ATEL V810V Axis 4G LTE Home Phone Connect User Guide
- June 4, 2024
- ATEL
Table of Contents
V810T 4G LTE Phone Hub
User Guide
Models Covered:
| Model | LTE Bands |
|---|---|
| V810T | B2/4/5/12/66/71 |
| V810V | B2/4/5/12/13/66/71 |
A quick look at your device:
1. LCD Display Displays Home and Device Information display screen| 5. SIM
Card Slot As needed, insert your 4FF Nano SIM card into this springloaded SIM
slot.
To remove it, press the SIM inward.
---|---
2. Power Button Power the V810 On/Off by pressing and holding this button for
up to 10 seconds.
Short press to wake up the screen.| 6. Type C Port Use this port to connect
the USB-C cable to a wall adapter for external power.
3. Battery Port connects to the AA battery (AA batteries Included) holder or
a Ni-MH rechargeable battery pack (sold separately).| 7. Phone Port (RJ11)
Use a telephone cord to connect your telephone base to this port.
4. Reset Button Use a pin to push and hold this button for 3 seconds for a
factory reset.| 8. Antenna Connector Install an optional antenna (sold
separately) to increase signal strength. You may have to pull off the back
rubber cover prior to installing it.
Setting up your V810
Install SIM Card
a) Remove the back cover.
b) Carefully lift the battery holder from the side.
c) Check for a pre-installed SIM card or install a SIM card provided by your
wireless carrier.
d) To install, insert the 4FF SIM card into the springloaded SIM slot as the
image shows.
To remove a SIM, press the edge of the SIM inward and the SIMwill pop outward
from the slot.
Install Battery
Remove the battery cover. Properly align and install 3 AA batteries into
the battery holder. Put the battery cover back in place as shown in the image.
Alternatively, a Ni-MH rechargeable battery pack (sold separately) can be
connected to the Battery Port.
Note: During a power outage or if the wall charger is unplugged, the V810
continues to run off the batteries to support Voice.
During a power outage, only corded phones that do not require electric power
can be used to make or receive calls (including calls to 911).
Equipment External Power
To connect your V810 to the power outlet, insert your USB cable into the
device’s USB-C port and plug the other end into a wall adapter.
WARNING! Please only use the provided USB adapter for the V810. The use of other incompatible adapters may cause damage to your device and void the warranty.
Turning your V810 On/Off
To turn on your V810 press and hold the Power button.
To turn off your V810, press and hold the Power button until you see the
screen turn of.
Optional Add-Ons: Install an Antenna
To increase signal strength, you can install an optional antenna.
- Align the antenna with the antenna port and screw securely into place (in a clockwise direction).
- Restart the V810 after the antenna is installed.
Note: Antenna sold separately. Using optional accessories (antenna and battery pack) by ATEL are recommended, available at ATEL website, https://www .atel-usa.com/.
LCD Display Icons Overview:
| Icon| Definition
---|---|---
Network Signal| | Indicates the signal strength of your wireless provider in
your location. More bars represent a stronger signal.
Battery| | Battery Level (Applies to NiMH Battery Only)
| Batteries Not Installed
| Battery Charging (Applies to NiMH Battery Only)
TTY| | In TTY Mode
Power Key| | Press the Power Key to switch menu screens.
Connect your Telephone to the V810
The V810 provides 2 telephone ports (RJ11). The ports use the same telephone
number.
Plug the telephone cord into one of the telephone ports on the back of the
V810 (the other end of the cord must remain plugged into the back of your home
telephone base unit).
Note: The telephone and telephone cord are not included.
Make Calls
Before making a call, make sure at least one of the signal strength indicator
bars ( ) is lit up. If no signal bars are lit, move the V810 to a location
that can receive a signal.
Pick up the handle of your telephone then dial the number to use call
services.
Using a Text Telephone
To use the V810 with TTY, you must first change the TTY mode from the default
(None) to one of the following modes. From the connected telephone dial pad,
dial “##56*n#” where “n” indicates the TTY mode:
0 – None (TTY) is disabled
1 – Full TTY Mode
2 – VCO mode
3 – HCO mode
Online Device Management Portal
You can access your V810 Online Portal to view your device status, change your
device settings, and perform manual software upgrades.
- First, connect your V810 to a computer with a USB-C cable and then enter http://192.168.0.1 in the browser URL address bar.
- The login username is “admin”. The unique password can be found on the device label (under the battery holder).
Online Device Management Portal
From the HOME menu, you can view your device information and network status.
Go to the ABOUT menu to check for remote software upgrades.
For more information
Please refer to your V810 User Manual for additional information or visit the
ATEL USA website Device and Support pages at www.ATEL-USA.com.
https://www.atel-usa.com/v810-axis Our Website: www.atel-
usa.com Contact us at: support@atel-
usa.com
For Warranty information, see our website under the Support tab.
© 2022 Asiatelco Technologies, Inc. All Rights Reserved PN
YS0344T002
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>