TerraTrike Rogue Wheel and Sprocket Instruction Manual

June 12, 2024
TerraTrike

TerraTrike Rogue Wheel and Sprocket Instruction Manual
TerraTrike Rogue Wheel and Sprocket

Alignment

Inflate tires before performing alignment. The Rogue alignment measurement is approximately 30¼” (center tread to center tread), though slight variance is possible. Most importantly, make sure the alignment remains neutral with a rider seated in the trike.
Alignment

Direct Steering Stack Assembly

Assemble the steering stack as shown. Grease the steerer tube before inserting into head tube. Remove any excess grease from steerer tube before installing handlebar. Grease axle before installing wheel. Torque axle to 23-25Nm.

Right Hand assembly depicted. Some components can be purchased individually as well as in pairs, see parts list below.

Parts List

1 M6x18 Bolt TT000415
2 Direct Steer Hubmount Cap TT000161
3 Twist Handlebar – RH TT000655
Twist Handlebar – LH TT000646
Twist Handlebar – Pair TT000271
M6x16 Bolt (not pictured) TT000294
4 M20 Washer TT000254
5 Direct Steer Hubmount – RH TT000828
Direct Steer Hubmount – Pair TT000829
TT000653
6 Bushings (pre-installed) TT000809

Product Instruction
Chain Tube Setup
Mount the chain tube assemblies as shown below. Ensure the chain tubes  do not rotate in the clamps after tightening the pinch bolts.
Upper:
Mounting
Lower:

Mounting

Parts List

Upper Assy.| Chain Tube, 102cm LDPE| TT000540|
---|---|---|---
| Chain Tube Clamp, Rov/Rann/Mav| TT000152|
| M5x18 Pan Head (phillips) SS| N/A|
| | |
Lower Assy.| Chain Tube, 56cm LDPE| TT000548|
| Chain Tube Clamp, Traveler| TT000422|
| Spacer, 20mnn L, 8mm AD x lOmm OD| TT000123|
| M5x18 Pan Head (Phillips) SS| N/A|
| M8x4Omm BHCS SS| TT000278|

Chain Routing
Cable Routing

Cable Routing RH
Brake Cable
Shift Cable
Chain Routing
Cable Routing LH
Cable Routing LH
Installation of Enviolo System
(Refer to https://support.enviolo.com/hc/en-us/sections/360003243600 -Assembly-documentation)

NOTE: Depictions of the Envelop Shifter may vary, but the installation process is the same.

The ROGUE comes stock with the Envelop CT system. Setup process is the same for all Enviolo shifters.
Products Overview
Route cable housing from the controller to the manual hub interface. Make sure that the cable housing lengths are sufficient to allow an extreme turning angle. Secure cable housing to the cable guides on mainframe. Avoid tight bends when installing the shift cable housing.

Thread both barrel adjusters completely clockwise (in) to provide maximum installation slack. Pull the under drive shift cable (1) firmly at the rear axle location until it stops, checking to make sure that the shift indicator goes completely flat (envelop TR and SP controllers), or that the grip rotates fully in the counterclockwise direction shown (envelop CT, CA and CO controller, viewed from the right side of the trike).
installation slack
installation slack
Pull the overdrive shift cable (2) firmly at the manual hub interface until it stops, checking to make sure that the shift indicator goes into a steep hill (enviolo TR and SP controllers), or that the grip rotates fully in the clockwise direction shown (enviolo CT, CA, CO controllers, viewed from right side of bicycle).
installation slack
Cable slack can be adjusted with the barrel adjusters (7) at the controller.
installation slack
Place the rear wheel into the rear frame, making sure not to obstruct shift cables.
Ensure cable housing is properly seated in controller. Double check overdrive and underdrive cable lengths before installing into shift interface. Overdrive (latch cable stop) 114mm from end of cable housing to latch cable stop. Underdrive (barrel cable stop) 120mm from end of cable housing to stop.
installation slack

www.TerraTrike.com | 800.945.9910

800.945.9910 | www.TerraTrike.com
4460 40th St. SE | Grand Rapids, MI 49512 USA
Symbols

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals