ATEL V810T 4G LTE Phone Hub User Guide
- June 4, 2024
- ATEL
Table of Contents
V810T 4G LTE Phone Hub
User Guide
Models Covered:
| Model | LTE Bands |
|---|---|
| V810T | B2/4/5/12/66/71 |
| V810V | B2/4/5/12/13/66/71 |
A quick look at your device:
1. LCD Display Displays Home and Device Information display screen| 5. SIM
Card Slot As needed, insert your 4FF Nano SIM card into this springloaded SIM
slot.
To remove it, press the SIM inward.
---|---
2. Power Button Power the V810 On/Off by pressing and holding this button for
up to 10 seconds.
Short press to wake up the screen.| 6. Type C Port Use this port to connect
the USB-C cable to a wall adapter for external power.
3. Battery Port connects to the AA battery (AA batteries Included) holder or
a Ni-MH rechargeable battery pack (sold separately).| 7. Phone Port (RJ11)
Use a telephone cord to connect your telephone base to this port.
4. Reset Button Use a pin to push and hold this button for 3 seconds for a
factory reset.| 8. Antenna Connector Install an optional antenna (sold
separately) to increase signal strength. You may have to pull off the back
rubber cover prior to installing it.
Setting up your device:
Step 1: Insert a SIM (if applicable)
a) Remove the back cover.
b) Carefully lift the battery holder from the side.
c) Check for a pre-installed SIM card or install a SIM card provided by your
wireless carrier.
d) To install, insert the 4FF SIM card into the springloaded SIM slot as the
image shows.
To remove a SIM, press the edge of the SIM inward and the SIMwill pop outward
from the slot.
Step 2: Install the Battery
We recommend installing the 3 AA batteries prior to use, even if you plan on
Powering your device via the USB-C cable. Checking and changing the 3 AA
batteries regularly is also suggested.
a) Remove the battery cover.
b) Properly align and install 3AA batteries into the battery holder. AA
batteries are included with your device.
c) Put the battery cover back in place as shown below.
Make sure that the back cover is flush with the bottom of the device.
Step 3: Power on the Device
To connect your V810 to the power outlet, insert your USB cable to the
device’s USB-C port and plug the other end into a wall adapter.
Press and hold the Power Button for up to 10 seconds on your V810 to turn on
the device.
As the device boots up, you will see the Welcome screen on your V810 LCD
display, followed by the status bar display.
WARNING! Please only use the provided USB adapter for your V810. The use
of other incompatible adapters may cause damage to your device and void the
warranty.
Step 4: Connecting a Telephone to your V810
a) Complete Steps 1, 2, and 3 above.
b) Plug one end of the telephone cord into the RJ11 Phone Port of your V810
and plug the other end of the telephone cord into your telephone base.
Note that the two RJ11 ports use the same telephone number. 
Note: The telephone and telephone cord are not included.
Step 5: Initial Activation
Once the above 4 steps are completed, with a service plan subscription,
your V810 with automatically detect the wireless network and activate the SIM
card services. The wireless network and signal strength indicator will appear
on the status bar of your Welcome Home screen. It might take a few minutes for
the initial activation.
If your V810 cannot detect any network services or if you have SIM card
issues, please contact your wireless service provider.
Step 6: Making Calls
a) Before making a call, make sure at least two of the signal strength
indicator bars ( ) are lit up. If no signal bars are lit, move the V810 to a
location that can receive a signal.
b) Pick up your telephone and dial the number to place a call.
For more information
Please refer to your V810 User Manual for additional information or visit the
ATEL USA website Device and Support pages at www.ATEL-USA.com.
https://www.atel-usa.com/v810-axis
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>