ILROOMH SFS-1016 Rain Shower System Instruction Manual

ILROOMH SFS-1016 Rain Shower System Instruction Manual

Warranty Duration

Ail parts of this faucet system are warranted to the original purchaser to be free from defects in material and workmanship for a lifetime.

Repair and Replacement

f the product has defects in material and workmanship within the warranty period, we will repair or replace the product free of charge.However,you may be required to provide the invoice when requesting repairs or replacement from us.

Exclusions

We shall not be responsible for the following cases:

• Damage to the product caused by improper installation,misuse,unauthorized repair or
  replacement, or abuse(including damage during shipment).

• Damage to the product caused by improper dismantlement after installation.

• Damage resulting from abnormal water pressure and impurities in water pipes is not
  covered under this warranty.

• Rust on the product due to insufficient care and maintenance is not covered under
  this warranty.

• Damage caused by natural disasters such as fire,flood,earthquake,electric storms, etc., is not covered under this warranty.

I hope this helps! If you have any further questions or concerns, please let me know.

Installation Condition

1. .Check the accessories list to verify that all parts are complete in this package.
2. Do notdisassemble the main body by yourself.
3. Connect inlet pipes to supply valves.
4. Make sure inlet pipes and supply valves have no impurities and are cleaned, with no impurities in the pipeline.
5. After installation, check all joints for leakages.
6. Do not leave the rain shower system exposed to a severely corrosive environment.

YOU MAY NEED:
VOUS POURRIEZ AVOIR BESOUE:

functions wall mounted luxury shower faucet
Model :A
Accessories List

Essential dimensions & water pipe line

The installation depth of shower holder and body jet

The thickness of the tile must be calculated for installation.
Connector size of male thread: USA: 1/2″-14NPT, Canada: 1/2″-14NPT, Europe: G1/2″

Installation Depth Of Main Body

Notice:

1. The installation depth of the main body should be no less than 2 9/16″ (65mm)  and no more than 3 17/32″ (90mm), including the thickness of the tile. Otherwise, the deck plate cannot be installed.
2. The opening size of ceramic tile shall be smaller than the deck plate size.

Piping Instructions Before Tiling

1. .As shown in the figure, the inlet and outlet pipes are pre-buried. Please pay attention to the correct direction when installing the pre-buried main body.
2. Before tiling, turn on the water to test whether the left and right inlet pipes are tightly connected without leakage. Then, adjust the flow switch 1o the “on” position to check for leaks in the mixed outlet pipes.

Main Body Valve Installation

• (Concrete wall) (Mur eon baton)

• (wood wall) (murk de bios)

1. Make marks according to the size of the main body valve, and then drill anchors into the wall (concrete wall).
2. Lock the main body to wood directly with screws (wood wall).
3. When installing the main body, please mark the UP side up and do not install it upside down.
   A Please note that the level meter should be parallel to the wall; otherwise, the deck plate cannot be installed

Step2
Étape2

Do not remove the white wear ring; otherwise, the. handwheel will be damaged.

1. Please install the deck plate, water diverters, and water diverter rods step by step.
2. Install the handle with the screw and handle cap.

Precautions for Handwheel Installation

1. The line can’t be misplaced; it should be kept in line. Otherwise, Etape2 the water temperature of 100°F or 38°C will not be correct.

2. Please ensure that the plastic locating ring (A) and handwheel locating pin (B) are kestin the same line with 100°F or 38°C. Otherwise. the water temperature will be incorrect.
   

Body Jets Installation(Model :A &B)

Step 1.Wrap the threaded pipe of NPT 1/2 with Teflon tape and screw it into the wall.
Step 2.Cut off any excess parts using a saw.
Step 3.Screw the massage body jet onto the wall.

Installation of the Hand Shower Holder

Female thread elbow

1. .Connect shower arm with the cover before screwing arm into riser connection to prevent damage.
2. Fix shower head onto shower arm and apply tape to pipe threads on both ends.
3. Do not overtighten shower head.it is 360°swivel connection

Lifting Rod Installation

Step1.The connector to be wrapped with Teflon tape, crew the thread into the water pipe inside the wall.
Step2.Install the rubber pad on the shower hose and connect it with the connector

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>