AMP 77133-01A Jeep Wrangler JL 2Dr Installation Guide
- June 13, 2024
- AMP
Table of Contents
APPLICATION
Jeep Wrangler JL 2Dr
2018 – 2022
AMP Part #
77133-01A
77133-01A Jeep Wrangler JL 2Dr
INSTALLATION TIME
3-5 Hours
Professional installation recommended
SKILL LEVEL
1 2 3 4
4= Experienced
TOOLS REQUIRED
- Safety goggles
- Measuring tape
- 10 mm socket
- 13 mm socket
- 1/2” socket
- Ratchet wrench and extension
- Wire crimpers
- Wire stripper / cutter
- 3/16” hex key wrench (allen wrench)
- 4mm hex key wrench ( allen wrench )
- Electrical tape
- Weather proof caulking (silicone sealer)
- Silicone spray
- Drill
- Drill bit 3/16”
WARRANTY
5-Year Limited Warranty
AMP RESEARCH TECH SUPPORT
1-888-983-2204 (Press 2) Monday –
Friday, 7:00 AM – 5:00 PM PST
Invented, engineered and manufactured exclusively by AMP Research in the USA.
May be covered by one OR MORE of the following patents:
6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,413,204;
7,398,985; 7,584,975; 7,566,064; 7,487,986; 8,157,277; 8,408,571; 9,302,626;
9,561,751; 10,053,017; CA2463717 ©2012 AMP Research. All rights reserved.
Printed in USA.
EXPLODED VIEW
- Motor
- Hex Head Bolt
CAUTION: HANDLE WITH CARE.
To ensure our customers receive all components with full integrity, we pack
the motors separate from their linkage assemblies.
This requires that the installer position and fasten the motor before
continuing with the install.
Please follow the instructions below and handle the assembly carefully.
CAUTION: Dropping the assembly or any excessive impact MAY cause damage
to the motor. Instructions:
- Position the gear cover in place as shown if not already in place.
- Seat motor into position on the three mounting bosses. This may require an adjustment of the gear by moving the swing arms.
- After seating into place, fasten the motor with the three motor mount screws with 4mm Hex Head. lighten screws to 36 in-lbs (4N-m). Do not over torque.
Front bracket Assembly : Use Driver side front bracket (34). Remove
factory fender bolt using a 10mm socket or wrench. Next set bracket into
position slide bracket over existing rivet nut on pinch weld. Insert provided
M6 Flange bolt (13) and tighten to 8 ft- lbs. Use provided spacer (22) and M6
Nylock nut (23) assemble over rivet nut and finger tighten. Use provided M8
Conical washer bolt (17) and finger tighten. Tighten M6 nut and M8 Conical
washer bolt simultaniously. Torque nut to 8 ft-lbs and conical washer bolt to
16 ft-lbs. Assemble Flange Bolt (14) with nut (18) and torque to 16 ft-lbs.
Rear bracket Assembly: Use Driver side rear bracket (36). Use provided
button head bolt(12) and washer(20) with captive washer nut(19) on pinch weld.
Assemble hardware loosely. Next use provided captive washer bolt (17) to
attach bracket to underside of body. Torque to 16 ft-lbs. Assemble Flange
Bolt (14) with nut (18) and torque to 16 ft-lbs.
Slide 6 carriage bolts (16) into rail pocket of driver side rail. Add Light Bracket (8) to the 1st and 4th bolt counting from the front side. Insert Flange Nut (18) onto bracket tab to attach light brackets into position shown. Leave loose to allow for adjustment.
Adjust bolts and slide over brackets. Use supplied flange nuts and attach rail to brackets.
Center rail between body rocker and torque 4 flange nuts to 16 ft-lbs. Assemble Flange bolt (14) with nut (18) thru support tab on bracket. Torque to 16ft-lbs.
Mount front Idler linkage onto driver side. Thread supplied bolts (17) into linkage. Repeat step for Rear Drive linkage. Do not tighten.
Install provided spacer (21) and M6 bolt (13) into upper mount as shown on
both the drive and idler linkages. Do not tighten.
Slide mounting T-nut into position. Center board in rail pocket. Tighten
fasteners to 10 ft-lb
Using a 13mm socket Torque linkage bolts 4x (17) from step 3 to 16 ft-lbs. Next, use a 10mm socket, torque linkage spacer bolt 2x (13) from step 6 to 8 ft-lbs. Once linkages are tight cycle board to verify steps deploy under own weight.
Attach motor (29) to linkage. Using a 13mm wrench Torque to 36 in-Lbs.
Remove fuse from Power Step Wire Harness.
Prepare large tie-wraps for mounting Power Step Controller. Loosely loop tie-
wraps around large bundle of wires behind battery in engine compartment.
Insert controller into tie-wrap loops and cinch down securely.
The tie-wraps should cinch down into channels on controller surface. Connect
power leads from Controller, Red to positive battery terminal and Black to the
vehicle body ground as shown.
Route the two Wire Harness legs down over the wheel wells toward Motor Linkages, long leg across to the driver side. Secure harness with tie wraps.
Press and release glove box safety tab to fully open and remove glove box, next, release glox box dampener located on the left side.
Carefully leave glove box hanging to expose plugs behind it.
Locate white block (on right side) and plug the 2 pin connector from the OBD module extension (9) into that port.
Pull back carpet on passenger side on the top side of middle console and then use provided Tube (10) to route OBD II Extension (9) behind middle console. Tape open end of extension to the tube and push the tube through middle console.
From driver side, pull tube (10) that was pushed through from passenger side.
Remove OBD II Extension (9) from tube (10) and plug wire (9) to OBD module (8)
wire.
Route trigger wires through firewall. Locate round plastic plug on firewall to
the left of the brake assembly. Drill small hole using a 3/16 drill bit. Route
trigger wires (6) through firewall. Use supplied posi-lock® (11) to connect
wires to OBD Module (8).
Apply silicone to seal off firewall.
Use cable ties to secure all wires in place. Plug in OBD Module.
OBD II install: Use Supplied Posi-Lock® connectors to attach the Plug and
Play Module to the Harness. Attach matching colors on the harness to the wires
on the module. Plug in module to OBD II port on the vehicle. Secure harness
with supplied tie wraps.
Note: If the OBD II pass thru harness (76404-01A) was purchased see
install sheet supplied in packaging. The pass through harness allows for an
open port for other accessories. See below for a brief description.
On driver side, run Wire Harness leg down and along underside of the vehicle floor and frame to front Drive Linkage. Connect harness to motor and secure harness with tie wraps. Route remainder of wire harness towards rear linkage assembly for LED lights. Repeat step on passenger side.
Affix LED lamp (27) to Light bracket (28) on rail. Slide bracket into desired position and tighten using 5/32” Allen key.
Using supplied butt connectors (26), connect the lamp wires. Red to Red, Black to Black. Once Crimped use heat gun to shrink tube. Close and wrap conduit with electrical tape. Secure all loose wires with cable ties. Pull lamp wires upward to avoid any wire snagging.
Reinstall Fuse from Powerstep Wire Harness.
Check that all doors activate the Power Step and the LED Lights work when
doors open and close. Reinstall any remaining trim panels.
FINAL SYSTEM CHECK
Check that all doors activate the PowerStep and the LED lights work when doors
open and close.
NORMAL OPERATION: When the doors open, PowerStep automatically deploys from
under the vehicle.
When the doors are closed, PowerStep will automatically return to the
stowed/retracted position. Note that there is a 2-second delay before the
PowerStep returns to the stowed/retracted position.
CORRECT OPERATION OF LIGHTS: All four lamps will illuminate upon opening any
door of vehicle.
Lamps will stay on until restowing of both Power Steps or until 5 minutes has
expired with the doors open.
When the lights timeout after 5 minutes, they can be reillumintated by closing
and opening any door of vehicle.
AMERICAN DESIGNED, ENGINEERED AND MANUFACTURED.
Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR FASTER SERVICE & PRODUCT UPDATES
Please visit: www.amp-research.com/productregistration or scan the QR Code
http://www.amp-research.com/productregistration
Product Registration Benefits:
- Ensure we have your purchase receipt and product info in our system which is required for warranty
- Faster and easier access to customer service and tech support in the unlikely event you need warranty or product support
- Registration helps us keep you up to date on product information and offers
To view other Amp Research products that may be offered for your vehicle.
Please visit: www.amp-research.com
Congratulations on your purchase of the genuine AMP Research PowerStep!
Here’s what you should know…
POWER-DEPLOYABLE RUNNING BOARD OPERATION: AMP Research PowerStep running boards automatically move when the doors are opened to assist entering and exiting the vehicle.
Automatic power deploy:
The running boards will extend down and out when the doors are opened.
Automatic power stow:
The running boards will return to the stowed position when the doors are
closed. There will be a 2-second delay before the running boards move to the
stowed position.
Automatic stop:
If an object is in the way of the moving running board, the running board will
automatically stop.
To reset, clear any obstruction, then simply open and close the door to resume
normal operation.
Manually set in the deployed (OUT) position for access to the roof:
The running boards can be manually st in the deployed position by firmly
holding the step down with your foot while at the same time closing the door.
To resume normal operation, open and close the door.
Maintenance: In adverse conditions, debris such as mud, dirt, and salt may
become trapped in the running board mechanism, possibly leading to unwanted
noise. If this occurs, manually set the running boards to the deployed
position and flush the front and rear hings arms with a high pressure car
wash wand.
Avoid spraying the motors directly. After washing, apply silicone spray
lubricant to the hinge pivot pins.
Do not apply silicone, wax or protectants like Armor All® to the running board
stepping surface.
Caution! Keep hands away when the running board is in motion.
5-YEAR LIMITED WARRANTY
AMP RESEARCH warrants this product to be free from defects in material and
workmanship for FIVE (5) YEARS FROM DATE OF PURCHASE, provided there has been
normal use and proper maintenance. This warranty applies to the original
purchaser only. All remedies under this warranty are limited to the repair
replacement of the product itself, or the repair or replacement of any
component part thereof, found by the factory to be defective within the time
period specified. The decision to repair or replace is wholly within the
discretion of the manufacturer.
for instructions. You must retain proof of purchase and submit a copy with any
items returned for warranty work. Upon completion of warranty work, if any, we
will return the repaired or replaced item or items to you freight prepaid.
Damage to our products caused by accidents, fire, vandalism, negligence,
misinstallation, misuse, Acts of God, or by defective parts not manufactured
by us, is not covered under this warranty.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE
AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or
the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from
state to state.
FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH TECH SUPPORT
1-888-983-2204
WARNING
Be sure to read and precisely follow the provided instructions when installing
this product. Failure to do so could place the vehicle occupants in a
potentially dangerous situation. After installing or reinstalling, re-check to
insure that the product is properly installed.
The material that your product is made from can be recycled.
Please also consider recycling the packaging that your product came in.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>