FIECE FM Series Minimalist Design Timepiece Watch User Manual
- August 31, 2024
- FIECE
Table of Contents
FIECE FM Series Minimalist Design Timepiece Watch
Understand More
E-mail feicewatch@hotmail.com
Shenzhen Shifenshimiao Watch Co., Ltd. Building A, Shengtao Qianhai industrel
Park, Guxing Community Xixang Steet, Baoan Dstct, Shenzhen
Water Resistance
Please note that water resistance of watch is different from that in daily concept. Water resistance shall be considered as the atmospheric pressure the watch can withstand at the same depths in water. It shall not be understood as the depth in water.
- Do not wear the watch when taking a bath or wear it under circumstances with big temperature difference as water-proof rubber will have clearance because of thermal expansion and contraction and thus water-proof performance will be affected due to accelerated aging.
- The crown shall be placed at the normal position. The spiral crown shall be locked tight and is not allowed to be adjusted in water.
- Please keep the watch away from water if the band is made of leather, or the bạnd may be damaged due to soaking by water. Be sure to pay close attention.
- In autumn, winter and rainy seasons, the sudden chilling is likely to cause a layer of mist, which is a normal physical phenomenon. It will disappear naturally when the climate is dry and it has little impact on the movement.
FM202/FM212/FM1405 Operating Instructions
Adjusting method:
When the crown is at position 0, rotate the crown clockwise to wind up the
watch, the power indicator will point to the full spring direction.
Pull the crown to position 1 to adjust the date. Pull the crown to position 2
and rotate the minute hand to adjust time.
Maintenance Guide
When you wind the spring clockwise and the hand points to the maximum energy
position 35, the fingers will feel pressure and the crown will be difficult to
rotate. In this case, the winding should be stopped. Endless winding is
strictly prohibited. The Screw-in crown of FM1405 needs to be manually locked
to achieve waterproof performance.
FM121/FM022 Operating Instructions
Adjusting Method:
Pull the crown to position 1, rotate it clockwise to adjust date and rotate
counter clock wise to adjust week day. Pull the crown to position 2 to adjust
time. Month sub-dial: Press button A to adjust month. (Date only increases)
Year sub-dial: Press button B to adjust year. (Year only increases) 24 hours
sub-dial: Automatically calibrate the three-pin-time.
Maintenance Guide
The fingers will feel pressure and the crown will be difficult to rotate when
the hand points at full energy position. In this case, the winding should be
stopped. Endless winding is strictly prohibited. Please do not wear it when
bathing, swimming or under circumstances with hot vapor.
FM201/FM301/FM508/FM221/FM221PRO/FM506 Operating Instructions
Adjusting method
Winding Up:
Rotate the crown clockwise about 20 laps to wind up the mechanism. You will
feel a bit tight when the watch is fully powered, please stop winding up at
this time to avoid damage the movement.
Date Setting: Pull out the crown to position 1 and rotate the crown
clockwise to adjust the date. When setting the date for the first time, please
set the date to the previous date, then rotate the crown until the current
date appears. Date setting is recommended while the hands indicate between
6:00-9:00 to avoid damage the movement.
Time Setting: Pull out the crown to position 2 and rotate the crown
clockwise to adjust the time.
Tips: The mainspring is wound up by the move of your arm, it is
recommended you wear the watch for more than 8 hours a day. If you do not wear
the watch for that much time, it may not be wound sufficiently. In such cases,
you can manually wind up the watch but do no wind up it endlessly.
FS303/FS306/FS302 Operating Instructions
Adjusting Method:
- Pull the crown to position 1 and rotate counterclockwise to adjust date and pull it to position 2 to adjust time.
- 60 minute chronograph dial: Press button A to start timing and press button A to stop.
- Press button B to reset. 24 hour dial: Automatically calibrate the three-pin-time.
- Second hand has mechanical scanning function, it only moves when timing.
Note: It is normal that the second hand does not move. It will not affect the watch’s time. Maintenance Guide: Please do not place the watch near amplifier, stereo, TV, magnets to avoid the movement being magnetized. Please do not wear it when bathing, swimming or under circumstances with hot vapor.
FM602/FM603/FM606/FM666 Operating Instructions
Adjusting method:
Position 0: Normal Position
Position 1: Time Setting When pushed into the case, the crown ensures
that the watch is water resistant.
Winding Up: When the crown is in position 0, rotate the crown clockwise
to wind the watch.
Time Setting: Pull out the crown to position 1 and rotate the crown to
adjust the time.
Maintenance Guide: The mainspring is wound up by the move of your arm, it
is recommended you wear the watch for more than 8 hours a day. If you do not
wear the watch for that much time, it may not be wound sufficiently. In such
cases, you can rotate the crown clockwise to wind the watch. When the movement
is fully wound, your fingers will feel pressure and the crown will be
difficult to rotate. At this time, the winding should be stopped. Endless
winding is strictly prohibited.
FM019/FM019 HOT Operation Instructions
Adjusting method:
The Screw-in crown has 2 positions:
Position 0: Normal Position
Position 1: Time Setting When pushed into the case, the crown ensures
that the watch is water resistant.
Winding Up: Rotate the crown counterclockwise to unlock it, then rotate
the crown clockwise about 30 laps to manually wind up the watch. Push it back
into position 0 and rotate it clockwise to lock it tightly after finishing
winding up. Time Setting: Rotate the crown counterclockwise to unlock it, pull
out the crown to position 1, and rotate the crown clockwise to adjust the
time. Push it back into position 0 and rotate it clockwise to lock it tightly
after finishing adjusting.
Tips: The mainspring is wound up by the move of your arm, it is recommended you wear the watch for more than 8 hours a day. If you do not wear the watch for that much time, it may not be wound sufficiently. In such cases, you can manually wind up the watch but do no wind up it endlessly. Fm019 with calendar
FK030 Operation Instructions
These two crowns are used to adjust the 12 hours dial and 24 hours dial
On/Off the Stopwatch
Standard time display, press button “B” to enter Stopwatch mode Press button
“D” to start or pause;Press button “C” to clear records;Press button “B” to
return to standard time display
Alarm Setting
Standard time display, press button “B” twice. Press button “D” to adjust
hours, Press button “C” to switch to set minutes, “D” to adjust minutes, “B”
to return to standard time display.
Time Setting on Digital Sub-Dial( Time, Calendar and Weekday)
Standard time display, press button “B” 3 times, second value will flicker.
Press button “C” to switch in sequence: seconds, minutes, hours, day, month
and weekday, “D” to adjust, “B” to return to standard time display. Turn off
Hourly Chime and Sound Reminders: Standard time display, press the B (the
button on the left under the case) and the C (the button on the right below
the case) at the same time. When you press it, if there is a week, it
indicates that the reminder is turned on, otherwise it indicates it is turned
FK036 Operation Instructions
Time Setting on Digital Sub-Dial( Time, Calendar)
Standard time display. Press button “B” for 2 seconds. Press button “C” to
increase, “D” to decrease. Press button “B” to switch in sequence: Seconds,
minutes, hours, 12 or 24 hours system, month, day, year, Exit in one minute
without operation
Alarm Setting
Standard time display, press button “B”. On/Off Alarm, Press button “C” to
select, “B” to confirm. AL for alarm clock display, “CH” for hourly time. (AL
is on the upper left of the weekday sub-dial in the top of the ease. Pess
uton” to adjust the in to eliust to confirm and exition “C” to increase, “D”
to decrease. Press button “B” to adjust the minute, “B” to confirm and exit.
On/Off Timer
Standard time display, press “B” key 3 times to enter countdown (“TM” on):
press “C” key to start or pause, press “D” key to clear records.
On/Off the Stopwatch
Standard time display, press button “B” twice to enter stopwatch(“ST” on):
Press button “C” to start or pause, “D” to clear records.
FK814 Operation Instructions
Time Setting on Digital Sub-Dial Time, Calendar and Weekday)
Sequence: Sec did, mires, nor fin, a wee. Way, ext the Soups Are achius:
Pars ben me hour vich in Mashes press displayed, it dicate the 12 hour tomar
format.
On/Off the Stopwatch
Standard time display, press button “A”. Press button “B” to start or pause.
Press button “B” for 4 seconds to clear records
Alarm Setting
Stands, Pries display press button in quimes: Press, Minute, Alarm conds to ad
tHe, Ex the suryal A to When setting Alarm and Hourly Chime, press button “A”
to set in sequence: Turn on Alarm, Turn on Hourly Chime, Turn on Alarm and
Hourly Chime, Turn off Alarm and Hourly Chime. “B” to exit the setup
Dual Time Setting
Standard time display, press button “A” 3 times. Press button “B” for 4
seconds to adjust. When the hour value flashes, Press button “B” to switch in
sequence: Hours, Minutes, Exit the setup. “A” to adjust value.
On/Off Timer
Standard time display, press button “A” 4 times. Press button “B” for 4
seconds to adiust. When the hour value flashes, Press button “B” to switch in
sequence: Hours, Minutes, Exit the setup. Press button “A” to adjust value,
After setting the timing time, “B” to start or pause the timing.
FK817 Operation Instructions
Time Setting on Digital Sub-Dial Time, Calendar and Weekday)
Standard time display, press button “D” for 2 seconds. When the seconds are
flashing, Press button “B” to switch in sequence: seconds, minutes, hours,
12/24 hour format, month, day, year. Press button “C” to adjust value, “D” to
exit the setup. in sequence: hours, minutes. Press button “C” to adjust value,
“D” to exit the setup
Alarm Setting sequence:
Tu on Alan, Tum on Hourly Chime, Tum On Alam Ho Hour Chime, Tum off Alarm and
Hourty Chime. Press button “D” for 2 seconds to adjust Alarm. When the hour
value flashes, Press button “B” to switch in sequence: hours, minutes. Press
button “C” to adjust value, “D” to exit the setup
On/Off the Stopwatch
Standard time display, press button “B” 2 times to enter Stopwatch mode.
Press button “C” to start or pause;Press button “D” to clear records
On/Off Timer
Standard time display, press button “B” 3 times. When the seconds is in pause
state, Press button “D” for 2 seconds to adjust. When the hour value flashes,
Press button “B” ‘to switch in sequence: Hours, Minutes. Press button “C” to
adjust value, “D” to exit the setup. After setting the timing time, press
button “C” to start or pause the timing. When the seconds is in pause state,
press button “D” to return the seconds value to zero.
Dual Time Setting
Standard time display, press button “C”. Press button “D” for 2 seconds to
adjust. Press button “B” to switch in sequence: Minutes, Hours. Press button
“C” to adjust value, “D” to exit the setup.
FK220/FK037/FK052/FK055/FK026/FK131/FK812 Operating Instructions
Time Setting
Pull out the crown to position and rotate the crown clockwise to adjust the
date; Pull out the crown to position 2 and rotate the crown clockwise to
adjust the time. The 24-hour sub-dial will automatically synchronize the time
of the main dial.
Chronograph Function
Press Button A to start/Stop counting.When the timing is paused, press button
B to reset value to zero,restore the original state.
Note The stopwatch counts each revolution-circle,the chronograph minute hand beats a small division
FK038 Operating Instructions
Time Setting
- Press button B three times to enter time setting mode, second value will flicker.
- Press button C to adjust the time.
- Press button D to switch to second-minute hour→date month→weekly calendar setting in turns.
- Press button B to return to standard time display
Note: Press button C to check the date, A or P is shown in 12 hour format when in setting mode.
Stopwatch Mode
- Press Button B once to enter into stopwatch mode, 0:00 will appear on the lower time sub-dial.
- Press button C to start/stop counting and press button D to reset value to zero. Alarm Setting 1.Press button B twice to enter into alarm mode and value will flicker on the digital sub-dial. 2.Press button D to adjust hour.
- Press button C to switch to minute setting, then press button D to adjust minute.
- Press button B to return to standard time display.
Turn off Hourly Chime and Sound Reminders: Standard time display, press and hold button D and then press button B to display all weekday. it indicates that the reminder is turned on, otherwise it indicates it is turned off.
FM023 Operating Instructions
Winding Up: Rotate the crown counterclockwise to unlock it, then rotate
the crown clockwise about 30 laps to manually wind up the watch. Push it back
into position 0 and rotate it clockwise to lock it tightly after finishing
winding up.
Date Setting: Rotate the crown counterclockwise to unlock it, pull out
the crown to position 1, and rotate the crown clockwise to adjust the date.
Push it back into position 0 and rotate it clockwise to lock it tightly after
finishing adjusting.
Time Setting : Rotate the crown counterclockwise to unlock it, pull out
the crown to position 2, and rotate the crown clockwise to adjust the time.
Push it back into position 0 and rotate it clockwise to lock it tightly after
finishing adjusting.
Weekday Sub-Dial (Button A): Rotate button A counterclockwise to unlock
it, then press button A to adjust the month. Rotate button A clockwise to lock
it tightly after adjusting the weekday.
Note: Press the button twice to add a day. (Weekday only increases)
Month Sub-dial (Button B): Rotate button B counterclockwise to unlock it,
then press button B to adjust the month. Rotate button B clockwise to lock it
tightly after adjusting the month. Note: Press the button twice to add a
month. (Month only increases)
24 Hour Sub-dial: The sub-dial automatically calibrates in line with the
main dial.