ErGear EGESD5B-1 48 Electric Standing Desk With Monitor Riser And Drawers Instruction Manual

48″ Electric Standing Desk
Instruction Manual
Rev00(A)
(EcESD5B-1/ EGESD5V-1

Technical Support:
(Us/cA) 1-800-651-9525
Mon~—Fri, 8am—-8pm (CST)
(UK) 44-808-196-3875 Mon—Fri, 2pm-10pm (UTC)
Other Info: support@ergear.com
Website: https://ergear.com

Specifications

Height Adjustment Range
28.3″-46.5″ (72-T18cm)

Step 1 Supplied Parts and Hardware

Step 2 Supplied Parts and Hardware

Step 3 Supplied Parts and Hardware

Step 4 Supplied Parts and Hardware

Step 5 Supplied Parts and Hardware

Step 6 Supplied Parts and Hardware

Assembling and Connecting the Desk Legs

Attaching the Side Plates and the Transmission Rod

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmis- sion rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.

Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.

Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.

Assembling and Attaching the Desktop

Assemble the desktop.

Secure the desktop panels with the connectors.

Assembling and attaching the Drawers

Attach the top panels of the drawers.

Secure the drawer top panels with the cam locks and screws. Then cover the cam locks with the caps.

Screw the cam bolts into the stand top panel.

Attach and secure the stand top panel with cam locks and wood dowel pins. Then cover the cam locks with the caps.

Attaching the Controller

Connecting the cables

Using the Controller

• Save Current Height Setting
  Short-press the   button, and the display will flash. Press the (1], (2], or [3] button to save the current height setting to that button.

• Select Height Setting 1
  Press the   button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 2
  Press the   button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 3
  Press the button, and the desk will move to the height that was previously set for that button.

• Raise the Desk
  Press the   button to raise the desk continuously until it reaches the highest position of 46.5” (118cm) or the button is released.

• Lower the Desk
  Press the   button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.

Settings

Change Display
Height Units| Press and hold the 0 button until a flashing ‘S-‘ is displayed.
Press again, and ‘Un’ is displayed. Press to select it press or to switch between ‘IN’ (imperial) and ‘SI’ (metric), and press to save your choice.
Change Collision
Detection Sensitivity| Press and hold the   button until a flashing ‘S-‘ is displayed.
Press again, and ‘Un’ is displayed. Press or to switch to ‘CF’ and press to select it. Press or to switch
between off, low, normal, and high sensitivity. Press **** to save your choice.

Reset| Press and hold the  button for 5 seconds, and the screen
will show ‘RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.
| Protection Mode Error Codes
---|---
Hot| Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
E10| Sensor malfunction Warning: motor safety sensor cora be detected. Power off, Mack the connection between the motor and controller, and power back on again
£20| Overloading Warning: Max load exceeded. if raising the desk, take the things off the desk and try again. II lowering the desk, power off, take the things off the desk power back or and Try again.
E02| Operation Status Warning: The Oe…k stops moving it vibration, Impact, or incline are detected. If this detection is Incorrect, follow the reset Instructions before continuing use.
E32| Ovewoltage Protection: Input voltage too high. It the correct *AC adopter Is being used, power of the de, check the connection between power and the controller, and power on again.
---|---
E 31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power of the desk, check the connection between power and the controller, and power on again.
E ea| Unequal Leg Height Warning Power off the desk and check whether the left and right legs are at the same height Adjust if necessary by folloWng the Instructions. Power on again.
–| Coble Disconnection Warning Check motor and controller cable connections. Normal operation should return once all connectors are properly connected**

Complete Flexibility.
Total Freedom.
Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.
Technical Support

(us/cA) 1-800-651-9525 Mon—Fri, 8am—-8pm (CST)
(UK) 44-808-196-3875 Mon—Fri, 2pm-10pm (UTC)

Other Info
support@ergear.com
Website
https://ergear.com
860-00288-04 Rev00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>