Westinghouse 5239000 LED 5 Inch and 6 Inch Retrofit Trim Instruction Manual
- June 4, 2024
- Westinghouse
Table of Contents
5239000 LED 5 Inch and 6 Inch Retrofit Trim
Instruction Manual
5239000 LED 5 Inch and 6 Inch Retrofit Trim
Please read carefully and save these instructions, as you may need them at a later date.
GENERAL: All electrical connections must be in accordance with local and
National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper
electrical wiring connections obtain the services of a qualified electrician.
Remove the trim from the box and make sure that no parts are missing by
referencing the PARTS illustrations.
THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LED LUMINAIRE WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR CANADIAN
AUTHORITIES HAVING JURISDICTION.
WARNING: RISK OF ELECTRIC SHOCK. INSTALL THIS TRIM IN RECESSED HOUSINGS THAT HAVE THE DIMENSIONS SHOWN IN FIG. 1.
WARNING – Risk of fire or electric shock. LED Retrofit Kit installation
requires knowledge of luminaire electrical systems. If not qualified, do not
attempt installation. Contact a qualified electrician.
WARNING – Risk of fire or electric shock. Install this kit only in the
luminaires that have the construction features and dimensions shown in the
photographs and/or drawings.
Do not make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to
the edges of sheet metal or other sharp objects.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED
ASSEMBLY AND INSTALLATION
INCANDESCENT HOUSINGS
1. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 2)
2. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the MALE CONNECTOR of
the SOCKET ADAPTER ASSEMBLY. (FIG. 3)
For the torsion spring option, please follow the below steps.
3a.Squeeze both TORSION SPRING arms together and insert them into the TORSION
SPRING SLOTS (or RECEIVER BRACKETS) of the recessed housing. Tuck all wires
into the recessed housing and carefully push the RETROFIT TRIM into the
recessed housing. (NOTE: To provide enough room in shallow cans, carefully
position SOCKET ADAPTER and SOCKET adjacent to the long side of the LED DRIVER
prior to inserting the RETROFIT TRIM into the recessed housing.) (FIG. 4a)
Note: This fixture is 5″ & 6″ compatible.
For 5″ installation, slide the springs to the position which marks 5″.
(Refer to Fig 5a, 6a, 7a & 8a)
For the clip option, please remove the torsion spring and replace it with
clips.
3b. Squeeze both clip arms together and insert them into the clip of the
recessed housing.
Tuck all wires into the recessed housing and carefully push the RETROFIT TRIM
into the recessed housing. (NOTE: To provide enough room in a shallow recessed
housing, carefully position SOCKET ADAPTER and SOCKET adjacent to the long
side of the LED DRIVER prior to inserting the RETROFIT TRIM into the recessed
housing.) (FIG. 4b)
Note: This fixture is 5″ & 6″ compatible.
For 5″ installation, slide the clips to the position which marks 5″.
(Refer to Fig 5b, 6b, 7b, 8b & 9b)
DIMMING
Although this product is compatible with most common residential type dimmers,
dimming performance depends on the dimmer, dimmer setting (for dimmers with
brightness range adjustments), wiring method, and the number of LED modules.
For best results, set the dimmer position at maximum before adjusting to a
lower light level.
Recommended Dimmers (minimum load for four LED modules may be required for
optimal dimming performance):
Lutron: TGCL-153P, DVCL-153P, CTCL-153P, MACL-153M, PD-6WCL;
Leviton: IPL06-10, 6672-1L, 6674-P0
LIMITED WARRANTY
This lamp is warranted to be free from defects in materials and workmanship
for 5 years.
If the product fails during the warranty period, return the defective product
to the seller.
Warranty terms and conditions of seller apply. If the replacement product is
not available through the seller, please contact www.westinghouselighting.com
/contact-us.
WARNING – RISK OF ELECTRIC SHOCK. DISCONNECT THE MAIN POWER AT THE FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE.
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
and Westinghouse are trademarks of
Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All Rights Reserved.
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>