heysong C1j2JWdFlDL Portable Bluetooth Speaker User Manual
- June 14, 2024
- heysong
Table of Contents
THE HEYSONG REVERB SPEAKER
USER MANUAL
INTRODUCTION
Thank you for choosing the Bluetooth Speaker as your source for entertainment!
This speaker can be used via a Bluetooth connection with a tablet, some
computers and some smartphones to stream music and make wireless telephone
calls. To make the most of the features of your speaker, we recommend that you
carefully read this user guide first.
IMPORTANT WATERPROOF / SAFETY INFORMATION
HEYSONG REVERS is rated IP67, which means the speaker can be heavily splashed
with water or left in the rain, even can submerge in 1 meter of water for 30
minutes. If the speaker gets wet, it is recommended that you dry the speaker
completely before using it again. Please note:Please make sure that cover is
closed and secure before using in a wet environment. Please don’t take off the
silicone case of the speaker, when put the speaker into the water.
CONTENT HEYSONG REVERB SPEAKER x 1
USB-Charging cable x 1
AUX-IN cable x 1
Strap x1
Manual x 1
SPECIFICATION
Built-in Battery: Li-ion5000mMAh
Dimensions: L173W74H67mm
Wireless Working Frequency: 2.402-2.480 GHZ
Wireless Transmission Distance: up to 10m
Weight: 430g
Charging: 5V, 2A
DESCRIPTION
- ON/ OFF/ Light switch
- Volume decrease/ Previous track
- Volume increase/ Next track
- Play/Pause/ TWS
CHARGING
- Connect one end of the inctuded USB Charging Cable to the Charging Port on your speaker. Then plug the other end of the USB Charging Cable into a suitable USB port on your computer, notebook or power bank to recharge your speaker’s internal rechargeable battery.
- When charging, a red LED light will illuminate to indicate that the unit is charging. The red light will turn off when your unit is fully charged.
Tips:
- You will hear a “low battery” prompt when battery is low and needs to be recharged.
- To protect the battery’s durability, fully charge the speaker if it is not used for a long time.
- The internal battery of your speaker takes approximately 4 hours to be fully charged.
BLUETOOTH MODE
To pair your Bluetooth audio device to your Bluetooth Speaker for the first time. Please follow the steps below:
- Make sure your Bluetooth device is held within three meters of your speaker.
- Press and hold the “ ” button for 3 seconds to turn on your speaker. It wilt go into pairing mode, and the blue indicator will keep flashing.
- Activate Bluetooth on your device and search for other devices. Once you have found *HEYSONG REVERB’ on your Bluetooth device, click it for pairing.
Note:
This speaker will pair with the last connected device when that device is in
range.
The speaker will be turned off if no device has been paired for more than 10
minutes.
HANDSFREE EQUIPMENT
You have the option to use the sound trip as a hands-free device.
1, When a call comes in, the music is automatically interrupted. Answer or
hang up the call by pressing the” &” key once.
2. Music playback will resume when your call ends.
3. To reject an incoming call, press and hold the * & “key.
TWS FUNCTION
If you have two of HEYSONG REVERB, you can use the following steps to achieve wireless stereo pairing.
- Power on both speaker and make sure your speakers are not connected to other devices yet.
- Press* “button on one of the speakers, the two speakers will connect automatically with indicated tone. You will see a blue LED blinks quickly on one unit and solid blue LED on the other one.
- Search Bluetooth device on your audio source and select “HEYSONG REVERB.”
- When your speaker is successfully paired with the audio source, the indicator light will remain solid blue.
- Long press the “* “on one of the speakers to disconnect the TWS connection.
- Long press the “ ” again on one of the speakers to disconnect the Bluetooth from the device,
AUX IN MODE
Connect the item and the speaker with the 3,5 mm AUX-In cable.
Control the music playback as follows.
PLAY MUSIC → Press“ & “to start the music and stop the music.
MUSIC FORWARD OR RETURN → Press and hold the “ + “or * – “buttons.
REGULATE VOLUME → Press the “ + “or” – “buttons.
TF CARD MODE
Once a TF Card inserted, the unit will turn into TF Card mode and plays music
automatically. The LED light will change to green light.
Press the“ ” to change the mode between Bluetooth and TF mode.
RGB LIGHT
Press the“ “button twice to select the sidelight mode.
TROUBLESHOOTING
Problem | Solution |
---|---|
The speaker doesn’t connect to device. | Speaker needs to be connected/re- |
paired to device.
A voice “low battery” is heard every few seconds.| Speaker needs to be
charged.
Bluetooth connection distance cannot reach to 33ft.| Avoid operating the
Bluetooth speaker in areas of strong electromagnetic Interference,such as near
induction cookers,large power fans,motors etc. Move the speaker closer to
Bluetooth device. Fully charge the speaker and try again.
The speaker will not power on.| Speaker needs to be charged.
The speaker doesn’t control track(s)/volume.| Speaker needs to be in Bluetooth
mode for full control.
The speaker distorts at high volume.| The devices’ volume needs to be lowered.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>