ADAR1DMLTB Seaview Modular Top Plate Instruction Manual
- June 14, 2024
- SEAVIEW
Table of Contents
ADAR1DMLTB Seaview Modular Top Plate
PARTS INCLUDED
-
X1 (ADAGMT)
-
X1 (ADAR1DMLTBP)
-
X12 (51618114FHCS)
TOOLS NEEDED
Sudbury Elastomeric Marine Sealant is recommended. To purchase call 800-655-7922 or visit www.seaviewglobal.com
CLOSED DOMES & STARLINK
| Hole # | Manufacturer | Model |
|---|---|---|
| 11 | B&G | 3G, 4G, HALO20(+), HALO24 |
| 12 | Furuno | 15” – 24” radar domes & SC30 |
| 11 | Garmin | 18” – 24” and Fandom radar domes |
| 8 | Genova | 24” radar domes |
| 2 | Italian | C700 (spacers required) |
| 4 | JRC | 15” radar domes |
| 4 | Kaden | 18” (MDC 900 Series) radar domes RB714A |
15” (MDC 900 Series) radar domes TB715A
10| Kaden| 25” radar domes, 715A, MDC 900 Series
8| Lorenz| 12” – 24” radar domes
5| Lowrance| LR1800HD
11| Lowrance| 3G, 4G, HALO20(+), HALO24
10| Nobel Tec| 15” – 25” radar domes
3| Ray marine| 18” – 24” radar domes
11| Ray marine| Quantum and Quantum 2 radar domes
8| Seia/Tec marine| 12” – 24” radar domes
5| Semrad| 18” radar domes (DX64S)
11| Semrad| 3G, 4G, HALO20(+), HALO24
5| Sitex| 18” (TZ760 / T921) radar domes
10| Sitex| 25” radar domes
3| Star link| Flat High Performance
OPEN ARRAY RADARS
| Hole # | Manufacturer | Model |
|---|---|---|
| 2 | Furuno | 4’ – 6’ open array radars |
| 2 | Garmin | 4’ – 6’ open array radars |
| 7 | Geonav | 4’ – 6’ open array radars |
| 9 | JRC | 4’ – 6’ open array radars |
| 1 | Koden | 4’ – 6’ open array radars |
| 9 | Lorenz | 4’ – 6’ open array radars |
| 9 | Lowrance | 4’ – 6’ open array radars |
| 1 | Nobeltec | 3.5’ – 6’ open array radars |
| 7 | Northstar | 4’ – 6’ open array radars |
| 6 | Raymarine | 4’ – 6’ open array radars May need smaller OD washer |
| 7 | Seiwa / Techmarine | 4’ – 6’ open array radars |
| 7 | Simrad | 4’ – 6’ (RB7 Series) open array radars |
| 3 | Simrad | 4’ – 6’ HALO open array radars Requires #ADAHALO3 adapter plate. |
Drill #3 for adapter plate
7| Sitex| 4’ – 6’ open array radars
-
Locate the Make and Model of your satellite dome on this chart and determine which drill hole number yours is. Then place the ADA-R1 Drill Template on top of the ADAR1DMLTB and mark the appropriate holes.
-
Drill the four marked holes. Be sure to check with your marine electronic manufacturers manual to determine what size drill bit is needed.
-
Apply marine adhesive sealant along the lip in the center hole on the ADAR1DMLTB. Route the cabling through the center hole in the ADAR1DMLTB. Then insert through the black rubber grommet.
TIP
Place the connector of the cable into a plastic bag. Apply Vaseline to the exterior of the plastic bag. Then try routing the connector/cable through the black rubber grommet. -
Be sure that the Top Plate edge sits in the rubber grommet.
-
Make sure that the Top Plate is facing the forward when mounting
NOTE:
If you are using the optional light bar make sure to use four 1 1/4” bolts (516181FHCS).
OPTIONAL ACCESSORIES
Call 800-655-7922 or visit www.seaviewglobal.com for available accessories.
LIGHT BARS
-
LTBR
Fits closed dome radars. -
LTBS
Fits 20” or smaller sat domes.
LIGHT BAR TOPS
-
LTBP1197 Perko 1197 Incandescent Light
-
LTBP1697 Perko LED Light.
-
LTBU1A1197 Light Bar Top with Perko 1197 Light, can fit GPS.
-
LTBU1A1697 Light Bar Top with Perko LED light, can fit GPS.
SPREADER KIT
SP1MOD
Allows user to mount GPS units or antennas onto a Seaview Modular Mount.
NOT to scale
Customer support
Refer to website for most up to date instructions and videos.
WWW.SEAVIEWGLOBAL.COM
Tel: 800-655-7922
www.seaviewglobal.com
EUROPEAN OFFICE
Tel: +33 4 94 53 27 70
www.seaviewprogress.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>