Keyless Entry 9902 Electronic Keypad Handle with Deadbolt Instruction Manual
- May 15, 2024
- Keyless Entry
Table of Contents
Keyless Entry 9902 Electronic Keypad Handle with Deadbolt
Specifications:
- Applicable door thickness: 35-45mm
- Exterior Lock Dimensions: 1-3/4”(45mm) – 2-3/4”(70 mm)
- Interior Lock Dimensions: 1-3/8”(35mm) – 2-3/8”(60 mm)
Product Usage Instructions:
Installation Instruction:
Tools required for installation:
- Measuring Tape
- Electric Drill
- 2Hole Boring Saw
- Phillips Screwdriver
- 1 Drill Bit
Parts in the Box:
- Exterior Panel
- Interior Door Lever
- Thumb Knob
- Dead Bolt
- Striking Plate A (for Dead Bolt)
- Striking Plate B (for Latch Bolt)
- Striking Plate Box A (for Dead Bolt)
- Striking Plate Box B (for Latch Bolt)
- Latch Bolt Fixing Ring
Drill Holes:
If pre-drilled door or replacement, skip to adjusting the Dead Bolt.
Adjust the Dead Bolt:
- Pull back the block to extend the tongue.
- Rotate down.
- Pull the block back to retract the tongue.
Install the Latches and Striking Plates:
Follow instructions to install Striking Plates and Latches.
Install Exterior Lock:
Fold the template at the dotted line and tape it to the interior side of
the door at 36 to 38-inch Height. Then follow instructions for drilling holes
and installing the lock.
Install Interior Lock:
- Secure the thumb knob with Screw B ensuring the stem is vertical.
- Secure the door lever with Screw C.
- Secure the gasket with Screw C.
Fix the connecting column in the screw hole at the bottom of the panel, install the fixing ring, and insert the stem into the dead bolt and spindle into the latch bolt ensuring the dead bolt tongue is retracted.
FAQ:
-
Q: What tools are required for installation?
A: Measuring Tape, Electric Drill, 2Hole Boring Saw, Phillips Screwdriver, and 1 Drill Bit are required for installation. -
Q: What is the applicable door thickness for this product?
A: The applicable door thickness is between 35mm to 45mm.
Tools required for installation
Parts in the box
Drill Holes （For pre-drilled door, or replacement, please skip to Adjust the Dead Bolt)
Note: Applicable door thickness: 35-45mm
Fold the template at the dotted line and tape the template to the interior
side of the door at 36 to 38 inch Height.
- Mark the 2⅜ ” or 2¾”(60 or 70mm) hole center as A1 for the backset.
- Mark a point as A2, 5½” above A1 .
- Mark a point as C, about 9” below A1.
- Measure the thickness of the door and mark the middle point of the door thickness as B1.
- Mark a point as B2, 5½” above B1.
Note: Make sure the A1 and B1(A2 and B2) are at the same height.
-
Drill two Dia. 2⅛” holes for the lock bodies at point A1 and A2.
-
Drill two Dia. 1” holes for the latches at point B1 and B2.
-
Drill a Dia. 3/8” hole for the connecting column at point C.
-
Insert the latches into the holes and mark the outline of faceplates.
-
Chisel 1/8” deep holes.
-
a. Close the door with the latch installed and mark lines on the jamb as picture shown left
-
b. Align the striking plates with the lines. Draw the shape of striking plates.
- c. Drill 1” deep hole in the middle of the striking plates.
- d. Chisel 1/16” deep for the striking plates.
Adjust the Dead Bolt
The latch is initially set for 2⅜”(60mm). Switch to 2¾”(70mm), if your backset
is 70mm.
Install the Latches and Striking Plates
Install Exterior Lock
- a. Fix the connecting column in the screw hole at the bottom of the panel. The middle screw hole is recommended.
- b. Install the fixing ring.
- c. Insert the stem into the dead bolt and insert the spindle into the latch bolt.
Ensure the dead bolt tongue is retracted.
Install Interior Lock
- a. Secure the thumb knob with Screw B. Ensure the stem is vertical.
- b. Secure the door lever with Screw C.
- c. Secure the gasket with Screw C.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>