SEAVIEW GLOBAL LTBP-1197 Elevate your electronics Installation Guide

June 5, 2024
SEAVIEW GLOBAL

INSTALLATION
INSTRUCTIONS
For Seaview Lights:
LTBP-1197
Refer to website for most up to

date instructions and videos.
WWW.SEAVIEWGLOBAL.COM

PARTS INCLUDED

TOOLS NEEDED

Sudbury Elastomeric Marine Sealant is recommended. To purchase call 800-655-7922 or visit www.seaviewglobal.com 
NOTE: Please call Perko directly with any wiring questions at 305-621-7525.

  1. Apply marine adhesive sealant around the shaft of the LTBP-1197 and then slide into the top end of the lightbar.

  2. Be sure that the light is facing the correct direction. One way to tell is that the mark on the light base should line up with the push pin hole on the light bar.

  3. Insert the two push pins into the light bar and light to secure.
    NOTE: Please call Perko directly with any wiring questions at 305-621-7525.

OPTIONAL ACCESSORIES

Call 800-655-7922 or visit www.seaviewglobal.com for available accessories.

LIGHT BARS LTB-R
Fits closed dome radars. LTB-S
It Fits 20” or smaller salt domes.

SPREADER KIT

SP1-MOD
Allows user to mount GPS units or antennas onto a Seaview Modular Mount.
WEDGES

Compensates for plane angle. Available in 2, 4 or 6-degree wedges.

Hinge back your Seaview Modular Mount with a Seaview Hinge for added height clearance.
NOTE: Please call Perko directly with any wiring questions at 305-621-7525.
Fig Nos. 1183 Series Combination Masthead and All-Round White (Anchor) Lights. Fig. Nos. 1196 Series Combination Masthead and All-Round White (Anchor) Lights. Fig. Nos. 1197 Series Combination Masthead and All-Round White (Anchor) Lights. The above lights are designed for use on sail or power-driven vessels under 20 meters (65. 6 ft) in length, operating at a nominal 12 volt or 24-volt system. In order to comply with 72 COLREGS and U.S. Inland Navigation Rules*, the following must be adhered to:

MOUNTING INFORMATION Read all instructions before proceeding.

  1. These instructions show the orientation of each light. For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard A-16, the 72 COLREGS and the U.S. Inland Navigation Rules . These lights are supplied complete with 12-volt bulbs (Cat No. 0071 DPOCLR, 12V, 10W), however, 24-volt bulbs (Cat No. 0072001CLR, 24V, 10W) are available for 24-volt systems.

  2. These lights are designed to be mounted on a horizontal surface. 3). Cat. Nos. 1183000CH R, 1183DPOCHR, 1196001CH R, 1196DP1CHR, 1196002CHR, and 1196DP2CHR: These lights are furnished for mounting such that the long dimension of the mounting base is parallel to the fore-aft centerline of the boat. If a mounting is desired such that the long dimension of the mounting base is perpendicular to the fore-aft centerline of the boat, substitute instruction d) below for instructions a) to c). a). Draw a 4-inch long reference line through the center of the selected mounting location and parallel to the fore-aft centerline of the boat.
    b). Cut out the mounting template below. Tape it on the mounting surface such that the reference line (drawn above) is directly underneath the reference line marked on the template.
    c). Drill 2 holes through the template to accommodate #8 round head mounting screws. Drill one 3/8 inch hole to accommodate the electric wiring. (Proceed with instruction #5 below).
    d). Special Instruction only for mounting with the long dimension of the mounting base perpendicular to the fore-aft centerline of the boat:

  3.  Draw a 4-inch long reference line through the center of the selected mounting location and perpendicular to the fore-aft centerline of the boat.

  4. Remove the holding screw (see illustration) and rotate the light assembly on the tube 90° in one direction the other until a second hole appears on the tube. Re-insert the holding screw into the Light assembly such that it enters the new tube hole to anchor the assembly 90° from its original position.

  5. Cut out the mounting template below. Tape it on the mounting surface such that the reference line (drawn above) is directly underneath the reference line marked on the template.

  6. Drill 2 holes through the template to accommodate #8 round head mounting screws. Drill one 3/8 inch hole to accommodate the electrical wiring. 4. Cat. No. 1197000CHR: This light is furnished with a 3/4 inch tube and is designed to be mounted vertically into a 3/4 inch hole.

  7. Attach supply connections to the light making sure to wire in accordance with both A.B.Y.C. Standard E4″ and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183)”. The supply leads are coded as follows:
    WIRING DIAGRAM FOR COMBINATION MASTHEAD/ANCHOR LIGHTS

NOTE: Please call Perko directly with any wiring questions at 305-621-7525.
WHITE: Forward compartment (masthead light) positive lead supply. GRAY or RED: Aft compartment (when energized with the forward compartment: all-around light)positive lead supply. BLACK: Negative lead supply.
(CAUTION: Negative lead connected to the case. To avoid the energizing case, observe polarity). Electrical connections are to be made such that only the forward compartment (masthead light) is energized with the other running lights (sidelights, stern lights, etc.) while underway. Both compartments are energized simultaneously by themselves to create the all-around (anchor) light. Be sure to use double-pole switches, other-wise feedback will cause all lights in the system to be energized at the wrong time. SEE WIRING DIAGRAM.
6). Mount the base in accordance with both the template and instruction #7 below.
7). Make the top of the light is vertical during operation (see illustration) and the arrow on the top cover points ahead (not astern), with the reference mark parallel to the fore-aft centerline of the boat.
8). Relamp only with PERKO Cat. No. 0071 DPOCLR bulbs (12V, 10W) or PERKO Cat. No. 0072DP1 CLR bulbs (24V, 10W) to remain in compliance. The above-referenced standards can be obtained from:
(1). American Boat & Yacht Council,lnc. 3069 Solomans Island Road Edgewater, Maryland 21037
(2). U.S. Coast Guard Washington D.C. 20593 (or your local C.G. office)
MOUNTING TEMPLATE

  • Double-pole, double-throw switch (center off)
  • One position illuminates running lights (masthead, side & stern)
  • Another position illuminates anchor light (forward & aft compartments of combination masthead/anchor light)

NOTE: TOP OF LIGHT MUST BE VERTICAL DURING OPERATION PERKO, INC. 16490 N.W. 13th Avenue Miami, FL 33169-5707 www.perko.com
2/04 11831NS1
NOTE: Please call Perko directly with any wiring questions at 305-621-7525.

EUROPEAN OFFICE
Tel:800-655-7922
www.seaviewglobal.com
Tel: +33 4 94 53 27 70
www.seaviewprogress.com
5-03162021

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals