KENDAL LIGHTING MSA19-BLK Magna Slim Trac Magnetic Lighting System Installation Guide

KENDAL LIGHTING MSA19-BLK Magna Slim Trac Magnetic Lighting System

For mounting to ceiling utilizing CABLE SUPPORTS for both Single and Multiple tracks.

CAUTION:

1. BEFORE INSTALLING THE LIGHT FIXTURES, PLEASE READ THE INSTALLATION INSTRUCTIONS CAREFULLY.
2. DISCONNECT POWER AT THE CIRCUIT BREAKER BEFORE INSTALLATION OR SERVICING.
3. DO NOT INSTALL THE TRACK IN DAMP OR WET LOCATIONS.
4. THIS TRACK IS IP20, INDOOR USE ONLY.
5. ALL ELECTRICAL CONNECTIONS SHOULD BE DONE BY A QUALIFIED ELECTRICIAN

NOTE:

1. TRACK SECTIONS SHOULD BE JOINED TOGETHER ON THE FLOOR BEFORE INSTALLING INTO THE CEILING.
2. WHEN INSTALLING LONGER TRACK RUNS UTILIZING MULTIPLE SECTIONS, THE ELECTRICAL CONNECTION BETWEEN EACH SECTION IS TERMINATED. A NEW CONNECTION FROM THE DRIVER SHOULD BE MADE AT THE START OF EACH ADDITIONAL 96-WATT SECTION WITHOUT THE USE OF MSA22 4-PIN CONNECTORS OR RECESSED CABLE CONNECTORS.

ACCESSORIES REQUIRED

INSTALLATION

STEP 1 DETERMINE THE LOCATION ON THE CEILING ABOVE WHERE THE TRACK IS TO BE INSTALLED

STEP 2 ADJUST THE POWER CABLE LENGTH AND ATTACH THE MSA18 POWER SUPPLY/SUPPORT TO THE JUNCTION BOX

STEP 3 DETERMINE THE POSITION AND INSTALL CABLE SUPPORTS (MSA19) TO THE CEILING

STEP 4 USING PROVIDED ALLEN WRENCH, LOOSEN SET SCREWS ON THE POWER LOCATION ACCESS COVERS. SLIDE THE COVERS OPEN TO ACCESS THE 24-VOLT POWER CONNECTION.

STEP 5 CONNECTS 24-VOLT POWER FROM THE DRIVER TO THE 24-VOLT INPUT ON THE TRACK, RED WIRE TO POSITIVE AND BLACK WIRE TO NEGATIVE. ATTACH THE WIRE RESTRAINT TO THE POWER CORD. (NOTE-IF USING A LIVE END FEEDINPUT CONNECTOR INSTEAD OF POWERING DIRECTLY TO TRACK, SEE LIVE END FEEO INSTRUCTIONS FOR POWERING)

STEP 6 SLIDE CDVERS BACK DYER ACCESS HDLEAND TIGHTEN SETSCREWS

STEP 7 INSTALL SUSPENSION CABLES TO TRACK, SEE STEP 8 AND 9

STEP 8 INSERT SET SCREWS BUT DO NOT TIGHTEN

STEP 9 TURN THE CABLE CONNECTOR COUNTER-CLOCKWISE SO THE CORNERS OF THE CONNECTOR FIT UNDER THE TOP EDGES OF THE TRACK AND TIGHTEN THE SET SCREWS

STEP 9 TURN THE CABLE CONNECTOR COUNTER-CLOCKWISE SO THE CORNERS OF THE CONNECTOR FIT UNDER THE TOP EDGES OF THE TRACK AND TIGHTEN SET SCREWS

STEP 11 INSTALL THE WIRE CLIP

STEP 12 FINISH INSTALLATION OF THE TRACK

ACCESSORIES REQUIRED:

INSTALLATION
STEP 1 DETERMINE THE LOCATION ON THE CEILING ABOVE WHERE THE TRACK IS TO BE INSTALLED

STEP 2 ADJUST THE POWER CABLE LENGTH AND ATTACH THE MSA1 B POWER SUPPLY/SUPPORT TO THE JUNCTION BOX

STEP 3 DETERMINE THE POSITION AND INSTALL CABLE SUPPORTS (MSA19) TO THE CEILING

STEP 4 REMOVE END CAPS WHERE TRACK IS BEING JOINED

STEP 5 REMOVE THE DECORATIVE PLATE FROM THE TRACK BEING ADDED

STEP 6 REMOVE THE MAGNET FROM THE TRACK BEING ADDED

STEP 7 INSTALL A POWER PLATE MSA01

STEP 8 INSTALL A TRACK CONNECTOR MSA02 TO THE END OF THE TRACK BY INSERTING IT INTO THE SLOT ON THE BACK OF THE TRACK. SLIDE THE CONNECTOR IN ALL THE WAY SO THE PINS ARE VISIBLE WHEN JOINING THE TRACKS TOGETHER.

STEP 9 WHILE CAREFULLY LINING UP THE PIN CONNECTORS WITH PIN CONNECTOR HOLES ON THE OTHER TRACK JOIN THE TRACKS TOGETHER.

ATTENTION:
WHEN JOINING TRACKS OR ACCESSORIES UTILIZING PIN CONNECTORS, MAKE SURE PINS ARE HORIZONTAL AND LINE UP WITH PIN CONNECTOR HOLES. YOU MAY NEED TO GENTLY PUSH UP OR DOWN ON THE PINS SO THEY LINE UP CORRECTLY. FAILING TO DO THIS MAY RESULT IN PINS MISSING THE PIN CONNECTOR HOLES AND LOSS OF THE 24-VOLT CONNECTION.

STEP 10 SLIDE THE MSA02 TRACK CONNECTOR BACK SO IT IS HALFWAY ONTO EACH TRACK AND TIGHTEN SET SCREWS

STEP 11 USING PROVIDED ALLEN WRENCH, LOOSEN SET SCREWS ON THE POWER LOCATION ACCESS COVERS. SLIDE THE COVERS OPEN TO ACCESS THE 24-VOLT POWER CONNECTION.

STEP 12 CONNECTS 24-VOLT POWER FROM THE DRIVER TO THE 24-VOLT ON THE TRACK, RED WIRE TO POSITIVE AND BLACK WIRE TO NEGATIVE. ATTACH THE WIRE RESTRAINT TO THE POWER CORD.

STEP 13 SLIDE COVERS BACK.OVER ACCESS HOLE AND TIGHTEN SETSCREWS

STEP 14 INSTALL SUSPENSION CABLES TO TRACK, SEE STEP 8 AND 8

STEP 15 INSERT SET SCREWS BUT DO NOT TIGHTEN

STEP 16 TURN THE CABLE CONNECTOR COUNTER-CLOCKWISE SO THE CORNERS OF THE CONNECTOR FIT UNDER THE TOP EDGES OF THE TRACK AND TIGHTEN SET SCREWS

STEP 17 ADJUST THE SUSPENSION CABLE TO THE DESIRED HEIGHT BY PUSHING DOWN ON THE CABLE GRIPPER AND PULLING THE EXCESS CABLE. ONCE HEIGHT IS FINAL, CUT OFF EXCESS CABLE.

STEP 18 INSTALL THE WIRE CLIP

STEP 19 FINISH INSTALLATION OF THE TRACK

NOTE:
AFTER EACH TRACK CONNECTION A CONTINUITY TEST SHOULD BE DONE TO ENSURE PROPER ELECTRICAL CONNECTIONS WERE MADE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>