ATEL W01 Arch 4G LTE Mobile Hotspot User Guide

: June 13, 2024
: ATEL

ATEL W01 Arch 4G LTE Mobile Hotspot

ATEL W01 Arch 4G LTE Mobile Hotspot

Device Display

WARNING! Please only use an approved charger to charge your W01. Improper handling of the charging port, as well as the use of an incompatible charger, may cause damage to your device and void the warranty.

Key

Power Button

Power on/Arch for the W01 . Quick press the power key two times, start WPS.

Type C Charging Port

The USB charger connects here.

Battery

Insert the battery to align with the battery contacts.

Reset

To perform a reset of your device, use a unfolded paper clip to insert to the RST pin hole, and push down for 3 seconds, then release.

SIM Card

Remove the battery cover from the back of your W01 and remove the battery. Slide open the SIM door and insert your SIM as the image shows below. Make sure the SIM is placed properly before sliding the door back up to close the SIM door.

SIM Card

Setting up your W01 Arch

Wi-FI Network Name (SSID) / Password

You can locate the SSID and password on the device label in the battery compartment. Use the SSID/password to establish your internet connection.

$Wi-FI Network Name $SSID$ / Password$

http://www.atel-usa.com/

Turning your W01 On/Off

First, insert a compatible SIM card into your W01 Arch. Then insert the battery and close the battery cover. To turn your W01 Arch on, press and hold the Power button. To turn it off, press and hold the Power Button until you see all of the LED lights go up and off.

Charging your W01 Arch

To charge your device, insert the USB Type C cable into the charging port and plug into the charger.
The power/battery LED indicator will start blinking which indicates the device is charging.

Charging your W01 Arch

System Requirements

Your W01 Arch is compatible with any device with Wi-Fi capability and an Internet browser. It is compatible with all major operating systems and the latest versions of browsers.

Device Settings

You can access your Mobile Hotspot (W01 Arch ) Online Device Management Portal (Online portal) to view and edit your settings.

Connect your Wi-Fi capable device (e.g. laptop) to your W01 Wi-Fi
network
Open a browser (e.g. Chrome) and enter http://192.168.0.1 in the URL address bar.
For T-Mobile and all other users, enter “admin” for both username and password. For Verizon users, enter “admin” for username. For password, please check your device label for the unique Online Portal password.

You can change the Admin password from the hotspot Online Portal under SETTINGS > Device Settings. Once changed, you must use the new password to login to the Online Portal.

While different browsers may have different security settings for HTTPS, additional steps may be needed if you access the Hotspot Online Portal using https://192.168.0.1. For example, for Microsoft Edge browser, you will need to click “Advanced > Continue to 192.168.0.1 (unsafe)” in order to access the interface.
Device Settings

Managing Wi-Fi networks and Connections

From the Online Device Management Portal, you can change your Wi-Fi Settings. For example, the maximum Wi-Fi connection is defaulted to 15 and you can set it to any value between 1 and 15. The Wi-Fi band is defaulted to 2.4 GHz and you can change it to 5GHz.
Managing Wi-Fi networks and Connections

Connecting to the Internet

Open the Wi-Fi settings of your devices that you want to connect to the W01 Arch.
Select the SSID of your W01 from the available network list.
When prompted, enter your W01Arch password (located on the device label in the battery compartment).

Factory reset your W01 Arch

You can reset your W01 Arch to factory settings with the W01 Arch reset pin hole or via the Online Portal

NOTE: Resetting your W01 will disconnect all devices connected to your W01Arch . All device settings including network name and password will be reset back to factory defaults.

To reset from the Online Portal, lick About->Backup and Restore->Restore to Factory Defaults.
To reset using the reset pin hole on W01:

Make sure your W01 is on.
Remove the battery cover from the back of your W01 Arch.
Insert an unfolded paper clip into the Reset pin hole and press until the W01 Arch LED lights are out.

Connection LED Indicator

LED	Color	Action	Function Description
LTE/3G		On	Represents 5-bar signal
On	Represents 4-bar signal
On	Represents 3-bar signal
On	Represents 2-bar signal
On	Represents 1-bar signal
Blinking	Error, no SIM or no

internet
| Off| No Signal

Customer Support

Our Website: www.atel-usa.com
Contact us at: support@atel-usa.com
For Warranty information, please see our website under the Support tab.
© 2020 Asiatelco Technologies, Inc. All Rights Reserved PN YS0344T005