JVM6175DK Range Sensor Microwave Oven Installation Guide
- June 14, 2024
- GE
Table of Contents
JVM6175DK Range Sensor Microwave Oven Installation Guide
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
NOTE: Requires 120V grounded outlet. Electrical receptacle must be located in cabinet above microwave oven. No additional wiring, venting or cabinet rebuilding necessary in many cases. Complete detailed, easy-to-follow installation instructions and convenient, full-size templates are packed with the microwave oven.
IMPORTANT INFORMATION:
When installing the microwave oven over a range, allow minimum of 2″ from bottom of microwave oven to top of range blackguard to allow for removal of light covers.
VENTILATION OPTIONS:
The microwave ovens are designed for adaptation to the following three types of ventilation:
- Outside exhaust (vertical – as shown)
- Outside exhaust (horizontal)
- Recirculating (non-vented ductless – see Filter Kit drawing)
INSTALLATION INFORMATION:
This information is not intended to be used for installing unit described. Before installing, consult installation instructions packed with product/kit for current dimensional data
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
HOOD EXHAUST DUCT:
Outside ventilation requires a HOOD EXHAUST DUCT. Read the following
carefully.
EXHAUST CONNECTION:
The hood exhaust has been designed to mate with a standard 3-1/4″ x 10″
rectangular duct. If a round duct is required, a rectangular-to-round
transition adaptor must be used. Do not use less than a 6″ diameter duct.
REAR EXHAUST:
If a rear or horizontal exhaust is to be used, care should be taken to
align exhaust with space between studs, or wall should be prepared at the time
it is constructed by leaving enough space between the wall studs to
accommodate exhaust.
MAXIMUM DUCT LENGTH:
For satisfactory air movement, the total duct length of 3-1/4″ x 10″
rectangular or 6″ diameter round duct should not exceed 140 equivalent feet
ELBOWS, TRANSITIONS, WALL AND ROOF CAPS,
etc., present additional resistance to airflow and are equivalent to a
section of straight duct which is longer than their actual physical size. When
calculating the total duct length, add the equivalent length of all
transitions and adaptors plus the lengths of all straight duct sections. The
chart below shows the approximate feet of equivalent length of some typical
ducts
| DUCT | EQUIVALENT FEET |
|---|---|
| A. Rectangular-to-round Transition Adaptor | 5 ft. |
| B. Wall Cap | 40 ft. |
| C. 90° Elbow | 10 ft. |
| D. 45° Elbow | 5 ft. |
| E. 90° Elbow | 25 ft. |
| F. 45° Elbow | 5 ft. |
| G. Roof Cap | 24 ft. |
OPTIONAL ACCESSORIES
- Filler Panel Kit JX36BWW/ BBB/BSS/BES/BTS When replacing a 36″ range hood, this kit fills in the additional width to provide a custom built-in appearance. For installation between cabinets only; not for end-of-cabinet installation. Each kit contains two 3″-wide filler panels
- Filter Kit WB02X35687 (included) Recirculating Charcoal Filter Kit To be used when the microwave oven cannot be vented to the outside.
FEATURES AND BENEFITS
1.7 cu. ft. capacity – 1000 microwave watts (IEC test procedure) Weight and time defrost – Simply enter the weight of the food, and the oven automatically sets the optimal defrosting time and power level or set your desired time for defrosting “Add 30 seconds” button – Add 30 seconds of microwave cooking time
Two-speed, 300 CFM venting system – Removes smoke, steam and odors Upfront
charcoal filter with indicator light – Light indicates when odor-removing
charcoal filter needs to be replaced Turntable with on/o – Controls turntable
operation Sensor cooking controls – Automatically adjust time and power for
delicious cooking results
Model JVM6175DKBB – Black
Model JVM6175DKWW – White
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>