VOLTCRAFT VC-12/1000A Car Emergency Battery Capacitor Jump Starter User Manual

VOLTCRAFT VC-12/1000A Car Emergency Battery Capacitor Jump Starter

Product Information

The VC-12/1000A Capacitor Jump Starter (Item no: 2799626) is a standalone vehicle battery jump starter. It uses a capacitor to capture and store residual energy from a weakened 12V battery, then releases that stored energy to crank start the engine. It is designed to be used on batteries with a voltage greater than 6V.

Key Features:

• LCD screen
• Power button
• Cable clamps
• LCD status indicator
• Input voltage/current: 12 V/10 A
• Output voltage: 12 V
• Start-up current: 500 A
• Peak current: 1000 A
• Capacitor: Charging time: approximately 3 minutes (for a 70-Ah battery), Lifetime: approximately 10,000 cycles
• Reverse polarity protection: yes
• (Short circuit protection): yes
• Dimensions (W x H x T): 136 x 57 x 200 mm
• Weight: 1.00 kg

Product Usage Instructions

1. Before using the VC-12/1000A Capacitor Jump Starter, ensure the vehicle’s engine and electronics are turned off.
2. Connect the cable clamps to the battery terminals, ensuring proper polarity.
3. Press the power button to activate the LCD screen.
4. Check the battery voltage displayed on the LCD screen.
5. If the battery voltage is below 13 V, prepare the capacitor by allowing it to charge for approximately 3 minutes.
6. Once the capacitor is ready, the LCD screen will display “READY”.
7. Turn off all vehicle electronics (eg, air conditioning, heating, radio, lighting, etc.).
8. Engage the vehicle’s parking brake.
9. Start the vehicle’s engine by pressing the power button on the jump starter.
10. If the LCD screen does not activate or displays an error code, refer to the troubleshooting section in the user manual.

Intended use

The product is a standalone vehicle battery jump starter. It uses a capacitor to capture and store residual energy from a weakened 12V battery, then releases that stored energy to crank start the engine. It cannot be used on a battery that has a voltage less than 6V.

• This product does not contain a rechargeable battery so does not need to be charged.
• If you use the product for purposes other than those described, the product may be dam-aged.
• Improper use can result in short circuits, fires, electric shocks or other hazards.
• The product complies with the statutory national and European requirements.
• For safety and approval purposes, you must not rebuild and/or modify the product.
• Read the operating instructions carefully and store them in a safe place. Make this product available to third parties only together with the operating instructions.
• All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery contents

• Product
• Operating instructions

Latest product information

Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Description of symbols

The following symbols are on the product/appliance or are used in the text:

• The symbol warns of hazards that can lead to personal injury.
• This product must only be used in dry, enclosed indoor areas. It must not become damp or wet.
• Read the operating instructions carefully.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

General

• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• If you have questions which remain unanswered by this information product, contact our technical support service or other technical personnel.
• Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

Handling

• Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

Operating environment

• Do not place the product under any mechanical stress.
• Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
• Protect the product from high humidity and moisture.
• Protect the product from direct sunlight.

Operation

• Consult an expert when in doubt about the operation, safety or connection of the product.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
  • is visibly damaged,
  • is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to any serious transport-related stresses.

Electrical safety

• Switch off the vehicle engine and electronics before connecting the product.
• Clean the battery terminals to maintain proper contact and prevent short circuits.
• Avoid electric shock! Do not operate the product with wet hands and check the battery clamp and cable insulation is not damaged.
• Remove metal jewelry (e.g., necklaces, rings) when working with batteries to reduce the risk of short circuits, electric shocks, or burns.

Personal safety

• Wear eye protection to prevent injuries from explosions or corrosive chemicals while working with lead-acid batteries.
• Risk of explosion! Never operate the product in areas where flammable fumes or gases are present (e.g. petrol stations).
• Risk of burns – Allow engine compartments to cool down as they can reach high temperatures.
• Keep away from moving engine parts like belts, pulleys and fans.
• Risk of entanglement and burns! Loose clothing and jewelry can get caught or entangled in moving or hot parts.
• Explosive / noxious gases may be produced / present during use. Always use the product in a well-ventilated area.
• Have someone nearby in case there is an emergency.

Lead-acid battery

• Keep fresh water, soap and eyewash within reach.
  • If battery acid contacts skin or clothes, wash immediately with soap and water.
  • Avoid touching eyes. If acid enters eyes, flush with water for 10 minutes and seek medical help immediately.

Product overview

Product

1. LCD screen
2. Power button
3. Leads

LCD status display

1. Battery voltage
2. Connected to battery
3. Battery voltage out of range:
   • LOW: <6 V, HIGH: >13 V
4. Ready for jump starting
5. Capacitor charging status

Connection

Preparation for connection
Before connecting the cables to a battery:

• Switch OFF all vehicle electrics (e.g. air conditioner, heater, radio, lights etc.).
• Make sure the ignition key is in the “OFF” position. For push-to-start ignition, make sure the vehicle is completely OFF.
• Check the battery contact terminals are clean.
• Prepare your vehicle for ignition (e.g. place gear in park and engage the emergency brake).

Connecting the leads

Important:
Always connect test leads to terminals in the correct order.

1. Connect the red clamp to the positive (+) terminal.
2. Connect the black clamp to the negative (-) terminal.
3. Wiggle the clamps back and forth to ensure proper connection.
4. The LCD should activate. If the LCD does not activate see section: Troubleshooting.

Disconnecting the leads
When finished using the product:

1. Press the button to switch the power OFF.
2. Disconnect the red clamp.
3. Disconnect the black clamp.

Operation

1. Connect the product to the vehicle battery terminals. See section: Connection.
2. Press the button to switch the power ON.
   • If everything is functioning correctly the capacitor will start charging. See section: LCD status display.
   • If there is a problem with the battery an error message will appear. See section: Troubleshooting.
3. Wait for a “beep” sound and READY to appear on the display.
   • Jump start the vehicle engine.
4. If ignition is successful, let the engine run to allow the battery to recharge, and disconnect the product from the battery. See section: Disconnecting the leads.
   • If ignition is not successful, switch the product OFF, and repeat steps 2 – 3.

Notes:

• In some cases when the ambient temperature is <0 °C, the LCD display may not activate but the product will still function.
• In such cases wait approximately 5 minutes for the audible “beep”. This indicates the capacitor has reached full charge and is ready to jump start the vehicle engine.

Troubleshooting

it should be <13.8 V.
F02| Rechargeable battery voltage is too low.| Test the rechargeable battery, it should be >6 V.
F03| Product has circuit malfunction.| Do not use the product.
F04| Rechargeable battery capacity is

<2 Ah.

| Try to recharge the battery or consult a qualified technician.
LCD does not activate| Cables not connected correctly.| Recheck the connections.
Rechargeable battery voltage is

<5.5 V.

| Try to recharge the battery or consult a qualified technician.
Weather is too cold (<0 °C).| The LCD does not activate but the ca- pacitor may still function. See section: Operation.

Cleaning and care

Important:

• Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. They damage the housing and can cause the product to malfunction.
• Do not immerse the product in water.

1. Disconnect the product from the power supply.
2. Clean the product with a dry, fibre-free cloth.

Disposal

This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life. Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):

• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

Technical data

• Input ……………………………………….. 12 V 10 A
• Output……………………………………… 12 V
• Starting current…………………………. 500 A
• Peak current …………………………….. 1000 A
• Capacitor ………………………………….
  • Charging: approx. 3 mins. (70 Ah battery)
  • Lifespan: approx. 10,000 cycles
• Reverse polarity protection…………. yes
• Short circuit protection……………….. yes
• Operating conditions………………….. -40 to +65 °C, 30 to 60 % RH (non-condensing)
• Storage conditions…………………….. -40 to +65 °C, 30 to 80 % RH (non-condensing)
• Dimensions (W x H x D) …………….. 136 x 57 x 200 mm
• Weight (approx.)……………………….. 1.00 kg

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited. This publication reflects the technical status at the time of printing.

Copyright by Conrad Electronic SE.
2799626_V1_0623_dh_mh_en 9007200127995531-2 I2/O1.

References

• Conrad Electronic » All parts of success
• Conrad Electronic » All parts of success
• Download center

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>