BOYO VT-BP3 360 Degrees Birdview Rear Camera Owner’s Manual
- June 5, 2024
- BOYO
Table of Contents
BOYO VT-BP3 360 Degrees Birdview Rear Camera
Product Introduction
4D panoramic reversing assist system, through a single large wideview angle camera mounted behind the car, Collect images from the rear of the vehicle during the reversing and perform image distortion correction through “Image Distortion Restoration and Docking Technology” -> Perspective-> image stitching .. > image enhancement and other processing, and finally form a 4D panorama. ~ference information through real car model, the driver can easily identify the vehicle position, obstacle distance, surrounding environment and other factors to achieve fast and Safe reversing BEFORE using this reversing system, please read the safety information provided in this user manual. ALWAYS use the product as outlined in this user manual.
Product Accessories
Please check all the components listed below are in the kit
Product Accessories
- Reserved
- Menu
- Exit
- Left
- UP
- 0K
- Right
- Down
Installation
installation Position
Reversing camera suggested position: Above edge of the car license plate, make
sure that the camera is not in the way of the key switch of the truck.
Attentions
- Install the camera in a position where there is no object blocking the front view. Secure it to avoid any vibration.
- Choose flat ground with good light as an alignment site to place the calibration cloth. Specification:size 14.4ft3.9ft black and white squares size 7.8in7.8in edge 3.9in
- Put the calibration cloth on the back of the car, Calibrate the centerline of the cloth to align the vertical centerline of the car, the left and right sides are parallel to the rear wheel. (refer to picture below)
- Put the edge of calibration cloth parallel to the edge of car trail, and keep 5.9 inch distance (as below picture), make sure the camera can observe the edge of the car calibration cloth
Software adjustment
Enter calibration settings
First entry: When the software interface is not displayed, you can enter the
software calibration interface setting by long pressing the remote control to
set the red button.
Camera calibration
After the calibration cloth is placed as shown above, when the video on the
right side of the screen is almost the same as the effect image, the edge of
the black and white grid of the calibration cloth corresponds to the
disappearing position, click the software to start the calibration button.
After the · calibration has startedr the software performs the calibration
function, and the video interface displays the calibration, then wait for the
calibration to be completed.
Calibration status:
Calibration successful: When the interface prompts calibration is complete, go
to the next calibration setting via the remote control.
Calibration failed: When the ·interface prompts that the calibration fails,
please adjust the calibration cloth according to the corresponding position
and click again to start calibration. Reason for failure:
Reason for failure –
- flute floor is not flat enough and no enough light
- There is an item above the black and white grid of the calibration cloth to block the identification of the calibration cloth.
- The black and white grid of the calibration cloth is not clear enough with many folds.
The following figure is the effect of the camera-centered installation. When
not centered, the effect is slightly different and is not affected. 
image offset calibration
When the camera position is not centered, the calibration cloth position needs
to be adjusted in the actual video screen on the right. Adjust the position of
the calibration cloth in the video by the up, down, left and right buttons, to
adjust the position of the calibration cloth in the centre of the video image.
Car parameters calibration
Please modify the following car properties according to the actual model and
parameters.
- Body width range 55~ 98 in
- Car default 67in
- SUV default 70.9in
- Other default 82. ?in
- Body length range is 126.0~216.5in
- Car default 189.0in
- SUV default 196.9in
- Other default 196.9in
Image parameter calibration
The camera screen can adjust the brightness, contrast, and saturation range
from 0 to 100. Default 50 Please adjust the corresponding parameters according
to the actual screen effect (the default effect of the parameters is the best,
non-image color sensitive people, it is recommended to use the default value)
Video cropping
This page is cropped by the marker line and finally displays the image size
behind the reversing interface. The remote control selects the marking line
(blue effect) by up, down, left and right. When you need to adjust a certain
marking line, click the OK button (the marking line is red effect), then move
to the ideal position, and click the OK button again to exit the adjustment.
Parameter saving
When all parameters have been calibrated. Preview the actual effect of the
video screen and confirm that the parameters on the right side are correct and
save the parameters. When an error occurs, click the Cancel button to
recalibrate Software settings menu description Standby time: refers to the
non-reversing gear position, and after the specified time, the panoramic
reversing system will exit. System type: CVBS output type, default N system
Panorama position: the position of the reversing panorama can be switched, the
default left
1 YEAR LIMITED WARRANTY
This limited warranty is given to the end-user or the retail purchaser (referred to this warranty as “Original Purchaser” ) that it will be free from defects in material and workmanship for a period of one year from the date of the purchase of the new product (excluding accessory items such as power cords, cradle, memory card, adaptor and cables). A copy of the original proof of purchase and this warranty card with RMA number given by Vision Tech America, Inc. is required to receivewarranty service. In the unlikely event that the new product should fail due to defect in material or workmanship, Vision Tech America, Inc. will repair or replacewith a new or refurbished product, where each party Will be responsible for one-way shipping for the lower 48 states customers only. ers residing in Hawai i, Alaska, and Puerto Rico, the customer is responsible for freight charges incurred both ways.
This limited warranty does not cover any physical damage to this product, damage caused by improper installation; improper use; misuse; neglect; repair of cracked, scratched, broken, or modified cosmetics; or parts that have been altered or removed; damages done by another device used with this product resulting from use of non BOYO®- brand parts. This warranty is VOID if you purchased this product as used, floor model sample, or refurbished; if the product has been altered or modified in any way (including but not limited to attempted repair without authorization from BOYO®- Vision TechAmerica, Inc. and/or alteration/removal of the serial number ). This limited warranty does not cover the vehicle of any damages or liabilities in which this product is installed or is being installed. does not guarantee avoidance of vehicle collision or accident.
If you are having trouble with the product, please contact our technical
support at 888-941-3069 or email:
info@visiontechamerica.com with your
questions or comments. If your product is eligible to receive a warranty,
request for warranty service online by visiting
http://visiontechamerica.com/site/get-warranty/
This warranty is invalid if
the factory-applied serial number has been altered or removed from the
Product.
IMPORTANT: TO SEND DEFECTIVE PRODUCTS FOR WARRANTY SERVICE, (RETURN MATERIAL
AUTHORIZATION) AND INCLUDE ORIGINAL PROOF OF PURCHASE AND THIS WARRANTY CARD
WITH THE SHIPMENT.
VISION TECH AMERICA CUSTOMER SERVICE CENTER
888-941-3969 or visit
www.visiontechamerica.com
For an accessory or part not available from your authorized dealer, call
For U.S. 888-941-3069 International
714-446-9543
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>