HUBBARDTON FORGE 131525 Echo Linear Pendant Instruction Manual

HUBBARDTON FORGE 131525 Echo Linear Pendant

Product Information

The Echo Linear Pendant 131525 is a lighting fixture that comes with various component parts including a fixture, canopies, screws, anchors, swivels, standoffs, knobs, pipes, safety cables, nuts, washers, sockets, bulbs, glass, retaining rings, and a retaining ring tool. The fixture is designed to be installed in a room’s ceiling and is meant to provide ambient lighting.

Product Usage Instructions

Before installing the Echo Linear Pendant 131525, ensure that the power is off at the main breaker box. Follow the steps below for installation:

To Install a Canopy (Figure 1)

1. Carefully unpack the canopy (B).
2. Place the canopy (B) over the electrical box and line up the holes in the canopy with the holes in the electrical box. With a pencil, mark the location of mounting holes needing anchors in canopy on ceiling. Set canopy (B) aside.
3. Drill 1/4 holes in the locations marked on the ceiling. Place the tapered end of the anchors (E) into the holes and gently tap them flush to the ceiling using a lightweight hammer.
4. Thread the wires in the electrical box through the hole in the canopy (B) while moving the canopy into position. Using two machine screws not provided, fasten canopy (B) to the electric box.
5. Install screws (D) into holes with anchors (E). Be sure not to overtighten and strip the anchor (E).

To Assemble and Install Fixture (Figure 2)

1. Carefully unpack fixture (A) from the carton.
2. Locate fixture pipes (I, J, K), fixture (A), stem nipples (L).
3. Choose the combination of fixture pipes that will achieve the overall height desired. Refer to the table provided in the instructions to determine the pipes required to reach the desired overall height.
4. Once you have determined the necessary components, feed wires that exit fixture (A) through individual components. Wires will slip easier through loose components than through pipes and nipples that are pre-assembled.
5. Once wires are run, apply thread locking compound to all connection points and assemble the pipes and nipples to achieve the configuration shown in Figure 2.
6. Attach the glass (R) by placing it into the retaining ring (S) and securing it in place with the retaining ring tool (T). Repeat for all 12 glass pieces.
7. Attach the socket (P) to each pipe.
8. Lift fixture assembly (A) up to canopy (B) and place safety cables (M) loops over hooks in canopy (B).
9. Using suitable wire connectors (not provided), connect fixture wires to supply (white/ribbed to white and black/smooth to black). Connect all ground wires (bare copper or green to bare copper or green).
10. Align the holes in canopy plate (C) with standoffs (G) and secure with knobs (H). Be sure no wires are pinched between the canopy (B) and the canopy plate (C).

Component Parts

• A Fixture
• B Canopy
• C Canopy Plate
• D #10 Screws (8)
• E Anchors (8)
• F Swivel (2)
• G Standoffs (4)
• H Knob (4)
• I 3″ Fixture Pipe (2)
• J 6″ Fixture Pipe (2)
• K 12″ Fixture Pipe (6)
• L Stem Nipples (10)
• M Safety Cable (2)
• N Nut (2)
• O Washer (2)
• P Socket (12)
• Q Bulb (12 – Not Included)
• R Glass (12)
• S Retaining Ring (12)
• T Retaining Ring Tool

ASSEMBLY & INSTALLATION INSTRUCTIONS

CAUTION : FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
Caution: Do not exceed the maximum wattage noted on the fixture. Use only recommended bulbs with fixtures.
Please Note : After installation extra hardware and accessories are possible due to our kits being used on multiple products and options.

To Install a Canopy (Figure 1)

CAUTION : BE SURE THE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.

1. Carefully unpack canopy (B).

2. Place canopy (B) over the electrical box. Line up holes in the canopy with holes in the electrical box. With a pencil, mark the location of mounting holes needing anchors in the canopy on the ceiling. Set canopy (B) aside.

3. Drill 1/4″ holes in the locations marked on the ceiling. Place the tapered end of the anchors (E) into the holes and gently tap them flush to the ceiling using a lightweight hammer.

4. Thread the wires in the electrical box through the hole in the canopy (B) while moving the canopy into position. Using two machine screws (not provided) fasten canopy (B) to the electric box.
   NOTE : A NEW ELECTRIC BOX COMES WITH SCREWS. WHEN REPLACING A FIXTURE, RETAIN THE EXISTING SCREWS FOR USE WITH THE NEW FIXTURE.

5. Install screws (D) into holes with anchors (E). Be sure not to overtighten and strip the anchor (E).

6. Follow the instructions on the following page to assemble and install the fixture.

To Assemble and Install the Fixture (Figure 2) on the following page

1. Carefully unpack fixture (A) from the carton.

2. Locate fixture pipes (I, J, K), fixture (A), and stem nipples (L) . Stem nipples (L) can be found in the kit bag.

3. Provided are multiple fixture pipes in three different lengths. Choose the combination that will achieve the overall height desired. Refer to the table below to determine the pipes required to reach desired overall height. Once you have determined the components necessary, feed wires that exit fixture (A) through individual components. Wires will slip easier through loose components than through pipes and nipples that are pre-assembled. Once wires are run, apply thread locking compound to all the connection points and assemble the pipes and nipples.
   NOTE : THE APPLICATION OF THE THREAD-LOCKING COMPOUND IS NECESSARY TO PREVENT THE PIPE FROM LOOSENING DURING REGULAR MAINTENANCE AND CLEANING OF THE FIXTURE. BE CERTAIN TO APPLY THE COMPOUND.

4. Slip wires from the fixture (A) through assembled swivel (F) and thread the swivel into the fixture pipe.

5. Repeat steps 3 & 4 for the second set of pipes.

6. Ensure that slots on swivels (F) are aligned as shown in Figure 2.

7. Carefully place canopy plate (C) over swivels (F) and secure with washers (O), safety cables (M) and nuts (N) as shown in Figure 2. Washers (O), safety cables (M) and nuts (N) can be found in the kit bag.

8. Lift fixture assembly (A) up to canopy (B) and place safety cables (M) loops over hooks in the canopy (B).

9. Using suitable wire connectors (not provided) connect fixture wires to the supply (white/ribbed to white and black/smooth to black). Connect all ground wires (bare copper or green to bare copper or green).
   CAUTION : MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS EXPOSED.

10. Align the holes in the canopy plate (C) with standoffs (G) and secure them with knobs (H).
    CAUTION : BE SURE NO WIRES ARE PINCHED BETWEEN CANOPY (B) AND THE CANOPY PLATE (C).

11. Refer to the instructions on last page to install glass.

To Install Glass (Figure 3)

1. Remove the retaining ring (S) from the socket (P). Retaining rings are shipped and installed.
2. Install bulb (Q) – not included.
3. Slip glass (R) over a socket (P) until it rests on checking.
4. Using provided retaining ring tool (T), thread the retaining ring (S) onto socket (P) until snug against the glass (R). Do not over-tighten as this could break glass (R).
5. Repeat for remaining bulbs (Q) and glass (R).
6. Restore electricity at main breaker.

If you need further assistance or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>