HEYSONG B18H Shower Speaker User Manual
- June 14, 2024
- heysong
Table of Contents
B18H Shower Speaker
User Manual
INTRODUCTION
Thank you for choosing the Speaker as your source for entertainment! This speaker can be used via a connection with a tablet, some computers and some smartphones to stream music and make wireless telephone calls. To make the most of the features of your speaker, we recommend that you carefully read this user guide first.
IMPORTANT WATERPROOF / SAFETY INFORMATION
HEYSONG AQUA is rated IPE7, which means the speaker can be heaviy splashed
with Water or eftin the rain, even can submerge in 1 meter of water for 30
minutes. Ifhe.
speaker gets wel, itis recommended that you dry the speaker completely before
using it again Please note:Please make sure tha cover is closed and secure
befor using in @ wet environment. Please don’ take off the silicone case of
the speaker, when put the speaker into the ater.
SPECIFICATION
Loudspeaker. 40 W
BuitinBattery: Li-in2000mAn
Dimensions: 1 mim (L)*99mni(W)Sénim(K)
SNR: 8248
Wieless Working Frequency. 2.402-2.480 GHZ,
Wireless Transmission Distance: up fo 10m
ChargingTime: 3-Ghours.
Weight 2209
Speaker Dimension: 50mm
Charging: SV@IA
PACKAGE CONTENTS
IMPORTANT SAFETY PRECAUTIONS
When using your Blustooth Mobile Speaker, basic safety precautions should always be followed, ncluding the following
- Keep this product and its charging cable away rom excessive heat
- Donot operate this device with a damaged cable or after it has malfunctiond or has been damaged in any manner.
- D0 not disassemble your device
CHARGING YOUR SPEAKER
-
Connect one end of the ncluded USB Charging Cable to the Charging Port an your speaker. Then plugthe other end of the USE Charging Cable into a suitable USB port on your computer to recharge your speakers internal rechargeable battery.
NOTE: The internal battery of your speaker takes approximately Three hours to charge when completely drained. -
when charging, ared LED liht will iluminate to indicate that the unitis charging The red liht will tun of when your uit s fuly charged.
Tips:There will be a beep when the battery is ow and needs o be recharged.To protect the the battery’s durabily,fully chaise the speaker if it s not used for a long time.
A QUICK LOOK AT YOUR DEVICE
-
Previous: Press and hold 1o access the lasttrack in playlist Press 10 lower the volume.
-
Next: Press and hold to access the net track in playlist Press to increase the volume.
-
ON/OFE swich (PloyPavse)
Press and hold the for power on
Fressand hold the “agel o pover off Press this button o activate the speaker phone function.
When music i playing,press to play or pause track. -
Light Change
Short press this button to cycle through 5 light modes.
Under the playing music matle, you can press and hold the light button to enter the light lash with music mode. -
ChaningPort/Aux-in
You ca plug Gne end of the ncluded USE Charging Cable ino this ack. whie plugging he ather end ntoa USES Eiper % or o o Gha G o Speakers Bt Uthium bettery.
UNDERSTANDING THE LED STATUS LIGHTS
When Charging Your Speaker
Solidred LED – Charging
No red LED = Charge Complete
When Pairing Your Speaker To A Bluetooth Audio Source
Rapid blinking blue LED: Blutooth not connected.(Ready to poir) Solid blue
LED: Bluetooth comnected.
AUX-IN MODE
- Power onthe Blue LED stay iluminated.
- Plug in the supplied 3.5mm cable into the unt. The other end is connected to your device.
- The blue LED willblink siowly t indicated that you have entered Aus-In mode.
PAIRING BLUETOOTH DEVICES TO YOUR SPEAKER
In order to pair your Bluetooth audio device to your Bluetooth Speaker for the first time, follow the steps below:
- Make sure your Bluetooth audio source is held within three meters of your speaker.
- Press and hold the“ ”switch on your speaker to power on The LED light will blink blue to indicate that you have entered pairing status.
- Go to the Bluetooth Manager of your Bluetooth audio source. Please refer to the User’s Manual of your Bluetooth audio source for more information.
- Search Bluetooth devices and select“HEYSONG AQUA”.
- Once paired, the blue LED light will be solid and you can use your speaker to listen to audio from you Bluetooth sound source.
NOTE ：Press the“ ”twice to disconnect the Bluetooth
USING THE HANDS-FREE FUNCTION
When an iPhone or other smartphone is connected to your speaker follow the steps below to take calls hands-free.
- Press“ ”o pick up the call.
- Press and hold“ ”to reject the call.
- During call: Press“ ”again to hang up the call.
TWS FUNCTION
If you have two of HEYSONG AQUA, you can use multiple point to achieve wireless stereo combined playing music.
- Make sure two HEYSONG AQUA are without any Bluetooth connection.
- Power on both units and press“ ”button on the speaker, the two speakers will connect automatically with indicated tone. When blue LED blink quickly on the one unit and solid on the other one,it means the multiple point connection is successful.
- Under connection, search Bluetooth device and select“HEYSONG AQUA”
- When the device and the units are connected, the blue LED of both units will be solid.
- Press the“ ”button twice to disconnect the TWS connection from the units.
- Press the“ ” button twice again to disconnect the device from the unit.
TROUBLESHOOTING
| Problem | Solution |
|---|---|
| The speaker doesn’t connect to device | Speaker needs to be connected/re-paired |
to device
A tone is heard every few seconds| Speaker needs to be charged
Bluetooth connection distance cannot reach to 33ft.| Avoid operating the
Bluetooth speaker in areas of strong electromagnetic Interference,such as near
induction cookers,large power fans,motors etc. Move the speaker closer to
Bluetooth device. Fully charge the speaker and try again.
The speaker will not power on| Speaker needs to be charged
The speaker doesn’t control track(s)/volume| Speaker needs to be in Bluetooth
mode for full control
The speaker distorts at high volume| The devices’ volume needs to be lowered
US ：[email protected]
UK：[email protected]
Website ：www.iheysong.com
https://www.iheysong.com/pages/certifications