HUBBARDTON FORGE 134502 Summit Pendant Instruction Manual
- October 30, 2023
- HUBBARDTON FORGE
Table of Contents
HUBBARDTON FORGE 134502 Summit Pendant Instruction Manual
Component Parts
- A Fixture
- B Crossbar
- C Jam Nut
- D Threaded Nipple
- E Ground Screw
- F Canopy Ring
- G Canopy
- H Swivel
- I 3″ Fixture Pipe (1)
- J 6″ Fixture Pipe (1)
- K 12″ Fixture Pipe (2)
- L Stem Nipple (5)
- M Socket
- N Bulb (not included)
- O Glass
- P Retaining Ring
- Q Shade
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS
PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a
licensed electrician. This product must be installed in accordance with
applicable installation code(s), by a person familiar with the construction
and operation of the product and the hazards involved.* Caution: Do not exceed
maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: After installation extra hardware and accessories are possible
due to our kits are used on multiple products and options.
To Install Fixture (Figure 1) on following page
CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.
-
Carefully unpack fixture (A) from the carton.
-
Thread jam nut (C) and crossbar (B) onto threaded nipple (D) with ground screw (E) facing towards swivel (HI); leave both parts loose.
-
Using two machine screws (not provided), temporarily fasten crossbar (B) to the electric box.
NOTE: A NEW ELECTRIC BOX COMES WITH SCREWS. WHEN REPLACING A FIXTURE, RETAIN THE EXISTING SCREWS FOR USE WITH THE NEW FIXTURE. -
Adjust the length of threaded nipple (D) in crossbar (B) so that canopy ring (F) will hold canopy (G) against the ceiling with no threads showing for best appearance. When the correct adjustment is established, tighten jam nut (C) against crossbar (B) to secure the adjustment.
-
Remove crossbar (B) from the electrical box and proceed with the assembly instructions.
-
Locate fixture pipes (I, J, K), fixture (A), stem nipples (L) . Stem nipples (L) can be found in the kit bag.
-
Provided are multiple fixture pipes in three different lengths. Choose the combination that will achieve the overall height desired. Refer to the table below to determine the pipes required to reach the desired overall height. Once you have determined the components necessary, feed the wires that exit fixture (A) through the individual components and thread pipes and nipples together. Wires will slip easier through loose components than through pipes and nipples that are pre-assembled. Once wires are run, apply thread locking compound to all the connection points and assemble the pipes and nipples.
NOTE: APPLICATION OF THE THREAD LOCKING COMPOUND IS NECESSARY TO PREVENT THE PIPE FROM LOOSENING DURING REGULAR MAINTENANCE AND CLEANING OF THE FIXTURE. BE CERTAIN TO APPLY THE COMPOUND. -
Carefully slide canopy ring (F) and canopy (G) over wires and fixture pipes (I, J, K) until they rest on fixture (A).
-
Slip wires from the fixture (A) through assembled swivel (H) and threaded nipple (D).
-
Refer to instructions on next page to continue installation.
-
Using two machine screws (not provided), fasten crossbar (B) to the electric box.
-
Using suitable wire connectors (not provided) connect fixture wires to supply (white/ribbed to white and black/smooth to black). Attach a pigtail lead to crossbar ground screw (E). Hold canopy (G) close, connect all ground wires (bare copper or green to bare copper or green).
CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS EXPOSED. -
Slide canopy (G) against ceiling, and secure with canopy ring (F).
CAUTION: BE SURE NO WIRES ARE PINCHED BETWEEN CANOPY (H) AND THE CEILING. -
Locate shade (Q). Slip shade (Q) over socket (M) and press up tight to fixture arms.
-
Secure shade (Q) using retaining ring (P).
-
Install bulb (N) (not included) into socket (M).
-
Refer to instructions on next page to install glass.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture! * Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
To Install Glass (Figure 2)
- Carefully unpack glass (O) and place over frame (P).
- Carefully lift frame (P) and glass (O) up to fixture ensuring that socket (M) passes through the center of the glass and secure with binding screw (R) and binding nut (Q) to fixture (A). R
- Install bulb (N) (not included) into socket (M).
- Restore electricity at main breaker.
MODERN AMERICAN BLACKSMITHS | FINE, HAND CRAFTED LIGHTING CASTLETON, VERMONT USA | HUBBARDTONFORGE.COM