the set temperature, it will automatically turn off after a 30s delay; when the cab temperature is lower than the set tempera-ture by 2°C, it will automatically turn on after 30s delay)
Press [Knob] to modify, and press [Knob] again to confirm the current data modification. Rotate [knob] to adjust the setting items, after all the adjustments are successful, long press [ ] for 3s to save all the basic settings
Engineering Mode:
Power on the state while holding down [ ][  **] 3s into the project mode, the upper right corner shows the current project, the interface shows the specific data under the project, and rotate the [knob] to adjust the project.
View data:
En00:Heater main board version number (scrolling display] En01:Fault code [see the following table for details] EnO•Case temperature
En03:Power supply voltage
En04:Heater operating gear
En05:Cab temperature
En06:Altitude [top left corner
En07:Pump oil enable En08:Remote control match
En09:Bluetooth match
Remote control matching:
Enter the En08 interface, the interface shows ‘Re”, long press the [knob] 3s to start matching, the screen shows “P1”, then tap the remote control “adjustment plus +” button, the screen shows “P2″ means ‘adjustment plus +” match successfully, P2, P3, P4 similarly, P4 automatically exit the project mode to return to the operating interface after a successful match, the specific key definitions are as follows P1: Adjust plus button; P2: Adjust minus button; P3: Mode switch button; P4: Switch on/off button. Clear the last remote control matching data: press and hold [ ] for 7s when power on self- test, the interface shows “CL( to start clearing when the interface shows “SUC” to clear successfully.
Pump oil mode:
Press and hold the (lower left pumping] key during the power-on self-test until the screen displays ‘-P-‘ after the pumping icon lights up, the display area starts 300s countdown to release the key, start pumping, countdown the end of the countdown automatically exit, this operation needs to be completed when the power is on, the power self-test is over and cannot be entered.
Fill up the tank:**
After the power is on, long press the [pump oil] key for 7s to fill up the interface tank display icon.
Bluetooth matching: Search and download the corresponding APP name “airHeaterBle” in IOS or Android APP store, then please follow the below step to connect and control the heater with a mobile phone.

1. Query the Bluetooth name: press [ ] [Knob] 3s at the same time after powering on, the screen displays ‘bLE’, and the Bluetooth version of the upper side of the screen displays the 6-digit character name (0-F).

2. Connect to the mobile phone via Bluetooth: Click on the Bluetooth symbol in the upper right corner, and find the corresponding local Bluetooth number: BYD + MAC address of the Bluetooth device + 4 digits from the controller(Refer to the picture above), then click on the Bluetooth number to connect;
   

3. Long press the [ ] to turn on/turn off the heater ;

4. Click the [ ] button to go to the settings screen, you can set the language(English/Chinese), and password, and click “save” to save the settings; After setting the password, adjust the switch to enter the engineering mode En09, the interface display “BLe- long press (knob] 3s, the upper right corner from flashing the original password to display the set password, the interface display changes to “SUC’, after the successful match automatically return to run Interface

5. Click “mode* button to switch the gear mode or temperature control mode, then Click “up +” “down “button to increase + or decrease- the level(leavel1-10) / temperature(8°C ~ 36°C);

6. Fault display: when the heater fails, it will display the fault code E-xx, see the following table for the type of fault.

whether the interfaces of the oil circuit are hanging wax or blocked.
0.00E+00| Lack of oil and stalling| Checking the fuel tank for lack of oil.
0.00E+00| Abnormal voltage| 1. check that the heater supply voltage type matches the actual vehicle voltage.
2. check that the supply voltage Is not higher than 32V or lower than 18V for the 24V version.
3. check that the supply voltage Is not higher than 18V or lower than 9V for 12V version.
4. check that the main harness connector is not loosely connected.
0.00E+00| Air outlet temperature sensor failure| 1. detecting whether the outlet air temperature sensor connector is loose and falsely connected.
2. failure of the outlet air sensor, replace the main board.
3. main board failure, replace the main board.
0.00E+00| Inlet air temperature sensor| Inlet air sensor failure, replacement of the motherboard.
0.00E+00| Oil pump abnormality| 1. check the oil pump plug for loose false connections.
2. check the main wiring harness for disconnection.
3. oil pump fails, replace the oil pump.
0.00E+00| Fan abnormalities| 1. check whether the fan impeller of the car is jammed.
2. check whether the fan plug is loose and falsely connected.
3. fan failure, replacement of the fan.
4. check whether the wind wheel Induction magnet Is missing or has the wrong polarity.
5. check whether the main board wind speed sensor is normal.
6. main board failure, replace the main board.
0.00E+00| Ignition plug abnormalities| 1. check the ignition plug for false connections.
2. faulty ignition plugs, replace the ignition plugs.
3. main board failure, replace the main board.
0.00E+00| High-temperature protection
sensor.| 1. incorrect or faulty furnace temperature sensor type, replace the
2. main board failure, replace the main board.
0.00E+00| Furnace temperature sensor abnormal| 1. check the furnace temperature sensor connector for loose false connection.
2. incorrect or faulty type of furnace temperature sensor, replace the sensor.
3. main board failure, replace the main board.

FAQ

For any questions you may have about the Hcalory product, please kindly copy this link hcalory.com or scan the below code to contact us. we will help you solve it as soon as possible. If you are satisfied with our items, please leave 5-star feedback on the website to help others to know the items more. Appreciate your kind feedback and support.
About US
Hcalory Official Store is the only official store authorized directly from Hcalory without any transfer link. It is committed to selling 100% original authentic products We have official store sales on all major platforms: All Express: https://frafiexpress.com/store/1875556 eBay: hdps://www.ebay.com.au/usr/hcalory https://vAnv.ebay.de/usobcalory
Email: hcalory hcalory.com
FCC Warning
15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to the user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This e equipment generates uses and can radiate radio Ire quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by timing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for a controlled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

References

• Hcalory Auto Parts Store - Professional Heater And Cooler
• hcalory | eBay Shops
• ebay.eom.au/usr/hcalory

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>