JLT PERFORMANCE CAI-SRTJ-12 Cold Air Intake Instruction Manual
- June 13, 2024
- JLT PERFORMANCE
Table of Contents
JLT PERFORMANCE CAI-SRTJ-12 Cold Air Intake
Product Information
- Product Name: JLT Cold Air Intake
- Compatible Vehicle: 2012-2021 Jeep Grand Cherokee 6.4L/392 SRT
- Model Number: CAI-SRTJ-12
- Manufacturer: JLT Performance
- Warranty: Lifetime Satisfaction Guarantee
- CARB E.O. No.: D-761-5
- Website: www.jlttruecoldair.com/warranty
Product Usage Instructions
- Review the complete instructions prior to installing.
- Remove the shield under the stock box as shown.
- Remove the block off plate as shown in the next pictures.
- Remove the IAT sensor from the stock tube and install it into the grommet in the JLT tube.
- Remove the 13mm bolt in the driver side apron panel.
- Lower the heat shield into the area and secure it with the supplied push pins in the front scoop first. Then use the supplied 13mm stainless bolt to secure it to the side. Push in the weather strip push pin into the shield.
- Lower the air filter down into the airbox first. With the silicone reducer on the tube and clamps loose, connect the tube and air filter. Then slide it onto the throttle body. Adjust the filter and tube position for the best fit and tighten all clamps. You may need to rotate the throttle body coupler for best fitment.
- Plug in the IAT sensor and PCV connection.
- Place the supplied CARB E.O. sticker under the hood in a visible location.
Note: For any questions or concerns, please contact the manufacturer’s customer support before seeking information online. For warranty details and additional information, please visit the official website mentioned above.
Thank you for purchasing our product. We hope you are satisfied with the look and performance. If you have any questions, please feel free to call us first before going to the internet. Take your time and it will be a smooth install.
Installation Instructions
Please review complete instructions prior to installing.
Step #|
---|---
1| Verify you have all of the following
parts included in the kit:
(1) JLT Plastic Intake Pipe with PCV fitting and IAT grommet, (1) 4″-3.5″ Silicone Elbow,
(1) 5”x7” Air Filter, (1) JLT Heat Shield, (1) 64 Clamp, (1) 56 Clamp, (1) Bolt, (2) Push Pins
2| Gather all of the following tools needed for the installation:
5/16 Nut Driver, Flat screwdriver, 13mm Socket, 10mm Socket and Ratchet
3| Remove the stock intake from the throttle body to the airbox.
Loosen clamp at the throttle body, unplug IAT sensor and PCV line, PULL UP on airbox and remove from the car.
Also, remove the shield under the stock box as shown and block off plate shown in next pictures:
|
---|---
4| Remove the IAT sensor from the stock tube and install into the
grommet in the JLT tube.
5|
Remove the 13mm bolt in the driver side apron panel
---|---
6| 
Lower heat shield into the area, secure the shield with the supplied push pins in the front scoop FIRST then use the supplied 13mm stainless bolt to secure to the side. Push in weather strip push pin into shield.
7| Lower air filter down into the airbox first, then with the silicone reducer on the tube with clamps loose, connect the tube and air filter then slide onto throttle body.
Adjust the filter and tube position for best fit and tighten all clamps. You may need to rotate throttle body coupler for best fitment.
8| Plug in IAT sensor and PCV connection.
9| CARB E.O. No. D-761-5
Place the supplied CARB E.O. sticker under the hood in a visible location.
Oil Filter
Guarantee
The frequency you should clean your filter will depend on your driving conditions. It is recommended to check your filter at every oil change or 3,000 miles. If there is a buildup of dirt as thick as the wire mesh, then it’s time to clean your filter. To properly clean your oil filter, we recommend the S&B Precision Cleaning & Oiling Kit (located in the Parts Sold Separately Section of our website, www.JLTtruecoldair.com).
Thanks for the business. If you have any questions, please e-mail info@JLTtruecoldair.com or call 757-335-1940. Our hours are Monday- Friday. 8:00am – 5:00pm Eastern Time.
JLT Performance Lifetime Satisfaction Guarantee. We want you to be a JLT Performance customer for life! Your new JLT Performance product is warranted to be free from defects in materials and workmanship for the life of the original retail purchaser, subject to the limitations contained in our warranty found here. www.jlttruecoldair.com/warranty. We guarantee the workmanship, tunability and even a pathway to discounted upgrades for substantially improved items.
Return Policy: All returns will be subject to a 10%-25% restocking fee. Air Filters will not be accepted for return unless they are in original plastic sealed bag. Please visit www.JLTtruecoldair.com for complete return policy.
Disclaimer: JLT Performance Inc. makes no warranties whatsoever, expressed or implied, oral or written to any purchasers, except the warranty above. JLT Performance Inc. hereby specifically excludes from any implied warranty of merchantability or implied warranty of incidental, secondary, or consequential damages of any kind whatsoever. All purchasers and users of products manufactured by JLT Performance Inc. agree to hold harmless and indemnify JLT Performance Inc. from any and all claims arising from their use. Failure to receive notice of any or the limitations contained in this disclaimer shall not serve to extend liability to JLT Performance Inc. for any claims arising out of use of its products.
Contact
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>