PETKIT 5-IN-1 Pet Grooming Kit Instruction Manual
- June 14, 2024
- PETKIT
Table of Contents
PETKIT 5-IN-1 Pet Grooming Kit
REMINDER
Before use:
- Press the PUSH button on the front side of the dust cup
- After the dust cup is lifted slightly, it can be removed
- Open the dust cup buckle and take out the functional parts
PRODUCT LIST
Functional parts
Accessories
PRODUCT INSTALLATION
-
Dust cup installation
-
Align the dust cup buckde with the main device slot
-
Press the end of the dust cup until heard a “click” sound, which means the installation is successful
-
Soft hose installation
Align point A of the hose with the hose connector point B , after inserting screw it clockwise to the end to ensure that the point C is aligned with point B
-
Functional parts installation and removal (The following picture uses electric clippers as an example, and the installation method of other functional parts is the same)
-
Functional part installation: Insert the hose connector Into the functional part and fasten tightly
-
Functional part removal: Press the button on the hose lightly to remove the functional part
-
Assembly completed****
During use, the hose must not be folded or squeezed, otherwise it will affect normal usage.
PRODUCT USE **
**
- Turn on device and mode selection
- Insert power cable, press On/Off button to start the device
- 3 suction level to select
-
Note: The product has a voltage error protection setting, when the indicators flash at the same time, and there is a “drip” sound when pressing the button. Please check whether the power input voltage is wrong. 2. Electric clipper
Can be used for daily fur trimming, the body fur trimmer can shave body fur, and the Power trimmer can shave paw fur and fur around the eyes.-
Buttons and indicator light description
To avoid damage to the product, please use a power adapter with output of DC 5V 1A for charging
-
Comb attachments use
-
Replacement of trimmer
Step 1: Turn the attachment counterclockwise to the end and take it out upwards.
Step 2: Vertically install the replacement attachment at an angle of 45′, and rotate it clockwise to the end. -
Electric trimmer use instructions
“Note: Remember to pay attention to the clipper edge and sharp position during use, and don’t use excessive force to avoid skin scratches.
-
Grooming brush
Can clean the remaining loose fur and dandruff on the pet’s body, and also
pulls the fur, making the fur more fully.
- Press the HOLD button and push it forward to the end, then push the HOLD button downward to complete the locking before start use
- Install the Grooming brush on the hose, turn on the device, and comb along the direction of pet fur
- When the Grooming brush accumulates a certain amount of fur, push the HOLD button up to unlock the comb, and push it forward repeatedly until the fur is sucked into the dust cup
Deshedding brush
Can comb away remaining fur and dandruff, and can thin and unknot the fur.
- Press the HOLD button and push it forward to the end, and then push the HOLD button downward to complete the locking before use
- Install the Deshedding brush on the hose, turn on the device, and comb along the direction of pet fur
- When the Deshedding brush accumulates a certain amount of fur, push the HOLD button up to unlock the comb, and push it forward repeatedly until the fur is sucked into the dust cup
Crevice tool
Can be used to clean fur, small objects and dust in the corners of carpets and
sofas
MAINTENANCE & CLEANING
- Dust cup cleaning
- Press the PUSH button and wait for the dust cup to lift up slightly to remove the dust cup
- After opening the dust cup lid, remove the fur and clean the dust cup
- Align the dust cup buckle with the slot of the main device, and then press the end of the dust cup. After heard a “click” sound, the installation is successful
- Electric clipper cleaning
- Push out the blade on the front side of the trimmer in the arrow direction
- Turn on the device, use the hase to suck off the residual hair on the body fur trimmer, body fur clipper holder, Paw trimmer and electric clipper main body
- Insert the bottor point D of the clipper blade into the groove point E of the clipper holder (as shown in the picture), press the clipper blade until heard a “click” sound, then the installation is successful
- Filter cotton cleaning
- Turn off pawer supply, remove dust cup and filter cotton
- Rinse the filter cotton in cold water and gently wring it out
- Place in a ventilated place to dry for more than 24 hours until completely dry
- Place the dried filter cotton back on the dust сир
- Hepa filter screen cleaning
- Tum off the power, take out the dust cup and the Hepa filter screen
- Rinse the Hepa filter screen with cold water and dry it after washing
- place in a well ventilated area to dry for over 24 hours until completely dry
- Install the dried Hepa filter screen back
Note: the front is facing outward (the lettering is on the front!
BASIC SPECIFICATIONS
- Main device parameters****
- Electric clipper parameters****
ASTOMERTO OUR VALUED CUSTOMERS
- Thank you for purchasing PET GROOMING KIT (PETKIT AIRCLIPPER 5-in- 1). We at PETKIT have done our best to make life easier for you and your pets with technology.
- Please carefully read the User Manual before using the product. By setting up and using this product, you acknowledge that you have already read and accepted the safety guidelines listed below.
- We are not liable and will not accept responsibility for any accidents or injuries that result from improper use of this product.
- PETKIT reserves the rights of interpretation and revision.
USER SAFETY GUIDE
Failure to follow the safety guides outlined below result in product malfunction, or other accidental losses.
- This device is only suitable for indoor use in a dry environment, do not use it on wet ground.
- Please place the device on a hard and flat surface for use, and do not place on a soft and uneven object to prevent the device from falling.
- Do not use or store this product in damp places such as outdoors or bathrooms.
- It is forbidden to suck in wet hair and liquid, so as not to cause device short circuit.
- The device is to be used on cats and dogs over 6 months old.
- Minors are prohibited from using this device.
- Do not operate with wet hands or unplug the power cord to avoid malfunction and electric shock.
- Before use, please make sure the air inlet is not blocked.
- It is forbidden to use this product in areas with flammable liquids or combustibles, and do not suck in highly flammable items [such as cigarette butts, etc.), so as not to cause fire or explosion.
- The product may have a strange smell during first time use, but it will not cause any adverse effects on your pet, and the smell will disappear after a period of time, thank you for your understanding.
- If the device has a persistent burnt smell, stop use immediately!
- Please clean the dust cup and filter cotton regularly to avoid excessive dirt buildup and device malfunction.
- During maintenance and cleaning, please make sure that the power cord is removed.
- If the device temperature rises abnormally during use, please stop use immediately.
- Do not pinch or pull the power cord, and do not place heavy objects on top of the device.
- If the device motor heats up abnormally or the air inlet is blocked, please stop use immediately, take out the dust cup, make sure the air inlet and filter cotton are clean, and turn on the device after 60 minutes.
- Before use, please ensure that the filter cotton and filter screen have been installed to avoid damage to the motor.
- Pets biting the electrical wire will cause electric leakage, please ensure pet safety.
- For prolonged storage, please switch off the power first and then unplug the power cord.
- Please do not place it in direct sunlight and keep it away from ignition sources.
- Please do not use this product if the power cord or power plug is damaged.
- Do not soak this product in water.
- Do not stack items on top of the device.
- Please use the provided power cord, otherwise, it will damage the equipment or cause potential safety hazards.
- Do not disassemble the equipment without authorization, and must be repaired under the guidance of professionals to avoid accidental injuries.
- If you encounter any problems while using this product, please contact us immediately.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and ;
- This device must, scoept, any interference received, including interference that may cause undesired operation.
FCC
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FOC Rules. These Emis are designed to provide reasonable protection against hammi. interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet RF exposure requirements.
This equipment complies with FOC radiation exposure limits set forth for an
uncontrolled environment. This equipment should
be installed and operated with a minimum distance 200m between the radiator &
your body E warning
This device complies with Industry Canada Fence-event F$5 standards. Operation is subject to the following two conditions
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>