NOMA 50854 Smart Door and Window Sensor User Manual

NOMA 50854 Smart Door and Window Sensor

WHAT’S IN THE BOX

PRODUCT INFORMATION

1. SMART DOOR AND WINDOW SENSOR

2. MOUNTING ACCESSORY

3. CR123A BATTERY

PRODUCT INFORMATION

NOTE:
Tamperproof: When the magnetic shell is removed, the app will receive a notification and report the status (Open/Closed).

SMART DOOR AND WINDOW SENSOR

PAIRING/MOUNTING INSTRUCTIONS

PAIRING INSTRUCTIONS

• Remove the “pull tab” on the back of the main sensor. The battery will be connected, and the sensor will automatically be in pairing mode and LED light will start flashing rapidly.
• If not in pairing mode (LED light not flashing), open the main casing (refer to battery replacement section), press and hold the power/reset button for 5 seconds until LED light is flashing rapidly.
• In order to pair the device, please enable and give permission for Location Services and Bluetooth® on your mobile device.
• In the NOMA iQ™ app, select the·+· symbol in the top right-hand corner. Select the device and follow the instructions within the app.
• If the device is not paired within 3 min, it will exit pairing mode, Please refer back to the second step to restart the pairing process.

MOUNTING INSTRUCTIONS

Note: The sensor must be installed indoors,

• When you select your mounting location, make sure the surface area is clean.
• During the mounting process, ensure that both the main sensor and secondary sensors are aligned correctly. Use the alignment lines indicated on the main and secondary sensors. In order for the sensors to work optimally, they must be placed as close together as possible. The limits prescribed in the alignment instructions section are for reference. Before final assembly, please ensure you’re receiving notifications with the sensors roughly in place while opening and closing the window/door.
• Place the included adhesive tape on the back of the main and secondary sensors. Select your location and mount the main and secondary sensors.
• Once mounted, please ensure the sensor is working as intended. When the window/door is opened or closed, the LED on the sensor will momentarily light up and you should receive a notification on your mobile phone (please ensure to turn on notifications in the NOMA iQ™ app in the device settings).

SMART DOOR AND WINDOW SENSOR

PAIRING/MOUNTING INSTRUCTIONS

ALIGNMENT INSTRUCTIONS

Step 1: Attach the main device to the door frame (or window frame) with 3m adhesive tape.

Step 2: The magnet shell is attached to the door (or window) with 3M adhesive, and the two marks are aligned.

Complete installation.

Position of X axis 0.

Maximum distance of X axis 10 MM,

Maximum positive distance of Z axis 10 MM.

Maximum negative distance of Z axis 10 MM.

WARNING

WARNING AND CAUTION

WARNING:
Keep batteries away from children and pets.

• Follow the battery manufacturer’s safety and usage instructions.
• Insert the battery observing the proper polarity(+/-) as indicated inside the battery compartment.

CAUTION:
Failure to properly align the battery polarity can cause personal injury and/or property damage.

• Remove a spent or discharged battery from the product.
• Never throw batteries into a fire. Do not expose batteries to fire or other heat sources.

DISPOSAL OF USED BATTERIES

Battery may contain hazardous substances which could endanger the environment and human health. Used batteries shall not be treated as municipal waste, but left at the appropriate collection point for recycling. For more information about collection and recycling of used batteries, please contact your local municipality or waste disposal service.

• Use type CR123A battery.(Smart Door and Window Sensor)
• Install only new batteries of the same type in your product.
• Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause batteries to leak.
• Danger of explosion if battery is incorrectly replaced.
• Batteries should be recycled or disposed of as per state and local guidelines.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel cadmium) or (nickel metal hydride) batteries.

WARNING

SPECIFICATIONS

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
READ ALL INSTRUCTIONS BEFORE USE.

• WARNING – To reduce the risk of fire, electric shock, or serious personal injury:
• Do not ingest or swallow the battery.
• This product is not intended for use by children and contains small parts that may pose a choking hazard to children under the age of three. Keep the product out of the reach of children and pets.

SPECIFICATIONS

• Required battery: CR123A
• Standby current: 13 μA
• Working current: 115 mA-120 mA
• Wireless type: 2.4 GHz
• Wireless range: 30 m
• Wireless Protocol: IEEE 802.llb/g/n

WARNING

BATTERY REPLACEMENT & WARRANTY

BATTERY REPLACEMENT:

1. Push the button while holding the main sensor, and slide the casing in an upward direction.
2. Remove the spent battery and place CR123A battery into the battery compartment.
3. Replace the battery compartment cover.

LIMITED WARRANTY:

This NOMA product carries a one (1) year repair warranty against defects in workmanship and materials. At its discretion, NOMA Canada agrees to have any defective part(s) repaired or replaced free of charge within the stated warranty period when returned with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.

FCC PART 15 WARNINGS

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the use(s authority to operate the equipment.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING INFO

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF WARNING FOR MOBILE DEVICE

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

IC STATEMENT

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt

RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
   This Class B digital apparatus complies with CAN ICES-003 (B)/NMB-003 (B).

This equipment should be installed and operated with minimum distance between 20cm the radiator your body.

CUSTOMERS SUPPORT

FCC Responsible party:
Globe Electric
2264 East 6th Street
San Bernardino, CA 92410
www.globe-electric.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>