SEAVIEW SP1MOD Spreader Kits Instruction Manual

SEAVIEW SP1MOD Spreader Kits

Product Information

Specifications:

• Compatible Spreader Kits : SP1MOD, SP2MOD
• Parts Included : SP1MOD, SP2MOD, SP1 Extension Rod, SP6, SP8, SP10, SP3, SP12, SP7SS
• Tools Needed : Sudbury Elastomeric Marine Sealant

Product Usage Instructions

Installation Instructions:

1. Apply the rubber grommet onto the threaded adapter and then insert it through the spreader.
2. Apply another rubber grommet and plastic nut on the threaded adapter.
3. If you are using a satellite dome, the plastic extension rod is not needed. Apply marine adhesive sealant to the threads of the adapter and screw on the GPS unit. Route the cables through the spreader.
4. If you are using a closed dome radar, use the provided plastic extension rods. Apply marine adhesive sealant to the threads of the adapter and screw on the GPS unit. Route the cables through the spreader.
5. If your fiberglass antenna is less than 4′ tall, then you are okay to proceed.
6. Do NOT use 4′ or taller fiberglass antennas with Seaview Spreader Kits. Please call 800-523-7558 for further assistance.
7. Place the rubber gaskets onto the sides of the center spreader body, ensuring that the six mounting holes line up.
8. Route the cables through the center spreader body.
9. Insert the eight black plastic shoulder washers into the spreader bolt holes. Using the eight 1/4-20 x 1 bolts, tighten the spreaders with an Allen wrench.
10. Place the rubber gasket in the groove on the top of the Seaview mount. Then, place the Spreader Kit on top of the mount assembly.
11. If you are using an optional Seaview Lightbar, wrap the rubber bushing around the end of the lightbar.
12. Place the white plastic adapter piece on top of the rubber bushing. Place the stainless steel bracket onto the bottom rubber bushing.
13. Place the white plastic spacer on top of the adapter.
14. Insert the lightbar into the back of the Seaview mount.

Optional Accessories
Call 800-655-7922 or visit www.seaviewglobal.com for available accessories.

• Spreader Flood Cable Seals Light Kit (SPLTLED): Flood Light Kit for Tapered Mast spreaders.
• Seaview Cable Glands: Provide waterproof cable routing.
• Hinges: Seaview Hinge Adapters fold in any direction necessary for added height clearance.
• Wedges: Compensates for plane angle. Available in 2, 4, or 6-degree wedges.
• Light Bars:
  • LTBR: Fits closed dome radars.
  • LTBS: Fits 20 or smaller sat domes.
• Light Bar Tops:
  • LTBLED12 (White LED nav light)
  • LTBLED12BLK (Black LED nav light)
  • LTBU1ALED12: Light bar top with Seaview LED light on 12 posts and 1-14 threads for GPS.

FAQ

Where can I purchase Sudbury Elastomeric Marine Sealant?
You can purchase Sudbury Elastomeric Marine Sealant by calling 800-655-7922 or visiting www.seaviewglobal.com.

Can I use a fiberglass antenna taller than 4′ with Seaview Spreader Kits?
No, it is not recommended to use a 4′ or taller fiberglass antenna with Seaview Spreader Kits. Please call 800-523-7558 for further assistance.

How do I install a light bar if my top plate is 3/4 or thicker?
Use 4 each of the 5/16 x 3 bolts when installing a light bar if your top plate is 3/4 or thicker.

Where can I find additional accessories for the product?
You can call 800-655-7922 or visit www.seaviewglobal.com for available accessories.

PARTS INCLUDED

TOOLS NEEDED

Sudbury Elastomeric Marine Sealant is recommended. To purchase call 800-655-7922 or visit www.seaviewglobal.com

Installation Instructions

1. Apply the rubber grommet onto the threaded adapter and then insert it through the spreader.
   • Apply another rubber grommet and plastic nut on the threaded adapter.
2. If you are using a satellite dome the plastic extension rod is not needed. Apply marine adhesive sealant to the threads of the adapter and screw on the GPS unit. Route the cables through the spreader.
3. If you are using a closed dome radar use the provided plastic extension rods. Apply marine adhesive sealant to the threads of the adapter and screw on the GPS unit. Route the cables through the spreader.
4. If your fiberglass antenna is less than 4’ tall then you are ok.
5. Do NOT use 4’ or taller fiberglass antennas with Seaview Spreader Kits. Please call 800-523-7558.
6. Place the rubber gaskets onto the sides of the center spreader body. Make sure that the six mounting holes line up.
7. Route the cables through the center spreader body.
8. Insert the eight black plastic shoulder washers into the spreader bolt holes.
   • Using the eight 1⁄4-20 x 1” bolts tighten the spreaders with an Allen wrench.
9. Place the rubber gasket in the groove on the top of the Seaview mount.
   • Then place the Spreader Kit on top of the mount assembly.
10. Place the rubber gasket that comes with the Seaview Top Plate Kit into the groove on the top of the Spreader Kit center body.
    • Bolt the assembly together using the eight 5/16 x 2¾” bolts.
11. If you are using an optional Seaview Lightbar wrap the rubber bushing around the end of the lightbar.
12. Place the white plastic adapter piece on top of the rubber bushing.
    • Place the stainless steel bracket onto the bottom of the rubber bushing.
13. Place the white plastic spacer on top of the adapter.
14. Insert the lightbar into the back of the Seaview mount.
15. Bolt the assembly together with four 5/16 x 2¾” bolts.
    • NOTE: Use 4 each of the 5/16” x 3” bolts when installing a light bar if your top plate is 3/4” or thicker.

OPTIONAL ACCESSORIES
Call 800-655-7922 or visit www.seaviewglobal.com for available accessories.

SPREADER FLOOD LIGHT KIT

SPLTLED
Flood Light Kit for Tapered Mast spreaders.

CABLE SEALS
Seaview Cable Glands provides waterproof cable routing.

HINGES
Seaview Hinge Adapters fold in any direction necessary for added height clearance.

WEDGES
Compensates for plane angle. Available in 2, 4, or 6-degree wedges.

LIGHT BARS

• LTBR
  Fits closed dome radars.

• LTBS
  Fits 20” or smaller sat domes.

LIGHT BAR TOPS

• LTBLED12
  (White LED nav light)

• LTBLED12BLK
  (Black LED nav light)

• LTBU1ALED12
  Light bar top with Seaview LED light on 12” post and 1-14 threads for GPS.

Tel : 800-655-7922 www.seaviewglobal.com

EUROPEAN OFFICE
Tel : +33 4 94 53 27 70 www.seaviewprogress.com

2-04202023

References

• Seaview | Leaders In Mounting Solutions For Marine Electronics
• Profitez des meilleurs équipements pour votre bateau

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>