EGR FIT-FF1000 Front Bolt On Look Fender Flares Instruction Manual

June 13, 2024
EGR

Installation Instructions
Front Bolt-On Look Fender Flares
Ford F150 (21-On)

FIT-FF1000 Front Bolt On Look Fender Flares

EGR FIT-FF1000 Front Bolt On Look Fender Flares FIT-FF1000

Important: Please read instructions entirely before installing this product.

Hardware Included QTY
Extrusion  29 ft
Alcohol wipe 4
Hardware Included QTY
--- ---
Retaining Clip 4
“U” Style clip 8
Bolt Kit Included (Bolt-On look flare only) QTY
--- ---
Extruded Plastic Nuts 42

Ensure that both left and right hand front Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come in contact with the vehicle. NOTE: Before fitting Fender Flares remove any moldings, strips or existing flares from the wheel arch. If there is a body side molding, mark where the molding is to be cut, alternatively the Fender Flare can be cut to go around the molding. Be sure to allow enough room for the extrusion. No drilling of vehicle is required for Bolt-On Look Fender Flares. This is a non- drill product. For rugged and OEM style Fender Flares start at STEP 2.
*PRIOR TO ANY PAINTING & INSTALLATION, PRODUCT SHOULD BE THOROUGHLY INSPECTED FOR ALL COMPONENTS LISTED ABOVE. PRODUCT SHOULD ALSO BE TEST FITTED PRIOR TO ANY PAINTING & INSTALLATION. PLEASE CONTACT EGR IF YOU HAVE ANY FITMENT QUESTIONS AND OR MISSING COMPONENTS.
PAINTING INSTRUCTIONS – If Fender Flares are being painted; do not install edge extrusion until painting is complete. Prior to painting, clean all surfaces to be painted using clean water and a mild detergent, do not use lacquer thinner or any solvent based products. Wipe completely dry. Best results will be achieved by wiping the areas to be painted with a tack rag just prior to painting. Most automotive paints can be applied directly to the Fender Flares, however some may require a primer (check paint manufacturer specifications). Good adhesion will be achieved without sanding. Select a paint (and primer if necessary) that is suitable for rigid plastics PMMA (Acrylic). If using a paint system that requires baking, do not expose the product to temperatures above 70°C (158°F). Do not fit the extrusion or any of the hardware to the Fender Flares until the paint is completely dry. EGR
FIT-FF1000 Front Bolt On Look Fender Flares - Step 1 STEP 1 : Attach the extruded plastic bolts. Peel back white tape liner from the bottom side of the extruded plastic bolt and press until it snaps into place. Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a dry clean cloth.EGR FIT-FF1000 Front Bolt On Look Fender Flares -
Step 2 STEP 2: Attach the included rubber seal to the Fender Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Ensure pressure is used to secure rubber seal to Fender Flare edge. Attach rubber seal along the top leading edge of the Fender Flare where it will make contact with the vehicle body.    EGR FIT-FF1000 Front
Bolt On Look Fender Flares - Step 2 STEP 3: Pulling at right angles to the extrusion, remove the liner from the extrusion in small portions and apply thumb pressure to ensure that it adheres to the Fender Flares. EGR FIT-FF1000 Front Bolt On Look
Fender Flares - Step 4STEP 4: Trim any unnecessary extrusion and discard. EGR FIT-FF1000 Front Bolt On Look Fender
Flares - Step 5

STEP 5: Clean the body areas where the Fender Flares will make contact with a clean cloth. EGR FIT-FF1000 Front Bolt On Look Fender Flares - Step
6

STEP 5: Clean the body areas where the Fender Flares will make contact with a clean cloth.
For models equipped with factory fender flares, removal of factory flares are required, please consult the vehicle service manual for factory fender flare removal.EGR FIT-FF1000 Front Bolt On Look Fender Flares -
Step7 STEP 7: Remove six 7mm bolt, retain for installation of Fender Flares.EGR FIT-FF1000 Front Bolt On Look Fender
Flares - Step 8 STEP 8: Place the Fender Flare onto the vehicle and fit into the correct position following the contours of the body. Use 2 of the retaining clips and 7.0mm bolts to secure the Fender Flare to the body. Make sure the clip securely engages the Fender Flare.
NOTE: If part fits loosely, add more tension by sliding clip upwards before tightening bolt.EGR FIT-FF1000 Front Bolt On Look Fender Flares -
Step 9 STEP 9: Reinstall the remaining 7mm bolts, two at the front bottom corner and two at the rear bottom corner.EGR
FIT-FF1000 Front Bolt On Look Fender Flares - Step 10 STEP 10 : Repeat installation method for other side. Double check the front Fender Flares to make sure all bolts are tight and clips are securely fastened. Your installation is now complete. Do not use abrasive cleaners.

REAR FENDER FLARE INSTALLATION

EGR FIT-FF1000 Front Bolt On Look Fender Flares - Step
11

STEP 11: Clean the body areas where the Fender Flares will make contact with a clean cloth.
For models equipped with factory fender flares, removal of factory flares is required, please consult the vehicle service manual for factory fender flare removal.EGR FIT-FF1000 Front Bolt On Look Fender Flares - Step
12 STEP 12 : Remove the two 7mm factory wheel well spat bolts (A) and the two rear factory retainer clips (B), retain for installation of Fender Flares. Rentainer clips (B) will need to be removed using needle noise pliers.
STEP 13: Place the Fender Flare onto the vehicle and fit into the correct position following the contours of the body. Using 7.0mm head screwdriver reinstall the previously removed factory spat screws at the upper and lower (A) screw locations through the slots in the front of the Fender Flare at the two noted locations. Re-install the factory retainer clips (B) through the holes in the fender flare at the two noted locations. EGR FIT-FF1000 Front
Bolt On Look Fender Flares - Step 13STEP 14: Use 4 of the U-style clips to secure the Fender Flare to the body. Make sure the barb in the clip securely attaches in the slot on the Fender Flare. Repeat installation method for other side. Double check the front Fender Flares to make sure all bolts are tight and clips  are securely fastened. Your installation is now complete. Do not use abrasive cleaners.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals