HUBBARDTON FORGE 363015 Tura Outdoor Pendant Instruction Manual
- June 13, 2024
- HUBBARDTON FORGE
Table of Contents
HUBBARDTON FORGE 363015 Tura Outdoor Pendant
ASSEMBLY & INSTALLATION INSTRUCTIONS
Component Parts
- Fixture
- Fixture Coupling
- Canopy
- Crossbar
- Ground Screw
- Threaded Stud (2)
- Knurled Ball (2)
- 3″ Fixture Pipe (1)
- 6″ Fixture Pipe (1)
- 12″ Fixture Pipe (2)
- Double Pipe Coupling (3)
- Socket
- Glass
- Retaining Ring
- Retaining Ring Tool
- White Washer
- Bulb (Not Included)
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS
PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a
licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction
and operation of the product and the hazards involved.*
Caution: Do not exceed the maximum wattage noted on the fixture. Use only
recommended bulbs with fixtures Please Note: After installation extra hardware
and accessories are possible due to our kits being used on multiple products
and options
To Install the Fixture (Figure 1 – on the following page)
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION
-
Carefully unpack the fixture from the carton.
-
Feed supply wires through the centre of the crossbar (D) with ground screw (E) facing down. Using two machine screws (not provided), fasten the crossbar (D) to the electric box.
Note : A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with the new fixture -
Thread studs (F) through appropriate holes in the crossbar (D) to match holes in the canopy (C).
-
Locate fixture pipes (H, I, J), fixture (A) and couplings (K ). Couplings can be found in the kit bag
-
Provided are multiple fixture pipes in three different lengths. Choose the combination that will achieve the overall height desired. Refer to the table below to determine the pipes required to reach the desired overall height. Once you
have determined the components necessary, feed the wires that exit the fixture coupling (B) through the individual components. Wires will slip easier through loose components than through pipes and couplings that are pre-assembled. -
Apply a drop of the supplied thread-locking compound to the internal threads of fixture coupling (B) and pipe couplings (K). Thread pipes (H, I & J) and pipe couplings (K) together: Application of the thread locking compound is necessary to prevent the stem from loosening during regular maintenance and cleaning of the fixture. Be certain to apply the compound
-
Thread pipe assembly onto the fixture coupling (B).
-
Feed wires through the canopy (C).
-
Thread canopy (C) onto fixture pipe assembly.
-
Raise the fixture close to the ceiling.
-
Refer to the instructions on the next page to continue the installation. Using suitable wire connectors (not provided) connect fixture wires to supply (white to white and black to black). Attach a pigtail lead to the crossbar ground screw (E). Connect all ground wires (bare copper or green to bare copper or green).
CAUTION : MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS EXPOSED -
Slide canopy (C) over threaded studs (F) and push firmly to the ceiling, making sure that no wires are pinched between canopy (C) and ceiling. Fasten with knurled balls (G). Be sure studs (F) are fully seated in the knurled balls (G).
-
Follow the steps on the next page to complete the installation.
To Install Glass (Figure 3)
-
The retaining ring (N) is shipped and installed. Remove and retain for the next steps.
-
Carefully unpack glass (M).
-
Slide glass (M) over a socket (L) followed by a white washer (P) and, using a tool (O) provided, secure both with a retaining ring (N).
Note : Be sure not to over-tighten as this could break the glass (M). -
Install bulb (Q), not included, into a socket (L).
-
Restore electricity at the main breaker
If you need further assistance or find that you are missing any parts, please
contact the dealer from which you purchased this product. We hope you enjoy
your fixture! Hubbardton Forge will not be liable for injury or damage caused
by improper installation, lamping or use of this fixture MODERN AMERICAN
BLACKSMITHS | FINE, HANDCRAFTED LIGHTING
CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>