DrBrown s C1Pv1LXNggL Deluxe Baby Bottle Warmer Instruction Manual

: June 13, 2024
: DrBrown s

Table of Contents

DrBrown s C1Pv1LXNggL Deluxe Baby Bottle Warmer Instruction Manual
INSTRUCTIONS FOR USE
Package Contents:
Specifications:
IMPORTANT SAFEGUARDS
• DO NOT open Sterilizing Lid or reach over the appliance while in use,
Never freeze glass containers, as glass may break.
Before feeding, always check the content temperature of the bottle or
Do not use an extension cord.
SAVE THESE INSTRUCTIONS
PARTS OF THE INSTA-FEED™
BOTTLE WARMER: 4 6
WARMING BOTTLES AND FOOD JARS
CAUTION: Always unplug the warmer before filling.
- Do not use Sterilizing Lid for warming.
USE DISTILLED WATER ONLY!

DrBrown s C1Pv1LXNggL Deluxe Baby Bottle Warmer Instruction Manual

INSTRUCTIONS FOR USE

Package Contents:

Insta-Feed™ Bottle Warmer Quick Reference Guide2x Storage Caps

Specifications:

Nominal voltage: 120VAC/60Hz 500W

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in

damage to the product, personal property and cause serious injury. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children. Do not attempt disassembly or use with incompatible components. This manual contains instructions for safety, operation and maintenance.

IMPORTANT SAFEGUARDS

READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WHEN USING ELECTRICAL APPLIANCES, PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:

DO NOT IMMERSE IN
HOUSEHOLD USE
Do not touch hot

• DO NOT open Sterilizing Lid or reach over the appliance while in use,

as steam will cause burns and serious injuries. Do not touch lid or interior parts during use, as serious injury may occur.

Always remove the Sterilizing Lid carefully by the handle. Take care when removing the Sterilizing Lid as there may be some residual steam—keep hands and face Allow the steam to clear before reaching into the unit. Always retrieve the sterilized parts by removing the Lift-Out Basket.
To protect against electrical shock, do not immerse cord or plug in water or other
Close supervision is necessary when any appliance is used near
This appliance shall not be used by Keep the appliance and its cord out of reach of children.
Unplug from outlet when not in use and before Allow to cool before putting on or taking off parts.
Always unplug the warmer before Do not use Sterilizing Lid for warming.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any Return appliance to the nearest authorized service facility for examination, repair or adjustment.
Misuse of the product may cause potential
The heating element surface is subject to residual heat after
The use of accessory attachments not recommended by Handi-Craft Company and may cause
Do not use
Do not let cord hang over edge of table or counter or touch hot
Do not place on or near a hot gas or electric burner or in a heated oven.
Extreme caution must be used when moving an appliance containing hot
To operate, plug cord into wall To disconnect, turn any control to “off,” then remove plug from wall outlet.
Always add water and then press Power If the Power Button is pressed first, steam may form when water is added.

Never freeze glass containers, as glass may break.

Do not use this warmer for frozen milk or Always thaw frozen milk or food overnight in the refrigerator first before warming.
Do not use appliance for other than intended
Never immerse the warmer or power cord in water.
When in use, the warmer contains hot Be careful to avoid spilling or splashing any water on yourself when removing contents from the warmer.
Before serving, be sure food is at a safe
Warming food for long periods is not
Food should not be heated for too long

Before feeding, always check the content temperature of the bottle or

the small jar.

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
Before servicing, unplug cord from wall Do not leave cord within child’s reach.
The preheating of the appliance is not
A short power-supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a longer

Do not use an extension cord.

Children shall not play with the
Any maintenance servicing should be performed by an authorized service
NOT FOR SPACE HEATING

SAVE THESE INSTRUCTIONS

PARTS OF THE INSTA-FEED™

BOTTLE WARMER: 4 6

Warming Chamber
Indicator Light
Power Button 5
Sterilizing Lid 1
Adapter Ring
Measuring Cup
Lift-Out Basket 7
Storage Caps

WARMING BOTTLES AND FOOD JARS

CAUTION: Always unplug the warmer before filling.

Do not use Sterilizing Lid for warming.

Remove the Measuring Cup from the rear of the
Add DISTILLED water to the Measuring Cup, following the Warming Guide on page 5 to determine the amount of water to add based on your bottle type. Note: These amounts are a guide only. There are many

variables that can impact the final temperature of thebottle or food jar you are warming, such as starting temperature, size, and shape. Always test the temperature before feeding your baby.

USE DISTILLED WATER ONLY!

Tap water and bottled water contain minerals that shorten the life of this appliance. Damage from use of non-distilled water will void the warranty.
Pour the DISTILLED water from the Measuring Cup directly into the Warming Do not overfill, as overfilling may cause the bottle/food jar to be overheated or may cause damage to the unit.
Replace the Measuring Cup and plug in the power
Note: The first time the unit is plugged in, the warming cycle may begin automatically. If the Indicator Light is on upon plugging unit in, wait for the warming cycle to end (Indicator Light will turn off) and allow the unit to cool down for 10 minutes before using.
Place the bottle or food jar inside the Warming Chamber as outlined
Wide Neck Bottle: Place bottle directly into Warming

Narrow Bottle: Place Adapter Ring on top of Warming Chamber, then place bottle in Warming The Adapter Ring will keep your bottle centered over the heating plate for even warming.
Note: To prevent leakage when warming Dr. Brown’s® bottles, remove the internal parts, collar, and nipple/teat, and replace with the included Storage Cap.
Food Jar: Place food jar into the Lift-Out Basket, then place Lift-Out Basket in Warming
Note: Always remove the lid of the food jar prior to warming. After warming cycle is complete, be sure to stir food thoroughly until it is an even temperature throughout.

Press the Power The Indicator Light will turn on, indicating the warming cycle has begun.

CAUTION: Always add water and then press Power Button. If the Power

Button is pressed first, steam may form when water is added.
WARNING: DO NOT reach over the appliance while in use, as steam will cause burns and serious injuries. Do not touch hot surfaces during or immediately after use.
Note: If the Power Button is pressed without water added, the unit will shut off automatically after a short period. If this happens, wait at least 10 minutes to allow warmer to cool before adding water and starting warming cycle.

When the Indicator Light turns off, the warming cycle is done. Remove the bottle/food jar promptly to avoid Gently stir or swirl content to ensure it warms evenly. DO NOT shake.

Note: Always test the temperature before feeding your baby. Adjust the amount of water added to the warming chamber as needed; if the bottle/food jar is too cold, add slightly more water next time. If the bottle/food jar is too warm, use slightly less water next time.

Wait at least 10 minutes to allow warmer to cool before using

WARMING GUIDE

STERILIZING SMALL PARTS

CAUTION: Always unplug the warmer before filling.

The sterilize feature can be used for any small part safe for steam sterilization. DO NOT sterilize bottles in this sterilizer.

Add 2 oz / 60 mL of DISTILLED water directly into the Warming Do not overfill, as overfilling may cause damage to the unit.
Place small parts (nipples/teats, pacifiers/soothers, ) to be sterilized in the Lift-Out Basket.
Place the Lift-Out Basket with small parts into the Warming
Place the Adapter Ring on top of the Warming
Place the Sterilizing Lid on top of the Adapter
Plug in the power cord and press the Power The Indicator Light will turn on, indicating the sterilizing cycle has begun.

WARNING: DO NOT open Sterilizing Lid or reach over the appliance while in

use, as steam will cause burns and serious injuries. Do not touch hot surfaces during or immediately after use.

When the Indicator Light turns off, the sterilizing cycle is
Allow the unit to cool for at least 10 minutes before removing the Sterilizing Lid, Adapter Ring, and Lift-Out

CAUTION: Be sure to observe the 10-minute cooling time as warmer parts

and sterilized parts will be hot. Always remove the Sterilizing Lid
carefully by the handle. Take care when removing the Sterilizing Lid as there may be some residual steam—keep hands and face away. Allow the steam to clear before reaching into the unit. Always retrieve the sterilized parts by removing the Lift-Out Basket.

TROUBLESHOOTING TIPS

If the warmer is not operating, check that the power cable is connected to the power outlet and water has been added to warming
If Indicator Light does not come on/warming cycle does not start, warmer may be cooling Wait 10 minutes and try again.
If Indicator Light comes on upon plugging in but before Power Button is pressed, it is possible the Power Button was pressed while the warmer was Wait for the warming cycle to end (Indicator Light will turn off) and allow the unit to cool down for 10 minutes before using.
If bottle/food is too warm/too cold after warming cycle, note the Warming Guide only shows approximate amount of water Warming times are impacted by many variables, so adjust the amount of water added as needed. If the bottle/ food jar is too cold, add slightly more water next time. If the bottle/food jar is too warm, use slightly less water next time.

CLEANING THE INSTA-FEED™ BOTTLE WARMER AND PARTS

CAUTION: ALWAYS TURN OFF, UNPLUG, AND ALLOW THE UNIT TO COOL BEFORE

CLEANING.

Bottle Warmer Unit: Wipe outer surface and inside the Warming Chamber with a damp cloth or sponge using mild liquid soap. Wipe with clean water and allow unit to air dry. DO NOT SUBMERGE UNIT IN WATER.
Lift-Out Basket, Adapter Ring, Sterilizing Lid, and Measuring Cup: Dishwasher safe (top rack only) or wash with soapy water. Rinse with clean water and allow to air dry.

DE-SCALING THE INSTA-FEED™ BOTTLE WARMER

It is recommended to de-scale you Insta-Feed™ Bottle Warmer every four weeks to ensure the unit continues to work properly. To de-scale, follow the steps below.

Unplug the appliance from
Mix 2 oz / 60 mL of white vinegar with 4 oz / 120 mL of distilled DO NOT USE BLEACH.
Pour the white vinegar and water mixture directly into the Warming
Allow the mixture to stand in the unit until any mineral deposits
Discard the cleaning mixture and rinse with clean
Wipe the Warming Chamber dry with cloth or allow to air