Hcalory TD Series Car Refrigerator User Manual

Car Refrigerator
Use Manual

TD Series Car Refrigerator

NOTE: Please read this manual carefully before use to understand the function and operation requirements of the product.

Car Refrigerator

• Thanks to buy our company car refrigerator, here to express our heartfelt thanks.
• Please read this manual carefully before using it.
• After review, please keep this manual and warranty card properly.

Safety instructions and precautions for use

• Do not kink or damage the power cord.
• Do not pull the refrigerator with the power cord on the car refrigerator.
• Do not pull the power cord at the sharp edges or corners.
• Do not contact the exposed non-insulated power cables.
• This product has a compressor component. Please leave the product flat for 4 hours after receiving it.
• Do not place the product upside down, or tilt above 45 degrees, to avoid product failure.
• Do not hinder the vent; if the refrigerator is placed in the car, the cooling window hole shall reserve more than 10cm space. When the cooling window is blocked, the cooling system will stop due to poor cooling performance and severe high temperature protection.
• It is not recommended to place or store items on the refrigerator; do not bear the weight pressure in the display / operation panel area; the door body area shall not exceed 100kg.
• Do not use hard or sharp tools to remove the ice; do not use abrasive or solvent materials.
• Don’t expose the car refrigerator to the rain.
• Before use, please clean the refrigerator inside and outside of the car with wet cloth; do not install corrosive liquid; please often clean the refrigerator cavity, to prevent odor and bacteria, and ensure food safety. Not used for a long time, please disconnect the power supply, and keep the refrigerator inside and outside clean and dry.
• This product is not intended to be used by persons with abnormal physical, sensory, or mental abilities, defects or poor experience and knowledge (including children), unless they have someone given supervision or guidance to use the equipment who is responsible for their safety.
• Children should be supewised to ensure that they do not use the car refrigerator as toys.

TD30 vehicle refrigerator parameters:

TD40 vehicle refrigerator parameters:

TD50 vehicle refrigerator parameters:

Part introduction:

1. Door handle
2. Door
3. Seal strip
4. Lighting
5. Refrigeration area
6. Frozen area
7. Display screen
8. Control panel| 9. Handle
10. Box body
11. Heat dissipation air duct
12. USB charging port
13. Fuse
14. DC power interface
15. AC power adapter (optional)
16. Car DC power cable
---|---

A. How to connect the 12 / 24V DC power supply:

1. Put the car refrigerator in the car (trunk, seat..) in the flat position of the car, and put it smoothly;
2. Arrange the DC power cable according to the interior space (if you need to cable from the center console to the trunk, the power cable can be buried under the carpet), one end of the power cable is inserted in the power interface of the car refrigerator, and the other end is inserted in the cigarette lighter:
3. Open the door handle, open the top cover, put the required frozen items into the freezing area of the refrigerator, cover the top cover, and ensure that the buckle hand is locked in place.
4. After the power supply is turned on, display the temperature of the box body and start working. The user can adjust the required temperature by himself. Long press the power switch button for 3 seconds, the car refrigerator can be shut down. To start again, long and press the power switch button for 3 seconds again.

| |
---|---|---
Connect car cigarette lighter| Connect power cord connect| Power cord interface

B. How to connect the 100V-240V~ AC power supply:

1. Put the car refrigerator on the smooth ground smoothly;
2. Connect the AC power adapter in the accessory box to the AC power cable; plug the output of the adapter into the vehicle refrigerator DC power interface and connect the plug of the AC cable to the power socket.
3. Open the door handle, open the top cover, put the required frozen items into the freezing area of the refrigerator, cover the top cover, and ensure that the buckle hand is locked in place.
4. After the power supply is turned on, display the temperature of the box body and start working. The user can adjust the required temperature by himself. Long press the power switch button for 3 seconds, the car refrigerator can be shut down. To start again, long and press the power switch button for 3 seconds again. kindly reminder:
   If you need to use 220V household power supply, please buy our special household power adapter for the refrigerator.

How does the control panel operate:

1. Turn on/ off: Long press the power switch button for 3 seconds to turn on or off the car refrigerator.
2. Temperature setting method: in the startup state, short press “+ or key to display the set temperature value and flash, and then short press “+” or “-” to increase or lower the set temperature; the adjustment range is-20°C – – + 20°C. Press the “+” or “-” keys to quickly adjust the temperature setting.
3. On the boot state, short press “SET” key, display “MAX” flash, then short press “+” or “-” to switch between MAX (strong cold) or ECO (energy saving) mode (factory default mode MAX).
4. On the boot state, press the “SET” key for 3 seconds, and the pattern of the battery protection gear is flashing. At this time, press + or – to switch the gear up or down (the factory default is H high, and you can set it to M middle or L low), and then press “SET”. Press “+” or “-” to switch the Fahrenheit/Celsius temperature mode.
5. The boot automatically displays the current temperature in the box.
6. USB output port: can output 5V 2.1A DC power, to charge mobile devices, tablets and other digital devices.
   Tips: The on-board refrigerator has the memory function of power off. The cooling temperature and working mode set before power off will automatically restored after the next power on, without the need to be reset.

Battery protection function description:

1. Battery protection function: The car refrigerator has the three-gear car battery protection function, which can automatically monitor the car battery voltage. Before the power consumption affects the normal ignition of the car, the car refrigerator will automatically stop working, to ensure that the car battery power will not be consumed too low and affect the normal ignition of the car.
2. In the boot state, long press “SET” key for 3 seconds to display the pattern of the current corresponding battery protection gear flashing. At this time, short press “+ or “-” to make the gear switch up or down (the default is M middle gear, which can be set to H high gear or L low gear), so that the refrigerator can work for a longer time. (Lower the battery protection gear by “L” gear when displaying “E1” using an external spare battery or refrigerator screen)
3. The battery protection gear voltage parameter value is shown in the following table:

| 12(V)| 24(V)
---|---|---
Stop voltage| Starting voltage| Stop voltage| Starting voltage
H High Gear| 11.1| 12.4| 24.3| 25.7
M Middle Gear| 10.4| 11.7| 22.8| 24.2
L low Gear| 9.6| 10.9| 21.3| 22.7

Simple fault analysis and handling:

1. The car refrigerator does not work:
   Check that the power supply is properly connected (the plug is loose and the positive and negative electrodes are connected).
   Check that the power switch on the operation panel is activated.
   Check whether the fuse is fused, and check whether the heat dissipation and ventila-tion is normal.
   Start on 30 seconds compressor delay start protection.

2. Poor refrigeration:
   Check whether the refrigerator door is closed, whether the door cover seal strip is damaged or deformed, resulting in lax sealing;
   The refrigerator cooling area has poor ventilation;
   Too much hot food;
   High-intensity sunlight exposure or near the heat source;
   Improper temperature setting;

3. Abnormal noise:
   Unplacement; encounter walls or other items; internal parts are loose or fall off; the sound of running water, which is the flow sound of refrigerant flow, is a normal phenomenon.
   The compressor starts the moment the sound is loud, the motor accelerates from static to high speed operation, the sound will be slightly larger, the sound after the speed is stable
   Sound is reduced, it is a normal phenomenon.

4. The Surface of the refrigerator is exposed
   When the ambient air temperature is> 75%, the surface of the box will produce a slight condensation, that is, the water vapor in the air is liquefied when it meets the refrigerator shell with low temperature, and condenses into small water droplets, which is a normal phenomenon, and can be dried with a towel (raising the cooling temperature is conducive to reducing the phenomenon of condensation).

5. The meaning and handling method of the error code displayed on the screen:

battery protection gear.
E2| Fan over-current protection| Shutdown and stand for 10 minutes before restart; if again, please contact after-sales personnel.
E3| Compressor fault protection (motor plugging or excessive pressure of refrigeration system)| Shutdown and stand for 10 minutes before restart; if again, please contact after-sales personnel.
E4| Compressor fault protection| Shutdown and stand for 10 minutes before restart; if again, please contact after-sales personnel.
E5| Compressor control module for excessive temperature protection| Place the refrigerator in the ventilation place, shutdown and stand for 10 minutes before restart; if they appear again, please contact the after-sales personnel.
E6| NTC fault (short circuit, open circuit)| Please contact the after-sales personnel.

If the abnormal sityation cannot be solved through simple fault analysis, please contact our customer service hotline for processing.

Recommended storage temperature:

| Purified water| 5°C
---|---|---
| Drink| 5°C
| Fresh juice| 8-10°C
| Red wine| 13°C
| Fruit| 5-8°C
| Vegetables| 3-10°C
| Prepared food| 4°C
| Meat| -18°C
| Seafood| -3°C
| Fast cold food| -18°C

Daily maintenance and attention:

Cleaning method:
Every other week, clean and maintain the refrigerator once, wipe the inside and outside surface of the refrigerator with a wet rag. If it is too dirty, you can use neutral detergent and then wipe the washed rag, twist dry and wipe the water stains.
Maintenance of plastic parts:
Properly protect the door seal, must be often kept clean, use when try to avoid oil stains dirty and deformation, if oil (animals Oil or vegetable oil) for a long time attached to the box of plastic parts, plastic is easy to aging or crack, and smell so to
Develop the habit of being clean regularly.
matters need attention:
It is strictly prohibited to wash the water tank directly with water to prevent less electrical insulation and metal parts from rust. The following items (alkaline detergent, soap, grinding powder, hot water, brush, day that water, gasoline, alcohol) will damage the coating layer, plastic parts, and can not be used for cleaning.

Maintenance service:

If there is any fault, please check again before requesting the repair. If the fault can stil not be eliminated, please go to the designated repair point for repair, or contact our company, and please confirm the following matters.
Name, address, telephone number:
Trade name, Model number:
Purchase date (subject to the purchase invoice)
Composition and contents of toxic and harmful substances:
In order to meet the requirements of the Administrative Measures on the Restricted Use of Hazardous Substances in Electrical and Electronic Products, the following provides the names of electrical product components and the information of harmful substances that may be contained.

PBDI ether (PBDE)
Gate component| | | | | |
Box component| | | | | |
Compressor components| | | | | |
Circuit board| | | | | |
Power line| | | | | |
Package parts| | | | | |

The “ ” indicates that the content of the harmful substance in all homogeneous materials of the component is below the limit requirements specified in GB /T 26572-2011. “ ” indicates that the content of the harmful substance at least in all homogeneous  materials of the component exceeds the limit requirements specified in GB / T 26572-2011 due to prior technology and process limitations. Environmental protection service period of electronic information products:
Note: All electrical and electronic products sold in China must be marked with environmental protection service period. The environmental protection service term of the nuclear mark refers to the service term under normal use conditions, temperature, temperature, and not including batteries and other consumables.

Waste disposal:

Correct disposal of waste machines:

| This sign indicates that the product should not be treated simultaneously with other household waste. To avoid possible damage to the environment or human health, responsible recycling is required to promote the maximum reuse of materials. To return waste appliances you used, use the Return and Recycling system or contact the seller of this product. They can recycle this product for reuse.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>