JLT PERFORMANCE CAI-TH-18 Cold Air Intake Instruction Manual
- June 13, 2024
- JLT PERFORMANCE
Table of Contents
Installation Instructions – JLT Cold Air Intake
2018-2021 Jeep Grand Cherokee Track hawk 6.2L #CAI-TH-18
CAI-TH-18 Cold Air Intake
**HIGHLY RECOMMENDED! * To view install video: go to our website, www.JLTtruecoldair.com and type CAI-TH-18 in the search box. Click on product, scroll down and click on videos. **HIGHLY RECOMMENDED! *
Thank you for purchasing our product. We hope you are satisfied with the look
and performance. If you have any questions, please feel free to call us first
before going to the internet. Take your time and it will be a smooth install.
Please review complete instructions prior to installing.
-
Verify you have all of the following parts included in the kit:
(1) JLT Plastic Intake tube, (1) 4.5″-4″ Silicone Elbow, (1) 5”x7” Air Filter, (1) JLT Heat Shield, (1) 64
Clamp, (1) 72 Clamp, (1) IAT Gasket, (1) IAT Adaptor, (4) M4-.7×10 MAF Screws, (1) Bolt, (2) Push Pins
FOR USE IN 2019-2021 MODELS ONLY: (1) PCV Bracket, (3) 8/32 x5/8 Bracket Screws (3) 8/32 Nuts (1) Hose with fitting installed -
Gather all of the following tools needed for the installation:
13mm & 10mm Sockets, Ratchet, 11/32 wrench, 5/16 Nut Driver, Flat screwdriver or pry tool, Phillips screwdriver, utility knife, light oil -
Loosen clamp at the throttle body, unplug IAT sensor, PCV Solenoid plug and PCV line, PULL UP on airbox and remove from the vehicle. Also remove the trim piece in front of the air box, it’s secured by 2 push pins on the bottom and the single weather strip push pin.
Also, remove the shield under the stock box as shown there maybe one pin to remove on side:
-
Remove the IAT sensor (twist lock) from the stock inlet tube and PCV fitting(2018 only). Use the JLT supplied gasket, screws and IAT sensor pad to assemble the JLT tube.
-
Remove the 13mm bolt in the driver side apron panel.
-
Lower heat shield into the area, secure the shield with the supplied push pins in the front scoop FIRST then use the supplied 13mm stainless bolt to secure to the side. Push in weather strip push pin into shield.
-
Lower air filter down into the airbox first, then with the silicone reducer on the tube with clamps loose, connect the tube and air filter then slide onto throttle body.
Adjust the filter and tube position for best fit and tighten all clamps. You may need to rotate throttle body coupler for best fitment.
Plug in IAT sensor and PCV connection. TIP: (2018) The PCV line twists at both ends. Twist and connect to the PCV connection on the tube. -
CARB E.O. No. D-761-5
Place the supplied CARB EO sticker under the hood in a visible location.
Oil Filter: The frequency you should clean your filter will depend on your
driving conditions. It is recommended to check your filter at every oil change
or 3,000 miles. If there is a buildup of dirt as thick as the wire mesh, then
it’s time to clean your filter.
To properly clean your oil filter, we recommend the S&B Precision Cleaning &
Oiling Kit (located in the Parts Sold Separately Section of our website,
www.JLTtruecoldair.com).
Thank you for your business. If you have any questions, please e-mail
info@JLTtruecoldair.com or call
757-335-1940. Our hours are Monday-
Friday. 8:00am – 5:00pm Eastern Time.
JLT Performance Lifetime Satisfaction Guarantee. We want you to be a JLT
Performance customer for life! Your new JLT Performance product is warranted
to be free from defects in materials and workmanship for the life of the
original retail
purchaser, subject to the limitations contained in our warranty found here.
www.jlttruecoldair.com/warranty
We guarantee workmanship, tunability and even a pathway to discounted upgrades
for substantially improved items.
Return Policy: All returns will be subject to a 10%-25% restocking fee.
Air Filters will not be accepted for return unless they are in original
plastic sealed bag. Please visit www.JLTtruecoldair.com for complete return
policy.
Disclaimer : JLT Performance Inc. makes no warranties whatsoever,
expressed or implied, oral or written to any purchasers, except the warranty
above. JLT Performance Inc. hereby specifically excludes from any implied
warranty of merchantability or implied warranty of incidental, secondary, or
consequential damages of any kind whatsoever. All purchasers and users of
products manufactured by JLT Performance Inc. agree to hold harmless and
indemnify JLT Performance Inc. from any and all claims arising from their use.
Failure to receive notice of any or the limitations contained in this
disclaimer shall not serve to extend liability to JLT Performance Inc. for any
claims arising out of use of its products.
2019-2021 model year Track hawk PCV Addendum
-
Unplug the PCV fitting and electrical connection in the airbox before removing from vehicle.
-
Using a utility knife, side cutters or drill, remove the tips of the welded rivets and remove the PCV solenoid.
-
Use the supplied hardware and bracket to mount the solenoid to the bracket as shown.
-
Slide the brown O ring up and out of the channel it’s sitting in and use oil or any lubricant to install the supplied ¾” PCV hose on to the fitting on the bottom of the solenoid.
-
Use the front strut towner nut to mount the PCV assembly to the vehicle as shown.
-
Plug in PCV and electrical connection at the solenoid.
-
Use a lubricant(light oil) on the rubber grommet in the tube and connect the 90° fitting from the solenoid connection in the tube.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>