Havis DS-DELL-601 Docking Station for Dell Latitude Rugged 12 Tablet Owner’s Manual

Before Beginning

Havis is pleased to provide this Owner’s Manual to aid in the proper installation and use of the DS-DELL-600 Series Docking Station for Dell Latitude Rugged 12 Tablet.
For questions regarding the set-up of your DS-DELL-600 Series Docking Station, please contact Havis at 1-800-524-9900 or visit www.havis.com for additional product support and information.

This Owner’s Manual applies to the following Part Numbers:
DS-DELL-601
DS-DELL-601-2
DS-DELL-602
DS-DELL-602-2
DS-DELL-603
DS-DELL-603-2
DS-DELL-607
DS-DELL-607-2
DS-DELL-608
DS-DELL-608-2

WARNING

• NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE.
• DO NOT USE COMPUTER WHILE DRIVING.

CAUTION

• READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.
• DO NOT STORE, INSTALL, OR OPERATE THE DOCKING STATION WHERE WATER, MOISTURE, STEAM, DUST, ETC. ARE PRESENT
• FOR THE DS-DELL-601, DS-DELL-601-2, DS-DELL-602, DS-DELL-602-2, DS-DELL-607, DS-DELL-607-2, DS-DELL-608, DS-DELL-608-2 DOCKING STATIONS: DO NOT CONNECT DIRECTLY
  TO VEHICLE VOLTAGE SOURCE: This product requires a certified, automotive grade, Dell approved 90W power source rated for a continuous, regulated 19.5VDC output (Havis Part Number LPS-138 or equivalent). Failure to comply with this requirement will cause product damage that is NOT covered under warranty.

NOTICE

• FOR DOCKING STATION MODELS EQUIPPED WITH A BUNDLED POWER SUPPLY (DS-DELL-602, DSDELL-602-2, DS-DELL-608, DS-DELL-608-2) REFER TO THE SUPPLIED LIND POWER SUPPLY REFERENCE GUIDE.

Precautions

• Do not place metal objects or containers of liquid on top of the Docking Station
• If a malfunction occurs, immediately unplug the Power Supply and remove the tablet
• Use only the specified Power Supply (Part # LPS-138 or equivalent) with this Docking Station.
• Do not connect cables into ports other than what they are specified for
• Do not leave the Docking Station in a high temperature environment (greater than 85°C, 185°F) for a long period of time

Specifications

Power Supply Input| DS-DELL-601, 601-2DS-DELL-602, 602-2DS-DELL-607, 607 -2DS-DELL-608, 608-2| External Power Supply (LPS-138 DC-DC)| 19.5V DC-In
---|---|---|---
Dimensions| 11.5” ( 29.2 cm) H x 11.3” ( 28.7 cm ) W x 4.0” ( 10.2 cm ) D
Weight| 4.88 lbs ( 2.21 kg )
Operating Environment| -29° C to 63° C ( -20° F to 145°F )
Storage Environment| -40° C to 85° C ( -40° F to 185° F )

Parts Included

Hardware Kit (HWK-0036)

This Hardware Kit includes:

1. Zip Ties (5)

2. Keys (2)

3. 1/4”-20 x 5/8” long Button Head Screws (5)

4. 1/4”-20 x 3/8” long Pan Head Screws (5)

Tools required for installation:

• 3 Phillips

  (For attaching Mounting Bracket to Docking Station with Pan Head 1/4”-20 Screws)

• 5/32” Hex Drive
  (For attaching Mounting Bracket to Motion Device with Button Head 1/4”-20 Screws)

Docking Station

Port Replication Capability

Forward Facing Ports

(All Docking Stations, not including DS-DELL-603 & DS-DELL-603-2)

Rear Ports – Advanced Electronics

(DS-DELL-601, DS-DELL-601-2, DS-DELL-602, DS-DELL-602-2)

Rear Ports – Standard Electronics

(DS-DELL-607, DS-DELL-607-2, DS-DELL-608, DS-DELL-608-2)

Antenna Identification

(DS-DELL-601-2, 602-2, 603-2, 607-2, 608-2)

Downward Facing Antennas

**Tablet Interface

**

Installation and Cable Management

NOTE: We recommend applying a drop of medium strength (blue) thread locking adhesive to the threads of all fasteners.

1. Remove the Mounting Bracket from the packaging. Install the Mounting Bracket to the Motion Device using (4) 1/4“-20 x 5/8” long button head screws (Hardware Kit Item 3).
   Torque screws to 80 in-lbs (9.0Nm) ± 10%.
   NOTE: Numerous hole patterns present in Mounting Bracket will accommodate Havis Motion Devices as well as most competitors’
   

2. Install all cables that are necessary for computing needs. Use Zip Ties (Hardware Kit Item 1) to strain relieve cables to the Strain Relief Points, routing all cables together to the front of the Docking Station.
   

3. Place the Docking Station onto the Mounting Bracket by guiding the mounting bracket locators into the mounting guides.
   

4. Secure with (4) 1/4”-20 x 3/8” long pan head screws (Hardware Kit Item 4). Torque screws to 80 in-lbs (9.0 Nm) ± 10%.

5. Create a service loop with cable bundle to ensure that no tension is on the connectors and to enable intended motion.

6. Tie off cables onto a stationary part of the mounting system. (Mounting system not included with Docking Station)
   

Operation

Docking

CAUTION

DO NOT FORCE TABLET ONTO DOCKING STATION. IF THERE IS RESISTANCE, CHECK THE ALIGNMENT OF TABLET ON DOCKING STATION.

Your tablet’s Alignment Sockets will align with the Docking Station’s Alignment Posts.

1. Ensure Docking Station is unlatched by pulling the Latch Handle forward.

2. Hold tablet in landscape orientation, with bottom angled toward Docking Station. Lower tablet into the bottom of the Docking Station by aligning the tablet Alignment Sockets with the Docking Station’s Alignment Posts.

WARNING
DO NOT DOCK TABLET BACKWARDS IN THE DOCKING STATION OR DAMAGE TO THE SCREEN, TABLET ELECTRONICS, AND DOCKING STATION ELECTRONICS WILL RESULT

3. Pivot the top of tablet into Docking Station and apply light rearward pressure to top center of tablet. An audible click will indicate when tablet is latched.

4. For theft deterrence, secure tablet by locking Docking Station with supplied key (Hardware Kit item 2).
   

Undocking

1. If previously locked, unlock Docking Station using supplied key.
   

2. While holding tablet with one hand, pull the Latch Handle on the top of Docking Station until the Latch Hooks release.

3. Once unlatched grab both sides of tablet, rock the top forward and carefully lift out of Docking Station, top end first.
   

Related Products

Havis offers a wide variety of accessory products specifically for use with the DS-DELL-600 Series Docking Station. For more information or to order, please visit www.havis.com.

LPS-138
90W Power Supply
External power supply with cigarette lighter adaptor and Dell miniBondi output cable for Havis Docking Stations.

LPS-211
Multipurpose Bracket Secures Power Supplies On Havis Docking Stations Or Cradles
Mount a power supply or USB hub directly to your docking station or cradle with this versatile bracket

DS-DA-218
Desktop Stand
Durable stand for mounting the DS-DELL-600 Series Docking Station in the home or office.

LPS-132
20-60V Isolated Power Supply For Use With DS-DELL-600 & 610 Series Docking Stations
90 w LIND power supply with attached input cable, 41-inch output power cable with plug in connector, and Mounting hardware.

LPS-133
12-32V Isolated Power Supply For Use With DS-DELL-600 & 610 Series Docking Stations
90 w LIND power supply with attached input cable, 41-inch output power cable with plug in connector, and Mounting hardware.

DS-DA-501
Replacement Keys
Set of two (2) replacement keys for DS-DELL-600 Series Docking Stations.

Havis, Inc.
75 Jacksonville Road
Warminster, PA 18974
www.havis.com 1-800-524-9900

References

• Rugged Vehicle Mounts, Consoles, Docking Solutions | Havis Inc. NRL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>