JLT CAI-F150EB-15 Cold Air Intake Kit Instruction Manual
- June 13, 2024
- JLT
Table of Contents
PERFORMANCE™
757-225-1940
WWW.JLTtruecoldair.com
Installation Instructions JLT Cold Air Intake Kit #CAI-F150EB-15
2015-2020 F-150
Raptor 3.5L & 2.7L EcoBoost
CAI-F150EB-15 Cold Air Intake Kit
Thank you for purchasing our product. We hope you are satisfied with the look
and performance.
Take your time and it will be a smooth install.
Please review complete instructions prior to installing.
-
Step#
See our website for video install instructions
Verify you have all the following parts included in the kit:
(1) JLT Intake Tube, (1) 3.5”-3″ Reducer, (1) 4.5”-4″ Reducer, (1) 22.5° 4.5”-4” Reducer, (1) AFE PCVinsert tube (2) 56 size Clamps (1) 64 size Clamp, (1) 72 size Clamp (1) 5×7″ Air Filter (1) Heat Shield (1) Heat Shield Gasket, (1) Foam Insert, (1) alcohol wipe and (1) 4” section of double-sided tape -
Gather the following tools needed for the installation: 5/16 nut driver, flat screw driver, and pliers
-
Remove the stock airbox by loosening the clamps at both turbo inlets, unplug the IAT sensor, pull down the 2 retaining clips, and remove the entire intake tube assembly.
-
Remove the adhesive backing of the heat shield gasket and apply it to the lower portion of the factory heat shield.
-
Install the JLT heat shield onto the factory box, it will slide into the back portion. Reattach the 2 clips to secure the heat shield.
-
Swap inlet air temp sensor from stock intake tube to the JLT. Twist and pull from stock tube and use light oil to insert into the grommet in the JLT tube. 2.7L and 2015-2016 3.5L owners use the grommet closest to the filter. USE SUPPLIED PLUG TO
SEAL GROMMET NOT USED.
-
Attach the air filter and reducers to the JLT intake tube, lower into heat shield and onto the turbo inlet tubes.
-
2.7L AND 2015-2016 3.5 OWNERS USE 22° REDUCER.
2017-2020 3.5L OWNERS USE THE STRAIGHT REDUCER.
-
AFE PCV INSERT:
MUST BE USED TO PREVENT CHECK ENGINE LIGHT.
Locate PCV connection at driver side turbo inlet, it’s running from the driver side valve cover.
Pull back on grey tab to release fitting, fitting maybe tight to remove but it will come off.
Insert AFE PCV insert into tube, the slash cut should be facing the turbo. Push the fitting all the way flush with connection.
Reattach PCV line.
Oil Filter: The frequency you should clean your filter will depend on
your driving conditions. It is recommended to check your filter at every oil
change or 3,000 miles. If there is a build up of dirt as thick as the wire
mesh, then it’s time to clean your filter. As irt
builds up on your filter, the restriction of the airflow also increases. More
frequent cleanings will improve your fuel economy and your vehicle’s
performance.
To properly clean your oil filter, we recommend the S&B Precision Cleaning &
Oiling Kit (located in the Parts Sold Separately Section of our website,
www.JLTtruecoldair.com).
Thanks for the business. If you have any questions, please e-mail
info@JLTtruecoldair.com or call
757-335-1940. Our hours are Monday-
Friday. 8:00am – 5:00pm Eastern Time.
JLT Performance Lifetime Satisfaction Guarantee. We want you to be a JLT
Performance customer for life! Your new JLT Performance product is warranted
to be free from defects in materials and workmanship for the life of the
original retail purchaser, subject to the limitations contained in our
warranty found here.
www.jlttruecoldair.com/warranty
We guarantee workmanship, tunability and even a pathway to discounted upgrades
for substantially improved items.
Return Policy: All returns will be subject to a 10%-25% restocking fee.
Air Filters will not be accepted for return unless they are in original
plastic
sealed bag. Please visit
www.JLTtruecoldair.com for complete return
policy.
Disclaimer: JLT Performance Inc. makes no warranties whatsoever,
expressed or implied, oral or written to any purchasers, except the warranty
above. JLT Performance Inc. hereby specifically excludes from any implied
warranty of merchantability or implied warranty of incidental, secondary, or
consequential damages of any kind whatsoever. All purchasers and users of
products manufactured by JLT Performance Inc. agree to hold harmless and
indemnify JLT Performance Inc. from any and all claims arising from their use.
Failure to receive notice of any or the limitations contained in this
disclaimer shall not serve to extend liability to JLT Performance Inc. for any
claims arising out of use of its products.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>