Yale YRD642 Assure Lock Touchscreen Deadbolt Instruction Manual

Yale YRD642 Assure Lock Touchscreen Deadbolt

This manual will walk you through all the required steps to add your new Yale Assure Lock to your door.

• Remove existing deadbolt
• Double check door measurements
• Install your Assure Lock
• Program your Assure Lock
• Add your Assure Lock to your smart home system or Yale Access app if purchased with Yale Smart Module or Yale Access Upgrade Kit

Failure to follow these instructions could result in damage to the product, voiding the factory warranty and could lead to failure of the product to provide access.

Removing Existing Deadbolt

Do not discard old lock hardware until Assure Lock has been successfully installed.

Check Door Measurements and Make Adjustments If Needed

Install Deadbolt and Strike Plate

Creating Master Entry Code

The Master Entry Code is used to change the lock settings. A security best practice is to set your Master Entry Code with 6 or more digits and create a separate code that is used daily to lock and unlock the door.

Creating Entry Codes

Master Entry Code must be created first.

• • Max Entry Codes = 250 with Smart Module; 25 without.

Setting Definitions

• *The Master Entry Code must be created prior to any other programming of the lock.

Customizing YRD642 ACC ON LY
Lock Using Settings Menu

1. Press Yale logo to wake up lock.
2. Enter Master Entry Code* followed byion.
3. Lock Response: “Welcome to the Settings Menu. Press each number to hear available settings and then press the settings icon to enter.”
4. Enter digit corresponding to the function to be performed followed by the 10: icon. Follow the voice commands.

• • Master Entry Code must be created prior to any other programming of the lock.
• **If Escape Return Mode is enabled, Auto Re-lock cannot be enabled.
• ***Configuration will disable locking/unlocking via Entry Codes.

Troubleshooting

• *When batteries are replaced, Smart Module Locks have a real time clack that will be set via the User Interface. It is recommended to verify correct date and time; particularly those locks operating under Daylight Savings Time.

Hardware Troubleshooting

• If deadbolt does not extend or retract easily when testing thump burn and keypad operation, revisit installation steps. It is important that the bolt be in the retracted position during lock installation and that installation procedure is followed carefully.
• Attempt remanding using Settings Menu.

Helpful Tip: Ensuring smooth deadbolt operation can enhance your battery life.

If deadbolt does not fully extend, consider increasing depth of deadbolt strike pocket in frame.

To adjust Knob/Lever/Handle set strike plate:

1. Remove plate from door frame with a manual screwdriver. (Using an electric driver may strip screw heads or enlarge screw holes.)

2. Locate strike plate tab Bend the tab towards surface of strike.
   Note: A small change may be all that is required
   Tab

3. Reinstall strike plate using a manual screw driver and test again.

4. If door cannot be adjusted sufficiently with strike tab, both knobbier/handle set latch and deadbolt latch could require adjustment – we suggest you contact a local locksmith for assistance.

For help with misalignments, watch our door alignment video: US.YaleHome.com/eon/support/Yale assure- lock-FAQs /electronic-lock installation/

Resetting Lock to Factory Default

When lock is reset to factory defaults all Entry Codes (including Master Entry Code*) are deleted and all programming features are reset to original default settings (see below).

1. Remove battery cover and batteries.
2. Remove inside lock to access reset button.
3. Reset button (see image at right) is located beside cable adapter.
4. While pressing reset button (minimum of 3 seconds) reinstall batteries. Release reset button.
5. Replace battery cover.

Upon reset, Master Entry Code creation is the only option available and must be performed prior to any other programming of the lock.

FCC:

FCC ID: 2ABFG-YRD642BLEV1
Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio(TV technician for help.

Waning: Changes or modifications to this device, not expressly approved by Yale Home could void the user’s authority to operate the equipment

industry C11n11da:
IC ID: 11626A-YRD642BLEV1
This Class B digital apparatus meets all requirements of the Canadian Interference

Causing Equipment Regulations.
Celt apparel pillage name pique de la classed B re pond a touts Les exigence’s de !’interference Canadienne causing des regalements’ equipment. Thi5 device complies with part 15 owl the FCC Rules. Operation is subject to the folic vying two conditions: Cl) This device may not cause harmful interference, al’\d (2) this device must accept any irater refence recede, including interference that may cause undesired operation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>