AIBOO RGB Color Changing Christmas Xmas Decoration LED Instructions

AIBOO RGB Color Changing Christmas Xmas Decoration LED

PRODUCT PROFILE & PACKING

PROFILE

4 PUCK lIGHTS KIT

6 PUCK liGHTS KIT

8 PUCK lIGHTS KIT

PACKING LIST

NO| Part name| Specifications| 4 Puck Lights kit| 6 Puck Lights Kit| 8 Puck Lights Kit
---|---|---|---|---|---
A| Adapter| Input:AC100-240V 50/60HZ

L=150cm/59inch 12V 1.5A

|  |  | 1
C| Adapter| Input:AC100-240V 50/60HZ

L=150cm/59inch 12V 1A

| 1| 1|
D| On/Off Switch| L=50cm/19.6inch| 1| 1| 1
E| Controller| L=30cm/11.8inch| 1| 1| 1
H| Extension Cord| L=150cm/59inch|  | 2| 2
I| Puck Light| L=150cm/59inch| 4| 6| 8
F| 8 Way Splitter| White Splitter with 8 Ports|  | 1| 1
J| 4 Way Splitter| White Splitter with 4 Ports| 1|  |
K| Remote| 18 Keys| 1| 1| 1
L| Remote Bracket| White Bracket| 1| 1| 1
M| Two Sided Sticker| Circular, Diameter: 40mm| 8| 12| 16
N| Two Sided Sticker| Rectangle, Dimension:

25X20mm

| 1| 1| 1
P| Screw| ST3.5x10mm, Phillips Self-tapping Screw| 8| 12| 16

Specifications Of Puck Light

Size| L=150cm/59inch                           A=6cm/2.3inch D=0.8cm/0.3inch
---|---
Power| 2W| Voltage| DC12V
Beam Angle| 120 Degrees|  |

INSTALLATION

WARNING: PLEASE READ THE INSTRUCTION CAREFULLY AND TURN ELECTRICITY OFF BEFORE INSTALLATION.

1. TO AVOID EQUIPMENT DAMAGE OR OTHER ACCIDENTS CAUSED BY SHORT CIRCUIT, PLEASE ENSURE THAT THE CONNECTORS ARE FULLY INSERTED WHEN CONNECTING THE WIRES.
2. PLEASE INSTALL THE aDAPTER（a⁄¢）IN A WELL-VENTILATED PLACE WHERE THE AMBIENT TEMPERATURE IS APPROPRIATE.
3. IF YOU FIND SOME ISSUES AFTER INSTALLATION, PLEASE TRY TO FIX THEM ACCORDING TO THE BELOW FAULT aNALYSIS & sOLUTION. iF THE ISSUES STILL WON’T BE SOLVED, PLEASE CONTACT THE SELLER FOR SUPPORT

Step 1: Connection Of Puck Lights Kit

• Before installation, please get to know the connection of light fixture.
• The connection of 4 puck light kit refers to the below picture.
• The connection of 6 puck lights kit refers to the below picture. And the two extension cords (H) can be connected with each of puck lights (I). No need to connect like the picture shows.
• The connection of 8 puck lights kit refers to the below picture. And the two extension cords (H) can be connected with each of puck lights (l). No need to Arrow To Arrow.

Warning: The arrow on the controller (E) should point to the arrow on the splitter (J/F) while connection.

Note All above puck lights kits

1. The adapter can be connected directly with the controller (E) without the component on/off Switch (D).
2. All the ports of the splitter (F/)) don’t need to get all the puck lights (I) connected for your use.

Step 2: Two Installation Ways Of LED Puck Lights

1. Installation Ways I: Mounted With Screws (P)
2. As the picture shows, please open the cover of led puck light (I) according to the direction of the arrows.
3. Get the screws (P) mounted through the installation holes to fix the puck light in the installation position. the arrows.
4. Tighten the cover of the puck light.
5. Installation Ways II: Install with Two Sided Stickers (M)

Use two sided stickers (M) to stick the puck light (I) on the installation position.

Step 3: Fix the Remote (K)

• Use the two sided sticker (N) to get the remote bracket (L) mounted on the installation position, and put the remote (K) into it.
• So far, the installation of puck lights has been completed.
• Remove the plastic sheet of the remote and use the remote to control the lights.
• The instruction of using the remote control refers to other separate manual.

Failure analysis and solution

All lights are not on

| 1.Remove the on/off switch (D), then get the adapter connected with the controller (E) directly. If all the lights can turn on, it is the issue of the on/off switch.| 1. Replace the on/off switch
Individual light is not on| 2.Install the defective puck light with other ports of the splitter to check whether it can work well. If it still doesn’t work, it is the issue of the puck light.| 3. Replace puck light
The remote d oesn’t control the lights.| 3.Not remove the plastic sheet.

4. The battery of the remote is not charged.

5.The remote doesn’t pair with the controller. Or the remote is paired with other controller.

| 4. Remove the plastic sheet
5.Replace the battery of the remote

6.Repair with remote control

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>