HAVIS C-DMM-3119 Vehicle Mount for All-terrain Vehi Instruction Manual

June 13, 2024
HAVIS

HAVIS-LOGO

HAVIS C-DMM-3119 Vehicle Mount for All-terrain Vehi

Product Information

The C-DMM-3119 Flip up Dash Monitor Mount is designed for the 2021-2023 Chevrolet Tahoe PPV and 2021-2023 Chevrolet Fleet Suburban (1FL trim level only). It is a dash monitor mount that allows you to securely attach a display or docking station to your vehicle’s dashboard.

The product comes with the following hardware and parts for installation:

  • 2 Upper dash mounting brackets
  • 2 Lower dash mounting brackets
  • 1 DS DMM frame mounting bracket
  • 1 PS DMM frame mounting bracket
  • 8 10-32 x 3/8 Machine screws
  • 8 10-32 Keps nuts

The swivel plate on the mount has a VESA 75 hole pattern for easy mounting of compatible devices.

Product Usage Instructions

  1. Before installing the C-DMM-3119, read all instructions provided by Havis, Inc. carefully.
  2. Make sure to use the hardware provided with the installation kit.
  3. To begin installation, gently pry and remove the upper dash trim on the passenger side using a panel removal tool.
  4. Unclip and remove the trim above the shifter buttons.
  5. Remove the side cover next to the glovebox by removing the 7mm head fastener.
  6. Remove all 7mm head fasteners from the top of the trim and remove the trim from the vehicle.
  7. Locate and remove the 7mm head fastener found behind the previously removed trim.
  8. Attach the lower dash mounting bracket as shown using the previously removed fasteners.
  9. Reattach the previously removed dash trim.
  10. Attach the upper dash mounting bracket on the driver side and passenger side using the previously removed fasteners.
  11. Snap back in the upper driver side dash trim, allowing the mounting bracket to stick out the top.
  12. Snap back in the upper passenger side dash trim, allowing the mounting bracket to stick out the top.
  13. Attach the DMM frame to the frame mounting brackets using the provided 10-32 x 3/8 screws and keps nuts.
  14. Place the DMM frame on the upper dash mounting brackets and attach using the provided screws and keps nuts.
  15. Attach the DMM frame to the lower dash mounting brackets using the provided screws and keps nuts.
  16. Attach your display or docking station to the VESA 75 holes in the swivel bracket. It is easiest to do this by opening the door and tilting the bracket.
  17. Route the wiring as needed.
  18. Your installation is now complete.

INSTALLATION INSTRUCTIONS

C-DMM-3119 Flip up Dash Monitor Mount
2021-2023 Chevrolet Tahoe PPV
2021-2023 Chevrolet Fleet Suburban (1FL trim level only)

TOOLS REQUIRED:

  • Ratchet Wrench
  • 7/16” Open End Wrench
  • File (for plastic)
  • Phillips Screwdriver (short)
  • Dash panel removal tool
  • Wire stripers/cutters
  • Socket Set

HARDWARE and PARTS shipped loose for installation:

QTY DESCRIPTION PART#
2 Upper dash mounting bracket 23564
2 Lower dash mounting bracket 23563
1 DS DMM frame mounting bracket 24047
1 PS DMM frame mounting bracket 24048
8 10-32 x 3/8” Machine screw 16398
8 10-32 Keps nut 16017

Notes:

  1. Swivel plate for mounting to a device has VESA 75 hole pattern

Always!

  • Read all instructions before installing any Havis, Inc. products.
  • Use hardware provided with install kit

Assembly

HAVIS-C-DMM-3119-Vehicle-Mount-for-All-terrain-
Vehicle-1

Remove upper dash trim on passenger side by gently prying with a panel removal tool.

Unclip and remove trim above shifter buttons.

Remove side cover next to glovebox.
Remove 7mm head fastener.

Remove all 7mm head fasteners from top of trim. Remove trim from vehicle.

Remove 7mm head fastener found behind previously removed trim.

Reattach previously removed dash trim.

Attach upper dash mounting bracket as shown on driver side using previously removed fastener.

Attach upper dash mounting bracket as shown on passenger side using previously removed fastener.

Snap back in upper driver side dash trim allowing mounting bracket to stick out the top.

Snap upper passenger side dash trim back in allowing mounting bracket to stick out the top.

Attach the DMM frame to frame mounting brackets using 10-32 x 3/8” screws and keps nuts.

Place DMM frame on upper dash mounting brackets and attach using 10-32 x 3/8” screws and keps nuts.

Attach to DMM frame to lower dash mounting brackets using 10-32 x 3/8” screws and keps nuts.

Attach display or docking station to VESA 75 holes in swivel bracket. It is easiest to do this by opening door and tilting bracket.

Route wiring as needed.

Installation is now complete.

Havis, Inc.
75 Jacksonville Road
Warminster, PA 18974
T800-524-9900 F 215-957-0729
www.havis.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals