AIBOO 6-10-12 Linkable Under Cabinet LED Lighting Puck Light Instruction Manual

AIBOO 6-10-12 Linkable Under Cabinet LED Lighting Puck Light

Product Information

Specifications

• Size: L1=10cm/3.9inch, L2=80cm/31.5inch, A=6cm/2.36inch, D=0.8cm/0.31inch
• Power: 2W
• Voltage: DC12V
• Beam Angle: 120 Degrees

Product Profile & Packing

Profile
The 6/10/12 Puck Lights Kit has the following dimensions:

• A1=120cm/47.2inch
• A2=100cm/39.4inch
• A3=50cm/19.6inch
• A4=30cm/11.8inch
• A5=150/59inch
• A6=80cm/31.5inch
• A7=10cm/3.9inch

Note: The connection ways of all puck lights kits in the above pictures shown are one of the connection methods. There are various ways to connect the light fixture. Refer to Step 1: Connection Of Puck Lights Kit, the detailed connection method is explained below.

Packing List

Specifications Of Puck Light

Installation

Warning:
Please read the instructions carefully and turn off the electricity before installation.

1. To avoid equipment damage or other accidents caused by short circuit, please ensure that the connectors are fully inserted when connecting the wires.
2. Please install the Adapter（B ) in a well-ventilated place where the ambient temperature is appropriate.
3. If you find some issues after installation, please try to fix them according to the below Fault Analysis & Solution. If the issues still won’t be solved, please contact the seller for support.

Step 1: Connection Of Puck Lights Kit
Before installation of the led puck lights (I), please decide to how to connect the light fixture. The connection methods of lighting fixture are flexible and diverse.

Way I: Puck Lights (I) only connect to one port of the splitter (J)
All the puck lights can be connected with 1/2/3/4/5/6 any one port of the splitter (J) which is with 6 same ports. Besides, the extension cords (H) can be used to extend the length of cords of puck lights for your use.
( If you want to add more puck lights to use, please take care of the following problems:

1. The brightness of the puck lights will be dimmer if connect more puck lights in series.
2. The total power of the connected puck lights couldn’t exceed the load of the power supply.
3. As for the first problem, you can connect the power supply with both ends of puck lights to address the issue. Any other problems, please contact seller for the support. )

Way II: Puck Lights (I) connect to two or more ports of the splitter (J)
All the puck lights can be connected with 1/2/3/4/5/6 any two or more ports of the splitter (J) which is with 6 same ports. Besides, the extension cords (H) can be used to extend the length of cords of puck lights for your use.

Note： All above connection ways of puck lights

1. The adapter (A/C) can be connected directly with the splitter (J) without the comp onent controller (E) & on/off switch (D).

All the ports of the splitter (J) don’t need to get all the puck lights (I) connected for your use.

Step 2: Two Installation Ways Of LED Puck Lights
Installation Ways I: Mounted With Screws (P)

1. Open the cover of the LED puck light (I) according to the direction of the arrows.
2. Mount the screws (P) through the installation holes to fix the puck light in the installation position.
3. Tighten the cover of the puck light.

Installation Ways II: Install with
Two Sided Stickers (M)
Use two sided stickers (M) to stick the puck light (I) on the installation position.

Step 3: Get the adapter (A/B) charged

1. As shown in the following figure, tighten the copper core of the corresponding wire and screw it into the wire nut (F) to ensure good circuit continuity.

Step 4: Fix the Remote (K)

Use the two sided sticker (N) to get the remote bracket (L) mounted on the installation position, and put the remote (K) into it. So far, the installation of puck lights has been completed. Remove the plastic sheet of the remote and use the remote to control the lights. The instruction of using the remote control refers to other separate manual.

Fault Analysis & Solution

If you encounter any issues after installation, please try to fix them according to the below Fault Analysis & Solution. If the issues still won’t be solved, please contact the seller for support.

adapter connected with the splitter directly. If all the lights can turn on, it is the issue of the controller.
2.  Remove the controller (E) and the on/off switch (D), then get the adapter connected with the splitter directly. If all the lights still don’t turn on, it is the issue of the power supply.| 1. Replace the controller
2.  Replace the power supply
Individual light is not on| 3.Install the defective puck light with other ports of the splitter to check whether it can work well. If it still doesn’t work, it is the issue of the puck light.| 3.Replace puck light
The remote doesn’t control the lights.| 4. Not remove the plastic sheet.
5. The battery of the remote is not charged.
6. The remote doesn’t pair with the controller. Or the remote is paired with other controller.| 4. Remove the plastic sheet
5. Replace the battery of the remote
6. Repair with remote control

FAQ

Q: How many ports does the splitter (J) have?
A: The splitter (J) has 6 ports.
Q: Can I mount the puck lights without using screws?
A: Yes, you can use the provided two-sided stickers (M and N) to mount the puck lights.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>