ergotron 45-248-026 LX Dual Stacking Arm User Guide
- June 4, 2024
- ERGOTRON
Table of Contents
45-248-026 LX Dual Stacking Arm
User Guide
45-248-026 LX Dual Stacking Arm
Tools Needed
Rotate – portrait/landscape
Adjustment step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if the product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Adjustment step Lift- up and down
CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment.
|
Increase Lift Strength If the mounted weight is too heavy or this product does
not stay up when raised, then you’ll need to increase Lift Strength:| Decrease
Lift Strength If the mounted weight is too light or this product does not stay
down when lowered, then you’ll need to decrease Lift Strength:
Adjustment step
Tilt – Foward, and Backward
CAUTION: DO NOT remove the screw. Removing
screws may cause damage to equipment.
|
Increase Lift Strength If the mounted weight is too heavy or this product does
not stay up when raised, then you’ll need to increase Lift Strength:| Decrease
Lift Strength If the mounted weight is too light or this product does not stay
down when lowered, then you’ll need to decrease Lift Strength:
Adjustment step
Arm – Side to side
CAUTION: DO NOT remove the screw. Removing screws may cause damage to equipment.
|
Increase Friction If this product moves too easily, then you’ll need to
increase friction:| Decrease Friction If this product is too difficult to
move, then you’ll need to decrease friction:
Yup, that’s it. Really. Now your LX Arm is ready for however you work
best.
Learn more about ergonomic computer use at:
www.ergotron.comiergonomics
Important Information.
Safety
Warning: Because mounting surface materials can vary widely, it is
imperative that you make sure the mounting surface is strong enough to handle
mounted products and equipment.
Caution: Leave enough slack in the cable to allow a full range of motion.
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in equipment damage or personal injury.
CAUTION: For Desk Clamp installations. Do Not rotate the display past the
edge of the desk
The lowermost range of motion for vertical lift is decreased up to 4.5″ (114
mm) when the arm is adjusted to hold over 20Ibs (9 kgs). 
Can have up to 4 arms on pole.
See updated maximum weight capacities:
Maximum monitor width will decrease depending on arm configuration.
CAUTION: DO NOT EXCEED THE MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY
OR PROPERTY DAMAGE MAY OCCUR!
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will
move up rapidly, on its own, as soon as the attached equipment is removed. For
this reason, DO NOT remove equipment unless the arm has been moved to the
highest position! Failure to follow this instruction may result in serious
personal injury and/or equipment damage!
Optional Grommet Hole Mounting
CAUTION: Bolt must be centered in the hole. For secure arm attachment and
to avoid equipment damage, the plate must make contact with the underside of
the desk on both sides of the hole.
For the latest User Installation Guide please visit:
www.ergotron.com
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit:
http://contactergotron.com
NOTE: When contacting customer service, reference the serial number.
While Ergotron, Inc. makes every effort to provide accurate and complete information on the installation and use of its products, it will not be held liable for any editorial errors or omissions (including those made in the process of translation from English to another language), or for incidental, special or consequential damages of any nature resulting from furnishing this instruction and performance of equipment in connection with this instruction. Ergotron, Inc. reserves the right to make changes in the product design and/or product documentation without notification to its users. For the most current product information, or to know if this document is available in languages other than those herein, please contact Ergotron. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan, Minnesota, 55121, USA Patents Pending and Patented U.S.& Foreign. Ergotron is a registered trademark of Ergotron, Inc.
www.ergotron.com
USA: 1-800-888-8458
Europe: +31 (0)33-45 45 600
China: 400-120-3051
Japan: japansupport@ergotron.com
© 2016 Ergotron, Inc.
All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>